[create-pull-request] automated change (#2836)

Co-authored-by: thebentern <thebentern@users.noreply.github.com>

src/mesh/Router.cpp

@@ -359,7 +359,6 @@ bool perhapsDecode(meshtastic_MeshPacket *p)
                     // LOG_DEBUG("\n\n**\n\nDecompressed length - %d \n", decompressed_len);
 
                     memcpy(p->decoded.payload.bytes, decompressed_out, decompressed_len);
-                    p->decoded.payload.size = decompressed_len;
 
                     // Switch the port from PortNum_TEXT_MESSAGE_COMPRESSED_APP to PortNum_TEXT_MESSAGE_APP
                     p->decoded.portnum = meshtastic_PortNum_TEXT_MESSAGE_APP;
@@ -383,7 +382,9 @@ meshtastic_Routing_Error perhapsEncode(meshtastic_MeshPacket *p)
 
     // If the packet is not yet encrypted, do so now
     if (p->which_payload_variant == meshtastic_MeshPacket_decoded_tag) {
-        // Only allow compression on the text message app.
+        size_t numbytes = pb_encode_to_bytes(bytes, sizeof(bytes), &meshtastic_Data_msg, &p->decoded);
+
+        // Only allow encryption on the text message app.
         //  TODO: Allow modules to opt into compression.
         if (p->decoded.portnum == meshtastic_PortNum_TEXT_MESSAGE_APP) {
 
@@ -395,12 +396,17 @@ meshtastic_Routing_Error perhapsEncode(meshtastic_MeshPacket *p)
             int compressed_len;
             compressed_len = unishox2_compress_simple(original_payload, p->decoded.payload.size, compressed_out);
 
-            LOG_DEBUG("Length - %d, compressed length - %d \n", p->decoded.payload.size, compressed_len);
+            LOG_DEBUG("Original length - %d \n", p->decoded.payload.size);
+            LOG_DEBUG("Compressed length - %d \n", compressed_len);
             LOG_DEBUG("Original message - %s \n", p->decoded.payload.bytes);
 
             // If the compressed length is greater than or equal to the original size, don't use the compressed form
             if (compressed_len >= p->decoded.payload.size) {
+
                 LOG_DEBUG("Not using compressing message.\n");
+                // Set the uncompressed payload variant anyway. Shouldn't hurt?
+                // p->decoded.which_payloadVariant = Data_payload_tag;
+
                 // Otherwise we use the compressor
             } else {
                 LOG_DEBUG("Using compressed message.\n");
@@ -413,8 +419,6 @@ meshtastic_Routing_Error perhapsEncode(meshtastic_MeshPacket *p)
             }
         }
 
-        size_t numbytes = pb_encode_to_bytes(bytes, sizeof(bytes), &meshtastic_Data_msg, &p->decoded);
-
         if (numbytes > MAX_RHPACKETLEN)
             return meshtastic_Routing_Error_TOO_LARGE;
 

src/mesh/generated/meshtastic/portnums.pb.h

@@ -69,7 +69,8 @@ typedef enum _meshtastic_PortNum {
  NOTE: audio frames contain a 3 byte header (0xc0 0xde 0xc2) and a one byte marker for the decompressed bitrate.
  This marker comes from the 'moduleConfig.audio.bitrate' enum minus one. */
     meshtastic_PortNum_AUDIO_APP = 9,
-    /* Same as Text Message but originating from Detection Sensor Module. */
+    /* Same as Text Message but originating from Detection Sensor Module.
+ NOTE: This portnum traffic is not sent to the public MQTT starting at firmware version 2.2.9 */
     meshtastic_PortNum_DETECTION_SENSOR_APP = 10,
     /* Provides a 'ping' service that replies to any packet it receives.
  Also serves as a small example module.
@@ -90,7 +91,8 @@ typedef enum _meshtastic_PortNum {
  ENCODING: Protobuf */
     meshtastic_PortNum_STORE_FORWARD_APP = 65,
     /* Optional port for messages for the range test module.
- ENCODING: ASCII Plaintext */
+ ENCODING: ASCII Plaintext
+ NOTE: This portnum traffic is not sent to the public MQTT starting at firmware version 2.2.9 */
     meshtastic_PortNum_RANGE_TEST_APP = 66,
     /* Provides a format to send and receive telemetry data from the Meshtastic network.
  Maintained by Charles Crossan (crossan007) : crossan007@gmail.com

