We set the buffer size to about a byte on NRF52480, less than
other platforms:
esp32.ini: -DSERIAL_BUFFER_SIZE=4096
esp32c6.ini: -DSERIAL_BUFFER_SIZE=4096
nrf52.ini: -DSERIAL_BUFFER_SIZE=1024
However, 115200 baud, like the T1000e uses is about 12 times that
- almost 15 bytes per millisecond.
15 bytes * 200 millisecond (our GPS poll rate) = 3000 bytes, which is longer than our buffer
on the nrf52 platform. This causes "GPS Buffer full" errors on the T1000e
and other devices based on NRF52480 with newer GPS chips.
This patch increases SERIAL_BUFFER_SIZE for nrf52480 to 4096 to align with
other platforms. It keeps the original 1024 for the nrf52832, which has
fewer resources.
Fixes https://github.com/meshtastic/firmware/issues/5767
* Improve NRF52 bluetooth power efficiency
* test T114 bad LFXO
* T1000 test
* force BLE param negotiation
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add mesh/Default.h include.
* Reflacter OnScreenKeyBoard Module, do not interrupt keyboard when new message comes.
* feat: Add long press scrolling for Joystick and upDown Encoder on baseUI frames and menus.
* refactor: Clean up code formatting and improve readability in Screen and OnScreenKeyboardModule
* Fix navigation on UpDownEncoder, default was RotaryEncoder while bringing the T_LORA_PAGER
* Update src/graphics/draw/MenuHandler.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/modules/OnScreenKeyboardModule.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/graphics/draw/NotificationRenderer.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Optimize the detection logic for repeated events of the arrow keys.
* Fixed parameter names in the OnScreenKeyboardModule::start
* Trunk fix
* Reflator OnScreenKeyboard Input checking, make it simple
* Simplify long press logic in OnScreenKeyboardModule.
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* changes of variants/nrf52840/nrf52.ini and variants/nrf52840/rak4631/platformio.ini
* try for nrf52 size reduction, faketec exclude unused radios and meshlink refactor
* can't exclude LR11X0 as in schematic there's option for LR1121
* remove -Map flag and -Wl
* removed spaces causing error
---------
Co-authored-by: macvenez <macvenez@gmail.com>
* Delete variants/nrf52840/diy/nrf52_promicro_diy_tcxo/Schematic_Pro-Micro_Pinouts.pdf
remove old file
* Add updated schematic
* Update GPS TX and RX pin definitions after swap
* Update GPS pin definitions and schematic link
Updated the schematic link to reflect GPS pin definition changes.
* Plain RAK4631 should not compile EInk and TFT display code
* Add USE_TFTDISPLAY to variant files.
* Derp
* Undo the platformio.ini changes to heltec_v4
* Drop unneeded src_filter lines
---------
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Jason P <applewiz@mac.com>
* Flags and scripts for size reduction on NRF52 -> Currently targeting rak4631
* Changes from the other branch poluted it
* Remove the stripper
* No strip
* Add initial support for Hackaday Communicator
* Fork it!
* Trunk
* Remove unused elements from the HackadayCommunicatorKeyboard
* Don't divide by zero.
* remove duplicate HAS_LP5562 introduced by #6422
* add ST7796
* changes to get display centered+lib update
* seperated from tbeam
* forgot the simple scan case
* lowered speeds to 1/4
* added SPI Speed to constructor+ cleaned up variant.h
* even slower speeds....
* add ST7796
* changes to get display centered+lib update
* seperated from tbeam
* forgot the simple scan case
* lowered speeds to 1/4
* added SPI Speed to constructor+ cleaned up variant.h
* even slower speeds....
* changed variant name to tbeam-displayshield
* modified variant.h and merged ini file+testing on lower spi frequency for the lora module, display shield pumps out EMI?
* try higher speeds + HSPI
* cleanup of redundant code
* refelct changes?
* trunk fmt
* testing touchscreen code
* further testing
* changed to sensorlib 0.3.1
* i broke it , dont know how to fix at the moment will investigate
* add -1 functionality for touch IRQ
* revert to working example?
