Merge branch 'master' into moar-nxp

arch/portduino/portduino.ini

@@ -39,6 +39,7 @@ build_flags =
   -Isrc/platform/portduino
   -DRADIOLIB_EEPROM_UNSUPPORTED
   -DPORTDUINO_LINUX_HARDWARE
+  -DNXP_WIRE=Wire
   -DHAS_UDP_MULTICAST
   -lpthread
   -lstdc++fs

platformio.ini

@@ -26,7 +26,6 @@ build_flags = -Wno-missing-field-initializers
 	-DUSE_THREAD_NAMES
 	-DTINYGPS_OPTION_NO_CUSTOM_FIELDS
 	-DPB_ENABLE_MALLOC=1
-	-DRADIOLIB_LOW_LEVEL=1
 	-DRADIOLIB_EXCLUDE_CC1101=1
 	-DRADIOLIB_EXCLUDE_NRF24=1
 	-DRADIOLIB_EXCLUDE_RF69=1
@@ -73,6 +72,8 @@ lib_deps =
 	nanopb/Nanopb@0.4.91
 	# renovate: datasource=custom.pio depName=ErriezCRC32 packageName=erriez/library/ErriezCRC32
 	erriez/ErriezCRC32@1.0.1
+	https://github.com/meshtastic/SE05X#031f8feccae62689ebbd06914b44bd88547535af
+
 
 ; Used for the code analysis in PIO Home / Inspect
 check_tool = cppcheck

src/detect/ScanI2CTwoWire.cpp

@@ -1,8 +1,8 @@
 #include "ScanI2CTwoWire.h"
 
 #if !MESHTASTIC_EXCLUDE_I2C
-
 #include "concurrency/LockGuard.h"
+#include <SE05X.h>
 #if defined(ARCH_PORTDUINO)
 #include "linux/LinuxHardwareI2C.h"
 #endif
@@ -507,6 +507,10 @@ void ScanI2CTwoWire::scanPort(I2CPort port, uint8_t *address, uint8_t asize)
                 if (len == 5 && memcmp(expectedInfo, info, len) == 0) {
                     LOG_INFO("NXP SE050 crypto chip found");
                     type = NXP_SE050;
+                    if (SE05X.begin()) {
+                        LOG_INFO("NXP Random %u", SE05X.random(65535));
+                        LOG_INFO("NXP Serial Number: %s", SE05X.serialNumber().c_str());
+                    }
 
                 } else {
                     LOG_INFO("FT6336U touchscreen found");

src/main.cpp

@@ -214,8 +214,6 @@ bool pauseBluetoothLogging = false;
 
 bool pmu_found;
 
-uint8_t pa_fan_percentage = 50;
-
 #if !MESHTASTIC_EXCLUDE_I2C
 // Array map of sensor types with i2c address and wire as we'll find in the i2c scan
 std::pair<uint8_t, TwoWire *> nodeTelemetrySensorsMap[_meshtastic_TelemetrySensorType_MAX + 1] = {};
@@ -1377,36 +1375,16 @@ void setup()
     mqttInit();
 #endif
 
-#ifdef RADIO_FAN_EN
-    // Ability to disable FAN if PIN has been set with RADIO_FAN_EN.
+#ifdef RF95_FAN_EN
+    // Ability to disable FAN if PIN has been set with RF95_FAN_EN.
     // Make sure LoRa has been started before disabling FAN.
-#ifdef RADIO_FAN_PWM
-#if defined(ARCH_ESP32)
-    // Set up PWM at Channel 1 at 25KHz, using 8-bit resolution
-    // Turn ON/OFF fan to the specified value if enabled by config.
-    // code by https://github.com/gjelsoe/
-    if (ledcSetup(1, 25000, 8)) {
-        ledcAttachPin(RADIO_FAN_EN, 1);
-        LOG_INFO("PWM init C1 P%d\n", RADIO_FAN_EN);
-        // Set PWM duty cycle based on fan disabled state
-        ledcWrite(1, config.lora.pa_fan_disabled ? 0 : (pa_fan_percentage * 2.55));
-    } else {
-        LOG_WARN("PWM init fail P%d\n", RADIO_FAN_EN);
-    }
-#elif defined(ARCH_NRF52)
-    pinMode(RADIO_FAN_EN, OUTPUT);
-    analogWrite(RADIO_FAN_EN, config.lora.pa_fan_disabled ? 0 : (pa_fan_percentage * 2.55));
-#endif
-#else
-    // Set up as ON/OFF switch of fan
-    pinMode(RADIO_FAN_EN, OUTPUT);
-    digitalWrite(RADIO_FAN_EN, LOW ^ 0);
-#endif
+    if (config.lora.pa_fan_disabled)
+        digitalWrite(RF95_FAN_EN, LOW ^ 0);
 #endif
 