src/modules/Modules.cpp

@@ -31,7 +31,7 @@
 #if defined(ARCH_ESP32) || defined(ARCH_NRF52) || defined(ARCH_RP2040)
 #include "modules/ExternalNotificationModule.h"
 #include "modules/RangeTestModule.h"
-#if (defined(ARCH_ESP32) || defined(ARCH_NRF52)) && !defined(CONFIG_IDF_TARGET_ESP32S2)
+#if (defined(ARCH_ESP32) || defined(ARCH_NRF52) || defined(ARCH_RP2040)) && !defined(CONFIG_IDF_TARGET_ESP32S2)
 #include "modules/SerialModule.h"
 #endif
 #endif
@@ -92,7 +92,8 @@ void setupModules()
             new AirQualityTelemetryModule();
         }
 #endif
-#if (defined(ARCH_ESP32) || defined(ARCH_NRF52)) && !defined(CONFIG_IDF_TARGET_ESP32S2) && !defined(CONFIG_IDF_TARGET_ESP32C3)
+#if (defined(ARCH_ESP32) || defined(ARCH_NRF52) || defined(ARCH_RP2040)) && !defined(CONFIG_IDF_TARGET_ESP32S2) &&               \
+    !defined(CONFIG_IDF_TARGET_ESP32C3)
         new SerialModule();
 #endif
 #ifdef ARCH_ESP32

src/modules/SerialModule.cpp

@@ -44,9 +44,10 @@
 
 */
 
-#if (defined(ARCH_ESP32) || defined(ARCH_NRF52)) && !defined(CONFIG_IDF_TARGET_ESP32S2) && !defined(CONFIG_IDF_TARGET_ESP32C3)
+#if (defined(ARCH_ESP32) || defined(ARCH_NRF52) || defined(ARCH_RP2040)) && !defined(CONFIG_IDF_TARGET_ESP32S2) &&               \
+    !defined(CONFIG_IDF_TARGET_ESP32C3)
 
-#define RX_BUFFER 128
+#define RX_BUFFER 256
 #define TIMEOUT 250
 #define BAUD 38400
 #define ACK 1
@@ -141,7 +142,12 @@ int32_t SerialModule::runOnce()
             }
 #elif !defined(TTGO_T_ECHO)
             if (moduleConfig.serial.rxd && moduleConfig.serial.txd) {
+#ifdef ARCH_RP2040
+                Serial2.setFIFOSize(RX_BUFFER);
+                Serial2.setPinout(moduleConfig.serial.txd, moduleConfig.serial.rxd);
+#else
                 Serial2.setPins(moduleConfig.serial.rxd, moduleConfig.serial.txd);
+#endif
                 Serial2.begin(baud, SERIAL_8N1);
                 Serial2.setTimeout(moduleConfig.serial.timeout > 0 ? moduleConfig.serial.timeout : TIMEOUT);
             } else {
@@ -182,7 +188,7 @@ int32_t SerialModule::runOnce()
                     }
                 }
             }
-#ifndef TTGO_T_ECHO
+#if !defined(TTGO_T_ECHO)
             else {
                 while (Serial2.available()) {
                     serialPayloadSize = Serial2.readBytes(serialBytes, meshtastic_Constants_DATA_PAYLOAD_LEN);

src/modules/SerialModule.h

@@ -8,7 +8,8 @@
 #include <Arduino.h>
 #include <functional>
 
-#if (defined(ARCH_ESP32) || defined(ARCH_NRF52)) && !defined(CONFIG_IDF_TARGET_ESP32S2) && !defined(CONFIG_IDF_TARGET_ESP32C3)
+#if (defined(ARCH_ESP32) || defined(ARCH_NRF52) || defined(ARCH_RP2040)) && !defined(CONFIG_IDF_TARGET_ESP32S2) &&               \
+    !defined(CONFIG_IDF_TARGET_ESP32C3)
 
 class SerialModule : public StreamAPI, private concurrency::OSThread
 {
@@ -74,4 +75,4 @@ class SerialModuleRadio : public MeshModule
 
 extern SerialModuleRadio *serialModuleRadio;
 