* it works.... is pressed was not working properly
* working touchscreen but gestures not moving display
* swap XY+ mirror X
* cleanup + addition of defines for on screen keyboard and canned message module
* removed debug lines, disabled bluetooth for now because of stack smashing protect failure
* reverted the revert #6640 + increased speed, bleutooth is stable now on reconnection cold booth etc , GPS is still not working though
* remove debug + add fixed baudrate for gps
* fmt
* revert NIMble
* changed display library to meshtastic org
* removed baudrate of 115200 and some commented out code
* Correct spelling
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Typo
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* display speed x10
* resolve conflicts
* undo
* revert speed increase CPU
* add SCREEN_TRANSITION_FRAMERATE 5
* spi speed increase of the display
* using the original touchscreen implementation
* removal of H file line
* add USE_ST7796 to missing places
* removed is pressed + interrupt
* revert changes of settings.json
* update to screen.cpp
* test identification of CST226 and CST328
* Update src/configuration.h
typo
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* made changes to detection because it was completely wrong, CST226SE has 2 posible adresses
* add merge queue
* try vars
* kerning in yaml.
* update comment
* lint etc
* touching to check grandfathering
* explicit ignores
* add WIP for Unit C6L (#7433)
* add WIP for Unit C6L
* adapt to new config structure
* Add c6l BLE and screen support (#7991)
* Minor c6l fix
* Move out of PRIVATE_HW
---------
Co-authored-by: Austin <vidplace7@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Jason P <Xaositek@users.noreply.github.com>
Co-authored-by: Markus <Links2004@users.noreply.github.com>
* Update Adafruit BusIO to v1.17.3 (#8018)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Update actions/checkout action to v5 (#8020)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Update actions/setup-python action to v6 (#8023)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Upgrade trunk (#8025)
Co-authored-by: vidplace7 <1779290+vidplace7@users.noreply.github.com>
* Update actions/download-artifact action to v5 (#8021)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Fix init for InputEvent (#8015)
* Automated version bumps (#8028)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Allow Left / Right Events for selection and improve encoder responsives (#8016)
* Allow Left / Right Events for selection and improve encoder responsives
* add define for ROTARY_DELAY
* T-Lora Pager: Support LR1121 and SX1280 models (#7956)
* T-Lora Pager: Support LR1121 and SX1280 models
* Remove ifdefs
* (resubmission) Manual GitHub actions to allow building one target or arch (#7997)
* Reset the modified files
* Fix some changes
* Fix some changes
* Trunk. That is all.
---------
Co-authored-by: Tom <116762865+Nestpebble@users.noreply.github.com>
* BaseUI Show/Hide Frame Functionality (#7382)
* Rename System Frame (from Memory) in code base
* Create menu options to Show/Hide frames: Node Lists, Bearings, Position, LoRa, Clock and Favorites frames
* Move Region Picker into submenu
* Tweak wording for Send Position vs Node Info if the device has GPS
* Update actions/checkout action to v5 (#8031)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Update actions/download-artifact action to v5 (#8032)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Update actions/setup-python action to v6 (#8033)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Phone GPS display on Position Screen for BaseUI (#7875)
* Phone GPS display on Position Screen
This is a PR to show when a phone shares GPS location with the node so you can reliably know what coordinate is being shared with the Mesh.
* Merge pull request #8004 from compumike/compumike/debug-heap-add-free-heap-debugging-to-all-log-lines
When `DEBUG_HEAP` is defined, add free heap bytes to every log line in `RedirectablePrint::log_to_serial`
* Feature: Seamless Cross-Preset Communication via UDP Multicast Bridging (#7753)
* Added compatibility between nodes on different Presets through `Mesh via UDP`
* Optimize multicast handling and channel mapping
- FloodingRouter: remove redundant UDP-encrypted rebroadcast suppression.
- Router: guard multicast fallback with HAS_UDP_MULTICAST and map fallback-decoded packets
to the local default channel via isDefaultChannel()
- UdpMulticastHandler: set transport_mechanism only after successful decode
* trunk fmt
* Move setting transport mechanism.
---------
Co-authored-by: GUVWAF <thijs@havinga.eu>
* Auto-favorite remote admin node
* Merge pull request #7873 from compumike/compumike/client-base-role
Add `CLIENT_BASE` role: `ROUTER` for favorites, `CLIENT` otherwise (for attic/roof nodes!)
* Fixes
* BaseUI Updates (#7787)
* Account for low resolution wide screen OLEDs
* Allow picking of Device Role and new Display Formatter for Device Role
* Add remainder of client roles to display formatter
* Don't update the role unless you pick a value
* Mascots are fun
* Fix warnings during compile time
* Improve some menus
* Mascots need to work everywhere
* Update Chirpy image
* Fix Trunk
* Update protobufs
* Add date to Clock screen
* Analog clocks love dates too
* Finalize date moves for analog clock
* Added Last Coordinate counter to Position screen (#7865)
Adding a counter to show the last time a GPS coordinate was detected to ensure the user is aware how long since the coordinate updated or to identify any errors.
