Add libuv to GitHub Actions

Allows anyone to test the PR

.github/FUNDING.yml

@@ -1,3 +0,0 @@
-# These are supported funding model platforms
-
-open_collective: meshtastic

.github/ISSUE_TEMPLATE/Bug Report.yml

@@ -72,15 +72,6 @@ body:
     validations:
       required: true
 
-  - type: checkboxes
-    id: mui
-    attributes:
-      label: Is this bug report about any UI component firmware like InkHUD or Meshtatic UI (MUI)?
-      options:
-        - label: Meshtastic UI aka MUI colorTFT
-        - label: InkHUD ePaper
-        - label: OLED slide UI on any display
-
   - type: input
     id: version
     attributes:

.github/actions/build-variant/action.yml

@@ -27,10 +27,10 @@ inputs:
     description: A newline separated list of paths to store as artifacts
     required: false
     default: ""
-  # include-web-ui:
-  #   description: Include the web UI in the build
-  #   required: false
-  #   default: "false"
+  include-web-ui:
+    description: Include the web UI in the build
+    required: false
+    default: "false"
   arch:
     description: Processor arch name
     required: true
@@ -43,29 +43,22 @@ runs:
       id: base
       uses: ./.github/actions/setup-base
 
-    # - name: Get web ui version
-    #   if: inputs.include-web-ui == 'true'
-    #   id: webver
-    #   shell: bash
-    #   run: |
-    #     echo "ver=$(cat bin/web.version)" >> $GITHUB_OUTPUT
+    - name: Pull web ui
+      if: inputs.include-web-ui == 'true'
+      uses: dsaltares/fetch-gh-release-asset@master
+      with:
+        repo: meshtastic/web
+        file: build.tar
+        target: build.tar
+        token: ${{ inputs.github_token }}
+        version: tags/v2.5.3
 
-    # - name: Pull web ui
-    #   if: inputs.include-web-ui == 'true'
-    #   uses: dsaltares/fetch-gh-release-asset@master
-    #   with:
-    #     repo: meshtastic/web
-    #     file: build.tar
-    #     target: build.tar
-    #     token: ${{ inputs.github_token }}
-    #     version: tags/v${{ steps.webver.outputs.ver }}
-
-    # - name: Unpack web ui
-    #   if: inputs.include-web-ui == 'true'
-    #   shell: bash
-    #   run: |
-    #     tar -xf build.tar -C data/static
-    #     rm build.tar
+    - name: Unpack web ui
+      if: inputs.include-web-ui == 'true'
+      shell: bash
+      run: |
+        tar -xf build.tar -C data/static
+        rm build.tar
 
     - name: Remove debug flags for release
       shell: bash

.github/actions/setup-base/action.yml

@@ -20,7 +20,7 @@ runs:
       shell: bash
       run: |
         sudo apt-get -y update --fix-missing
-        sudo apt-get install -y cppcheck libbluetooth-dev libgpiod-dev libyaml-cpp-dev lsb-release
+        sudo apt-get install -y cppcheck libbluetooth-dev libgpiod-dev libyaml-cpp-dev libuv1-dev lsb-release
 
     - name: Setup Python
       uses: actions/setup-python@v5

.github/dependabot.yml

@@ -0,0 +1,29 @@
+#trunk-ignore-all(yamllint/quoted-strings): required by dependabot syntax check
+version: 2
+updates:
+  - package-ecosystem: docker
+    directory: /.devcontainer
+    schedule:
+      interval: daily
+      time: "05:00"
+      timezone: US/Pacific
+  - package-ecosystem: docker
+    directory: /
+    schedule:
+      interval: daily
+      time: "05:00"
+      timezone: US/Pacific
+  - package-ecosystem: gitsubmodule
+    directory: /
+    schedule:
+      interval: daily
+      time: "05:00"
+      timezone: US/Pacific
+    ignore:
+      - dependency-name: protobufs
+  - package-ecosystem: github-actions
+    directory: /.github/workflows
+    schedule:
+      interval: daily
+      time: "05:00"
+      timezone: US/Pacific