-#endif
+#endif

src/mqtt/MQTT.cpp

@@ -455,6 +455,13 @@ void MQTT::onSend(const meshtastic_MeshPacket &mp, ChannelIndex chIndex)
 {
     auto &ch = channels.getByIndex(chIndex);
 
+    if (&mp.decoded && strcmp(moduleConfig.mqtt.address, default_mqtt_address) == 0 &&
+        (mp.decoded.portnum == meshtastic_PortNum_RANGE_TEST_APP ||
+         mp.decoded.portnum == meshtastic_PortNum_DETECTION_SENSOR_APP)) {
+        LOG_DEBUG("MQTT onSend - Ignoring range test or detection sensor message on public mqtt\n");
+        return;
+    }
+
     if (ch.settings.uplink_enabled) {
         const char *channelId = channels.getGlobalId(chIndex); // FIXME, for now we just use the human name for the channel
 

variants/nano-g1-explorer/variant.h

@@ -4,8 +4,8 @@
 #define I2C_SCL 22
 
 #define BUTTON_PIN 36 // The user button (information button) GPIO on the Nano G1 explorer
-//#define BUTTON_PIN_ALT 13 // Alternate GPIO for an external button if needed. Does anyone use this? It is not documented
-// anywhere.
+// #define BUTTON_PIN_ALT 13 // Alternate GPIO for an external button if needed. Does anyone use this? It is not documented
+//  anywhere.
 #define EXT_NOTIFY_OUT 13 // Default pin to use for Ext Notify Module.
 
 // common pinout for their SX1262 vs RF95 modules - both can be enabled and we will probe at runtime for RF95 and if
@@ -13,6 +13,9 @@
 #define USE_RF95
 #define USE_SX1262
 
+#define GPS_RX_PIN 34
+#define GPS_TX_PIN 12
+
 #define LORA_DIO0 26 // a No connect on the SX1262 module
 #define LORA_RESET 23
 #define LORA_DIO1 33 // SX1262 IRQ

variants/nano-g1/variant.h

@@ -4,8 +4,8 @@
 #define I2C_SCL 22
 
 #define BUTTON_PIN 36 // The middle button GPIO on the Nano G1
-//#define BUTTON_PIN_ALT 13 // Alternate GPIO for an external button if needed. Does anyone use this? It is not documented
-// anywhere.
+// #define BUTTON_PIN_ALT 13 // Alternate GPIO for an external button if needed. Does anyone use this? It is not documented
+//  anywhere.
 #define EXT_NOTIFY_OUT 13 // Default pin to use for Ext Notify Module.
 
 // common pinout for their SX1262 vs RF95 modules - both can be enabled and we will probe at runtime for RF95 and if
@@ -13,6 +13,9 @@
 #define USE_RF95
 #define USE_SX1262
 
+#define GPS_RX_PIN 34
+#define GPS_TX_PIN 12
+
 #define LORA_DIO0 26 // a No connect on the SX1262 module
 #define LORA_RESET 23
 #define LORA_DIO1 33 // SX1262 IRQ
@@ -30,4 +33,4 @@
 #endif
 
 // different screen
-#define USE_SH1106
+#define USE_SH1106

variants/rpipico/variant.h

@@ -17,6 +17,10 @@
 // SDA = 4
 // SCL = 5
 
+// Recommended pins for SerialModule:
+// txd = 8
+// rxd = 9
+
 #define EXT_NOTIFY_OUT 22
 #define BUTTON_PIN 17
 

variants/rpipicow/variant.h

@@ -17,6 +17,10 @@
 // SDA = 4
 // SCL = 5
 
+// Recommended pins for SerialModule:
+// txd = 8
+// rxd = 9
+
 #define EXT_NOTIFY_OUT 22
 #define BUTTON_PIN 17
 

version.properties

@@ -1,4 +1,4 @@
 [VERSION]  
 major = 2
 minor = 2
-build = 8
+build = 9