* Fix
* Portduino config refactor (#7796)
* Start portduino_config refactor
* refactor GPIOs to new portduino_config
* More portduino_config work
* More conversion to portduino_config
* Finish portduino_config transition
* trunk
* yaml output work
* Simplify the GPIO config
* Trunk
* updated shebang to use a more standard path for bash (#7922)
Signed-off-by: Trenton VanderWert <trenton.vanderwert@gmail.com>
* Show GPS Date properly in drawCommonHeader (#7887)
* Commit good code that is sustainable
* Fix new build errors
* BaseUI Updates (#7787)
* Account for low resolution wide screen OLEDs
* Allow picking of Device Role and new Display Formatter for Device Role
* Add remainder of client roles to display formatter
* Don't update the role unless you pick a value
* Mascots are fun
* Fix warnings during compile time
* Improve some menus
* Mascots need to work everywhere
* Update Chirpy image
* Fix Trunk
* Update protobufs
* Add date to Clock screen
* Analog clocks love dates too
* Finalize date moves for analog clock
* Add formatting and menu picking for other GPS format options (#7974)
* Add back options for other GPS format options
* Rename variables and don't overlap elements
* Fix default value
* Should probably add a menu while I'm here!
* Shorten names just a bit to fit on screens
* Fix off by one
* Labels try to make things better
* Missed a label
* Update protobufs (#8038)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Add formatting and menu picking for other GPS format options (#7974)
* Add back options for other GPS format options
* Rename variables and don't overlap elements
* Fix default value
* Should probably add a menu while I'm here!
* Shorten names just a bit to fit on screens
* Fix off by one
* Labels try to make things better
* Missed a label
* Add a new GPS model CM121. (#7852)
* Add a new GPS model CM121.
* Add CM121 to Unicore.
* Trunk fixes, remove unneded NMEA lines
---------
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* (resubmission) Manual GitHub actions to allow building one target or arch (#7997)
* Reset the modified files
* Fix some changes
* Fix some changes
* Trunk. That is all.
---------
Co-authored-by: Tom <116762865+Nestpebble@users.noreply.github.com>
* PPA: Enable Ubuntu 25.10 (questing) (#7940)
* Update Protobuf usage, add MLS, fix clock (#8041)
* Update protobufs (#8045)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Fix icon
* C6l fixes (#8047)
* fix build with HAS_TELEMETRY 0 (#8051)
* Make sure to ACK ACKs/replies if next-hop routing is used (#8052)
* Make sure to ACK ACKs/replies if next-hop routing is used
To stop their retransmissions; hop limit of 0 is enough
* Update src/mesh/ReliableRouter.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* move HTTP contentTypes to Flash - saves 768 Bytes of RAM (#8055)
* Use `lora.use_preset` config to get name (#8057)
* Update RadioLib to v7.3.0 (#8065)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Fix Rotary Encoder Button (#8001)
this fixes the Rotary Encoder Button, currenlty its not working at all.
Currently the action `ROTARY_ACTION_PRESSED` is only triggerd with a IRQ on RISING, which results in nothing since the function detects the "not longer" pressed button --> no action.
the `ROTARY_ACTION_PRESSED` implementation needs to be called on both edges (on press and release of the button)
changing the interupt setting to `CHANGE` fixes the problem.
* Add another seeed_xiao_nrf52840_kit build environment for I2C pinout (#8036)
* Update platformio.ini
* Remove some more extraneous lines
* Add heltec_v4 board. (#7845)
* add heltec_v4 board.
* Update variants/esp32s3/heltec_v4/platformio.ini
Co-authored-by: Austin <vidplace7@gmail.com>
* Limit the maximum output power.
* Trunk fixes
Fixes formatting to match meshtastic trunk linter.
* Apply suggestion from @Copilot
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Apply suggestion from @Copilot
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Austin <vidplace7@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Upgrade trunk (#8078)
Co-authored-by: vidplace7 <1779290+vidplace7@users.noreply.github.com>
* portduino bump to fix gpiod bug (#8083)
An earlier portduino causes problems with initializing gpiod lines. This pulls in the fix.