 #ifndef ARCH_PORTDUINO
 
-    // Initialize Wifi
+        // Initialize Wifi
 #if HAS_WIFI
     initWifi();
 #endif

src/main.h

@@ -78,8 +78,6 @@ extern uint32_t shutdownAtMsec;
 
 extern uint32_t serialSinceMsec;
 
-extern uint8_t pa_fan_percentage;
-
 // If a thread does something that might need for it to be rescheduled ASAP it can set this flag
 // This will suppress the current delay and instead try to run ASAP.
 extern bool runASAP;

src/mesh/LR11x0Interface.cpp

@@ -3,7 +3,6 @@
 #include "Throttle.h"
 #include "configuration.h"
 #include "error.h"
-#include "main.h"
 #include "mesh/NodeDB.h"
 #ifdef LR11X0_DIO_AS_RF_SWITCH
 #include "rfswitch.h"
@@ -55,8 +54,6 @@ template <typename T> bool LR11x0Interface<T>::init()
     digitalWrite(LR11X0_POWER_EN, HIGH);
 #endif
 
-    enableFan();
-
 #if ARCH_PORTDUINO
     float tcxoVoltage = (float)settingsMap[dio3_tcxo_voltage] / 1000;
 // FIXME: correct logic to default to not using TCXO if no voltage is specified for LR11x0_DIO3_TCXO_VOLTAGE

src/mesh/RF95Interface.cpp

@@ -154,7 +154,10 @@ bool RF95Interface::init()
     digitalWrite(RF95_TXEN, 0);
 #endif
 
-    enableFan();
+#ifdef RF95_FAN_EN
+    pinMode(RF95_FAN_EN, OUTPUT);
+    digitalWrite(RF95_FAN_EN, 1);
+#endif
 
 #ifdef RF95_RXEN
     pinMode(RF95_RXEN, OUTPUT);
@@ -327,7 +330,10 @@ bool RF95Interface::sleep()
     // put chipset into sleep mode
     setStandby(); // First cancel any active receiving/sending
     lora->sleep();
-    disableFan();
+
+#ifdef RF95_FAN_EN
+    digitalWrite(RF95_FAN_EN, 0);
+#endif
 
     return true;
 }

src/mesh/RadioLibInterface.cpp

@@ -531,37 +531,4 @@ bool RadioLibInterface::startSend(meshtastic_MeshPacket *txp)
 
         return res == RADIOLIB_ERR_NONE;
     }
-}
-
-void RadioLibInterface::enableFan()
-{
-#ifdef RADIO_FAN_EN
-
-#ifdef RADIO_FAN_PWM
-#if defined(ARCH_ESP32)
-    ledcWrite(1, config.lora.pa_fan_disabled ? 0 : (pa_fan_percentage * 2.55));
-#elif defined(ARCH_NRF52)
-    analogWrite(RADIO_FAN_EN, config.lora.pa_fan_disabled ? 0 : (pa_fan_percentage * 2.55));
-#endif
-#else
-    pinMode(RADIO_FAN_EN, OUTPUT);
-    digitalWrite(RADIO_FAN_EN, 1);
-#endif
-#endif
-}
-
-void RadioLibInterface::disableFan()
-{
-#ifdef RADIO_FAN_EN
-#ifdef RADIO_FAN_PWM
-#if defined(ARCH_ESP32)
-    ledcWrite(1, 0);
-#elif defined(ARCH_NRF52)
-    analogWrite(RADIO_FAN_EN, 0);
-#endif
-#else
-    pinMode(RADIO_FAN_EN, OUTPUT);
-    digitalWrite(RADIO_FAN_EN, 0);
-#endif
-#endif
 }