.github/pull_request_template.md

@@ -1,7 +1,7 @@
-## 🙏 Thank you for sending in a pull request, here's some tips to get started!
-
 ### ❌ (Please delete all these tips and replace them with your text) ❌
 
+## Thank you for sending in a pull request, here's some tips to get started!
+
 - Before starting on some new big chunk of code, it it is optional but highly recommended to open an issue first
   to say "Hey, I think this idea X should be implemented and I'm starting work on it. My general plan is Y, any feedback
   is appreciated." This will allow other devs to potentially save you time by not accidentially duplicating work etc...
@@ -12,17 +12,4 @@
 - If your PR fixes a bug, mention "fixes #bugnum" somewhere in your pull request description.
 - If your other co-developers have comments on your PR please tweak as needed.
 - Please also enable "Allow edits by maintainers".
-- Please do not submit untested code.
-- If you do not have the affected hardware to test your code changes adequately against regressions, please indicate this, so that contributors and commnunity members can help test your changes.
 - If your PR gets accepted you can request a "Contributor" role in the Meshtastic Discord
-
-## 🤝 Attestations
-
-- [ ] I have tested that my proposed changes behave as described.
-- [ ] I have tested that my proposed changes do not cause any obvious regressions on the following devices:
-  - [ ] Heltec (Lora32) V3
-  - [ ] LilyGo T-Deck
-  - [ ] LilyGo T-Beam
-  - [ ] RAK WisBlock 4631
-  - [ ] Seeed Studio T-1000E tracker card
-  - [ ] Other (please specify below)

.github/workflows/build_esp32.yml

@@ -11,30 +11,27 @@ permissions: read-all
 
 jobs:
   build-esp32:
-    runs-on: ubuntu-24.04
+    runs-on: ubuntu-latest
     steps:
       - uses: actions/checkout@v4
 
-      - name: Get release version string
-        shell: bash
-        run: echo "long=$(./bin/buildinfo.py long)" >> $GITHUB_OUTPUT
-        id: version
-
       - name: Build ESP32
         id: build
-        uses: meshtastic/gh-action-firmware@main
+        uses: ./.github/actions/build-variant
         with:
-          pio_platform: esp32
-          pio_env: ${{ inputs.board }}
-          pio_target: build
-          ota_firmware_source: firmware.bin
-          ota_firmware_target: release/bleota.bin
-
-      - name: Store binaries as an artifact
-        uses: actions/upload-artifact@v4
-        with:
-          name: firmware-esp32-${{ inputs.board }}-${{ steps.version.outputs.long }}.zip
-          overwrite: true
-          path: |
+          github_token: ${{ secrets.GITHUB_TOKEN }}
+          board: ${{ inputs.board }}
+          remove-debug-flags: >-
+            ./arch/esp32/esp32.ini
+            ./arch/esp32/esp32s2.ini
+            ./arch/esp32/esp32s3.ini
+            ./arch/esp32/esp32c3.ini
+            ./arch/esp32/esp32c6.ini
+          build-script-path: bin/build-esp32.sh
+          ota-firmware-source: firmware.bin
+          ota-firmware-target: release/bleota.bin
+          artifact-paths: |
             release/*.bin
             release/*.elf
+          include-web-ui: true
+          arch: esp32

.github/workflows/build_esp32_c3.yml

@@ -11,30 +11,27 @@ permissions: read-all
 
 jobs:
   build-esp32-c3:
-    runs-on: ubuntu-24.04
+    runs-on: ubuntu-latest
     steps:
       - uses: actions/checkout@v4
 