* Handle ext. notification module things even if not enabled (#8089)
* tlora-pager wake on button, and kb backlight toggling (#8090)
* Try-fix: Unstick that PhoneAPI state (#8091)
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* Also pull a deviceID from esp32c6 devices (#8092)
* Remove line from BLE pin screen, to make pin readible on tiny screens
* Fix build errors (#8067)
* Heltec V4 is 16mb
* Clear lasttoradio on BLE disconnect (#8095)
* On disconnect, clear the lastToRadio buffer
* Move it, bucko!
* Revert "Fix build errors (#8067)"
This reverts commit d998f70b56.
* Automated version bumps (#8100)
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
* Upgrade trunk (#8094)
Co-authored-by: vidplace7 <1779290+vidplace7@users.noreply.github.com>
* Update Adafruit BusIO to v1.17.4 (#8098)
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
* Add three expansion screens for heltec mesh solar. (#7995)
* Add three expansion screens for heltec mesh solar.
* delete whitespace
Update variants/nrf52840/heltec_mesh_solar/variant.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* delete whitespace
Update variants/nrf52840/heltec_mesh_solar/platformio.ini
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Trunk
---------
Signed-off-by: Trenton VanderWert <trenton.vanderwert@gmail.com>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Dane Evans <dane@goneepic.com>
Co-authored-by: Austin <vidplace7@gmail.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Jason P <Xaositek@users.noreply.github.com>
Co-authored-by: Markus <Links2004@users.noreply.github.com>
Co-authored-by: renovate[bot] <29139614+renovate[bot]@users.noreply.github.com>
Co-authored-by: github-actions[bot] <41898282+github-actions[bot]@users.noreply.github.com>
Co-authored-by: vidplace7 <1779290+vidplace7@users.noreply.github.com>
Co-authored-by: Markus <974709+Links2004@users.noreply.github.com>
Co-authored-by: thebentern <9000580+thebentern@users.noreply.github.com>
Co-authored-by: WillyJL <me@willyjl.dev>
Co-authored-by: Tom <116762865+NomDeTom@users.noreply.github.com>
Co-authored-by: Tom <116762865+Nestpebble@users.noreply.github.com>
Co-authored-by: Jason P <applewiz@mac.com>
Co-authored-by: HarukiToreda <116696711+HarukiToreda@users.noreply.github.com>
Co-authored-by: Michael <michael.overhorst@gmail.com>
Co-authored-by: GUVWAF <thijs@havinga.eu>
Co-authored-by: Trent V. <trenton.vanderwert@gmail.com>
Co-authored-by: Quency-D <55523105+Quency-D@users.noreply.github.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
Co-authored-by: GUVWAF <78759985+GUVWAF@users.noreply.github.com>
* Swap the GPS serial port pins.
* Trunk fixes
---------
Co-authored-by: Jason P <applewiz@mac.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Added OCV_ARRAY from measured discharge curve testing and update ADC multiplier
The ADC resistor divider ratio is 0.6 -> multiplier should be 1/0.6 ~=1.667
We data logged a full discharge curve at constant 100mA draw over 15hours to get a realistic voltage curve for battery SoC measurements.
* Remove power.h in favor of variant.h
---------
Co-authored-by: Jason P <applewiz@mac.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* Make RAK4631 nodes power back on deep sleep
The devices will hang if the VBAT goes under 1.7V (Brown-out reset) and
they will never come back unless power supply goes completely off.
This kills unattended nodes.
Using the SystemOff the LPCOMP we can get the nodes back again when
power comes back, even if VBAT goes under 1.7V, which moreover is more
unlikely because the device is off.
* Adding support for heltec t114
And moved particularities to variant.h
* Remove old cpp comment that belongs to variant.h
It was a leftover.
* Trunk fix
---------
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* Update to Pro-micro variants
Schematic updated
Xtal variant removed
Extra module added to list
Extra explanation added to readme.
* Fix markdown formatting in readme.md
* Fix formatting in readme.md for RF switch section
---------
Co-authored-by: Tom <116762865+Nestpebble@users.noreply.github.com>
* Add the Heltec v4 expansion box.
* Change heltec-v4-oled to heltec-v4.
* Add touchscreen to I2C scanning.
* Add reset and busy pins to the ST7789.
* Ignore the touch interrupt pin and extend the sleep time to 1 hour.
* Remove the default sleep function.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