src/mesh/RadioLibInterface.h

@@ -146,9 +146,6 @@ class RadioLibInterface : public RadioInterface, protected concurrency::Notified
     /** Attempt to find a packet in the TxQueue. Returns true if the packet was found. */
     virtual bool findInTxQueue(NodeNum from, PacketId id) override;
 
-    void enableFan();
-    void disableFan();
-
   private:
     /** if we have something waiting to send, start a short (random) timer so we can come check for collision before actually
      * doing the transmit */

src/mesh/SX126xInterface.cpp

@@ -52,8 +52,6 @@ template <typename T> bool SX126xInterface<T>::init()
     pinMode(SX126X_POWER_EN, OUTPUT);
 #endif
 
-    enableFan();
-
 #if ARCH_PORTDUINO
     tcxoVoltage = (float)settingsMap[dio3_tcxo_voltage] / 1000;
     if (settingsMap[sx126x_ant_sw_pin] != RADIOLIB_NC) {

src/mesh/SX128xInterface.cpp

@@ -35,7 +35,10 @@ template <typename T> bool SX128xInterface<T>::init()
     digitalWrite(SX128X_POWER_EN, HIGH);
 #endif
 
-    enableFan();
+#ifdef RF95_FAN_EN
+    pinMode(RF95_FAN_EN, OUTPUT);
+    digitalWrite(RF95_FAN_EN, 1);
+#endif
 
 #if ARCH_PORTDUINO
     if (settingsMap[rxen_pin] != RADIOLIB_NC) {

src/modules/AdminModule.cpp

@@ -706,21 +706,13 @@ void AdminModule::handleSetConfig(const meshtastic_Config &c)
             requiresReboot = false;
         }
 
-#ifdef RADIO_FAN_EN
-#ifdef RADIO_FAN_PWM
-#if defined(ARCH_ESP32)
-        ledcWrite(1, c.payload_variant.lora.pa_fan_disabled ? 0 : (pa_fan_percentage * 2.55));
-#elif defined(ARCH_NFR52)
-        analogWrite(RADIO_FAN_EN, c.payload_variant.lora.pa_fan_disabled ? 0 : (pa_fan_percentage * 2.55));
-#endif
-#else
+#ifdef RF95_FAN_EN
         // Turn PA off if disabled by config
         if (c.payload_variant.lora.pa_fan_disabled) {
-            digitalWrite(RADIO_FAN_EN, LOW ^ 0);
+            digitalWrite(RF95_FAN_EN, LOW ^ 0);
         } else {
-            digitalWrite(RADIO_FAN_EN, HIGH ^ 0);
+            digitalWrite(RF95_FAN_EN, HIGH ^ 0);
         }
-#endif
 #endif
         config.lora = c.payload_variant.lora;
         // If we're setting region for the first time, init the region

variants/betafpv_2400_tx_micro/variant.h

@@ -12,7 +12,7 @@
 #define LORA_MISO 19
 #define LORA_MOSI 23
 #define LORA_CS 5
-#define RADIO_FAN_EN 17
+#define RF95_FAN_EN 17
 
 // #define LED_PIN 16 // This is a LED_WS2812 not a standard LED
 #define HAS_NEOPIXEL                         // Enable the use of neopixels

variants/radiomaster_900_bandit/variant.h

@@ -46,8 +46,7 @@
   FAN is active at 250mW on it's ExpressLRS Firmware.
   This FAN has TACHO signal on Pin 27 for use with PWM.
 */
-#define RADIO_FAN_EN 2
-#define RADIO_FAN_PWM
+#define RF95_FAN_EN 2
 
