* Remove noop CANNED_MESSAGE_MODULE_ENABLE define
* Remove over-eager warning removal
* Remove unused LED_CONN
* Dead defines removal
* Rename oddball LED pin name
* Rename second oddball LED pin name
* Remove another dead define
Using long interleaving is not a breaking change, the receiver node is able
to use the lora header to know if LI encoding is used or not and will
decode LI packets correctly.
However the problem is SX127x and other first generation LoRa IP which do not
support LI at all, for theses it is a breaking change.
HOWEVER due to the sync word bug the LR11x0 already can't talk with SX127x,
so if we enable LI on theses no one would be able to tell.
Same for SX128x altho this is because it works on 2.4Ghz which is incompatible with SX127x.
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
- STM32WLE5CCU6
- NFC (unsupported): NXP NT3H2211W0FTTJ (NTAG I2C plus: NFC Forum T2T with I2C interface, password protection and energy harvesting)
- Sensor (unsupported): Analog ADuCM355 (SHTC3 is connected to ADuCM355 and not directly accessible)
- Bicolor LED
- User button (presently not functional in STM32 variants)
The definitions for sensor voltage control are present but commented out to save power, due to lack of sensor support.
Powered by 4x 4000mAh RAMWAY ER18505 Li-SOCl2 batteries.
Flashing:
1. Power down device (remove batteries)
2. Connect USB-UART to J1 (USART2), pinout is below, do not connect +3V3 pin yet
3. Short BOOT pins next to J1
4. Connect +3V3 pin or insert batteries while BOOT pins are shorted
5. Use STM32CubeProgrammer, connect by UART mode
6. Load firmware .hex and download
J1 (USART2); Molex Picoblade (P=1.25mm * 4)
1. +3V3
2. PA3_USART2_RX_J1
3. PA2_USART2_TX_J1
4. GND
Signed-off-by: Andrew Yong <me@ndoo.sg>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* better logic to check if the RAK12035 soil sensor is calibrated, better log messaging if either of the default values were used.
* .
* changes to how default calibration is done and a message it the default calibration is used pointing to the actual calibration sketch so the user can find it and use it to improve accuracy.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Just set LED_BUILTIN universally to -1, as we don't use it.
* LUD_BUILTIN workarounds
* Squash the LED_BUILTINs that sneaked in
* Don't kill valid pin derfine
* First steps in consolidating code and minimizing rewrite
* Continuing code cleanup
* Merge containsBell and !isMuted to a single code path
* Forgot about alert_message_buzzer in the cleanup
* More code refinements and cleanup
* Fix nagCycleCutoff
* CoPilot Updates
* InkHUD: Region Picker on initial setup
* Added Node Config menu with Lora Region Picker
* Role picker
* Preset Picker
* Timezone picker added
* Power save mode and bluetooth configs
* Config section Headers
* Channel Config
* Cleaning some behavior
* Add back to all Options
* Display config added
* Position Toggle added
* Network Config for ESP32
* Wifi details
* Reduce line spacing to fit more content
* Recent list with checkboxes
* Timezone labels easier to understand
* Trunk fix
* Added "Saving Changes" screen when reboot is needed
* Trunk fix
* Make Tips show after first boot if the region is Unset
* Added ResetDB and keep only favorite commands
* quick fix to joystick
* Trunk Fix
* Fix to tips to work with new joystick input
* Added ADC multiplier value display on power config
* added ADC calibration feature
* Fixed missing stray endiff
* GPS toggle now is aware if gps is present.
Support softsleep by defining PIN_GPS_STANDBY on CDTop CD-PA1010D.
This differs from existing MTK GPS e.g. L76K, where pulling PIN_GPS_STANDBY (WAKE-UP pin) low is not sufficient to put the GPS module in standby.
An additional `$PMTK225,4*2F` must be sent to enter "Backup Mode", which is exited by bringing PIN_GPS_STANDBY (WAKE-UP pin) high.
Refer to datasheet[0] §1.9.3 "Backup Mode".
0: https://cdn-learn.adafruit.com/assets/assets/000/084/295/original/CD_PA1010D_Datasheet_v.03.pdf
Signed-off-by: Andrew Yong <me@ndoo.sg>
* Minimesh Lite Added
* Add Minimesh Lite NRF
* Added board_level = extra
* Fix formatting and optimize image for Minimesh Lite
* Change image
* The image has been deleted.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Improve NRF52 bluetooth power efficiency
* test T114 bad LFXO
* T1000 test
* force BLE param negotiation
* stash
* NRF52 bluetooth small cleanup
* fix potential connectivity issues
* lower BLE min interval to make iOS happy
* remove slave latency negotation
* add BLE issue comment
* code format
* Revert "code format"
This reverts commit 1f92b09d08.
* remove LFCLK debug info
* Fix
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