 /*
   LED PIN setup and it has a NeoPixel LED.

variants/radiomaster_900_bandit_nano/variant.h

@@ -32,7 +32,7 @@
   This unit has a FAN built-in.
   FAN is active at 250mW on it's ExpressLRS Firmware.
 */
-#define RADIO_FAN_EN 2
+#define RF95_FAN_EN 2
 
 /*
   LED PIN setup.

variants/radiomaster_nomad_gemini/platformio.ini

@@ -1,20 +0,0 @@
-[env:radiomaster_nomad_gemini]
-extends = esp32_base
-board = esp32doit-devkit-v1
-build_flags =
-  ${esp32_base.build_flags}
-  -DRADIOMASTER_NOMAD_GEMINI
-  -DPRIVATE_HW
-  -DVTABLES_IN_FLASH=1
-  -DCONFIG_DISABLE_HAL_LOCKS=1
-  -O2
-  -Ivariants/radiomaster_nomad_gemini
-  -DMESHTASTIC_EXCLUDE_ENVIRONMENTAL_SENSOR=1
-  -DMESHTASTIC_EXCLUDE_I2C=1
-  -DRADIOLIB_EXCLUDE_SX128X=1
-  -DRADIOLIB_EXCLUDE_SX127X=1
-  -DRADIOLIB_EXCLUDE_SX126X=1
-board_build.f_cpu = 240000000L
-upload_protocol = esptool
-lib_deps =
-  ${esp32_base.lib_deps}

variants/radiomaster_nomad_gemini/rfswitch.h

@@ -1,56 +0,0 @@
-#include "RadioLib.h"
-
-static const uint32_t rfswitch_dio_pins[] = {RADIOLIB_LR11X0_DIO5, RADIOLIB_LR11X0_DIO6, RADIOLIB_LR11X0_DIO7,
-                                             RADIOLIB_LR11X0_DIO8, RADIOLIB_NC};
-
-static const Module::RfSwitchMode_t rfswitch_table[] = {
-    // mode                  DIO5  DIO6 DIO7 DIO8
-    {LR11x0::MODE_STBY, {LOW, LOW, LOW, LOW}},   {LR11x0::MODE_RX, {LOW, LOW, HIGH, LOW}},
-    {LR11x0::MODE_TX, {LOW, LOW, LOW, HIGH}},    {LR11x0::MODE_TX_HP, {LOW, LOW, LOW, HIGH}},
-    {LR11x0::MODE_TX_HF, {LOW, HIGH, LOW, LOW}}, {LR11x0::MODE_GNSS, {LOW, LOW, LOW, LOW}},
-    {LR11x0::MODE_WIFI, {HIGH, LOW, LOW, LOW}},  END_OF_MODE_TABLE,
-};
-
-/*
-
-DIO5: RXEN 2.4GHz
-DIO6: TXEN 2.4GHz
-DIO7: RXEN 900MHz
-DIO8: TXEN 900MHz
-
-
-  "radio_dcdc": true,
-  "radio_rfo_hf": true,
-
-    "power_apc2": 26,
-    "power_min": 0,
-    "power_high": 6,
-    "power_max": 6,
-    "power_default": 3,
-    "power_control": 3, POWER_OUTPUT_DACWRITE // use internal dacWrite function to set value on GPIO_PIN_RFamp_APC2
-                         [0,   1,   2,   3,   4,   5,   6 ] // 0-6
-    "power_values":      [120, 120, 120, 120, 120, 120, 95] // DAC Value
-    "power_values2":     [-17, -16, -14, -11, -7,  -3,  5 ] // 900M
-    "power_values_dual": [-18, -14,  -8,  -6, -2,   3,  5 ] // 2.4G
-
-    // default value 0 means direct!
-#define POWER_OUTPUT_DACWRITE (hardware_int(HARDWARE_power_control)==3)
-#define POWER_OUTPUT_VALUES hardware_i16_array(HARDWARE_power_values)
-#define POWER_OUTPUT_VALUES_COUNT hardware_int(HARDWARE_power_values_count)
-#define POWER_OUTPUT_VALUES2 hardware_i16_array(HARDWARE_power_values2)
-#define POWER_OUTPUT_VALUES_DUAL hardware_i16_array(HARDWARE_power_values_dual)
-#define POWER_OUTPUT_VALUES_DUAL_COUNT hardware_int(HARDWARE_power_values_dual_count)
-
-#define GPIO_PIN_FAN_EN hardware_pin(HARDWARE_misc_fan_en)
-
-    case PWR_10mW: return 10;
-    case PWR_25mW: return 14;
-    case PWR_50mW: return 17;
-    case PWR_100mW: return 20;
-    case PWR_250mW: return 24;
-    case PWR_500mW: return 27;
-    case PWR_1000mW: return 30;
-
-    95 -> +25dBm
-    120 -> +24dBm
-*/

variants/radiomaster_nomad_gemini/variant.h

@@ -1,60 +0,0 @@
-#define HAS_SCREEN 0
-#define HAS_WIRE 0
-#define HAS_GPS 0
-#undef GPS_RX_PIN
-#undef GPS_TX_PIN
-
-#define PIN_SPI_MISO 33
-#define PIN_SPI_MOSI 32
-#define PIN_SPI_SCK 25
-#define PIN_SPI_NSS 27
-
-#define LORA_RESET 15
-#define LORA_DIO1 37
-#define LORA_DIO2 36
-#define LORA_SCK PIN_SPI_SCK
-#define LORA_MISO PIN_SPI_MISO
-#define LORA_MOSI PIN_SPI_MOSI
-#define LORA_CS PIN_SPI_NSS
-
-// supported modules list
-#define USE_LR1121
-
-#define LR1121_IRQ_PIN LORA_DIO1
-#define LR1121_NRESET_PIN LORA_RESET
-#define LR1121_BUSY_PIN LORA_DIO2
-#define LR1121_SPI_NSS_PIN LORA_CS
-#define LR1121_SPI_SCK_PIN LORA_SCK
-#define LR1121_SPI_MOSI_PIN LORA_MOSI
-#define LR1121_SPI_MISO_PIN LORA_MISO
-
-// this is correct and sets the cap for the Sub-GHz part
-#define LR1110_MAX_POWER 5
-// 2.4G Part
-#define LR1120_MAX_POWER 5
-
-#define POWER_SHIFT -20
-
-// not yet implemented
-#define JANUS_RADIO
-#define LR1121_IRQ2_PIN 34
-#define LR1121_NRESET2_PIN 21
-#define LR1121_BUSY2_PIN 39
-#define LR1121_SPI_NSS2_PIN 13
-
-// TODO: check if this is correct
-// #define LR11X0_DIO3_TCXO_VOLTAGE 1.6
-#define LR11X0_DIO_AS_RF_SWITCH
-
-#define HAS_NEOPIXEL                         // Enable the use of neopixels
-#define NEOPIXEL_COUNT 2                     // How many neopixels are connected
-#define NEOPIXEL_DATA 22                     // GPIO pin used to send data to the neopixels
-#define NEOPIXEL_TYPE (NEO_GRB + NEO_KHZ800) // Type of neopixels in use
-#define ENABLE_AMBIENTLIGHTING               // Turn on Ambient Lighting
-
-#define BUTTON_PIN 34
-#define BUTTON_NEED_PULLUP
-
-#undef EXT_NOTIFY_OUT
-
-#define RADIO_FAN_EN 2

variants/rak4631/platformio.ini

@@ -11,6 +11,7 @@ build_flags = ${nrf52840_base.build_flags} -Ivariants/rak4631 -D RAK_4631
   -DRADIOLIB_EXCLUDE_SX128X=1
   -DRADIOLIB_EXCLUDE_SX127X=1
   -DRADIOLIB_EXCLUDE_LR11X0=1
+  -DNXP_WIRE=Wire
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/rak4631> +<mesh/eth/> +<mesh/api/> +<mqtt/>
 lib_deps = 
   ${nrf52840_base.lib_deps}