-      - name: Get release version string
-        shell: bash
-        run: echo "long=$(./bin/buildinfo.py long)" >> $GITHUB_OUTPUT
-        id: version
-
       - name: Build ESP32-C3
         id: build
-        uses: meshtastic/gh-action-firmware@main
+        uses: ./.github/actions/build-variant
         with:
-          pio_platform: esp32
-          pio_env: ${{ inputs.board }}
-          pio_target: build
-          ota_firmware_source: firmware-c3.bin
-          ota_firmware_target: release/bleota-c3.bin
-
-      - name: Store binaries as an artifact
-        uses: actions/upload-artifact@v4
-        with:
-          name: firmware-esp32c3-${{ inputs.board }}-${{ steps.version.outputs.long }}.zip
-          overwrite: true
-          path: |
+          github_token: ${{ secrets.GITHUB_TOKEN }}
+          board: ${{ inputs.board }}
+          remove-debug-flags: >-
+            ./arch/esp32/esp32.ini
+            ./arch/esp32/esp32s2.ini
+            ./arch/esp32/esp32s3.ini
+            ./arch/esp32/esp32c3.ini
+            ./arch/esp32/esp32c6.ini
+          build-script-path: bin/build-esp32.sh
+          ota-firmware-source: firmware-c3.bin
+          ota-firmware-target: release/bleota-c3.bin
+          artifact-paths: |
             release/*.bin
             release/*.elf
+          include-web-ui: true
+          arch: esp32c3

.github/workflows/build_esp32_c6.yml

@@ -11,30 +11,27 @@ permissions: read-all
 
 jobs:
   build-esp32-c6:
-    runs-on: ubuntu-24.04
+    runs-on: ubuntu-latest
     steps:
       - uses: actions/checkout@v4
 
-      - name: Get release version string
-        shell: bash
-        run: echo "long=$(./bin/buildinfo.py long)" >> $GITHUB_OUTPUT
-        id: version
-
       - name: Build ESP32-C6
         id: build
-        uses: meshtastic/gh-action-firmware@main
+        uses: ./.github/actions/build-variant
         with:
-          pio_platform: esp32
-          pio_env: ${{ inputs.board }}
-          pio_target: build
-          ota_firmware_source: firmware-c3.bin
-          ota_firmware_target: release/bleota-c3.bin
-
-      - name: Store binaries as an artifact
-        uses: actions/upload-artifact@v4
-        with:
-          name: firmware-esp32c6-${{ inputs.board }}-${{ steps.version.outputs.long }}.zip
-          overwrite: true
-          path: |
+          github_token: ${{ secrets.GITHUB_TOKEN }}
+          board: ${{ inputs.board }}
+          remove-debug-flags: >-
+            ./arch/esp32/esp32.ini
+            ./arch/esp32/esp32s2.ini
+            ./arch/esp32/esp32s3.ini
+            ./arch/esp32/esp32c3.ini
+            ./arch/esp32/esp32c6.ini
+          build-script-path: bin/build-esp32.sh
+          ota-firmware-source: firmware-c3.bin
+          ota-firmware-target: release/bleota-c3.bin
+          artifact-paths: |
             release/*.bin
             release/*.elf
+          include-web-ui: true
+          arch: esp32c6

.github/workflows/build_esp32_s3.yml

@@ -11,30 +11,27 @@ permissions: read-all
 
 jobs:
   build-esp32-s3:
-    runs-on: ubuntu-24.04
+    runs-on: ubuntu-latest
     steps:
       - uses: actions/checkout@v4
 
-      - name: Get release version string
-        shell: bash
-        run: echo "long=$(./bin/buildinfo.py long)" >> $GITHUB_OUTPUT
-        id: version
-
       - name: Build ESP32-S3
         id: build
-        uses: meshtastic/gh-action-firmware@main
+        uses: ./.github/actions/build-variant
         with:
-          pio_platform: esp32
-          pio_env: ${{ inputs.board }}
-          pio_target: build
-          ota_firmware_source: firmware-s3.bin
-          ota_firmware_target: release/bleota-s3.bin
-
-      - name: Store binaries as an artifact
-        uses: actions/upload-artifact@v4
-        with:
-          name: firmware-esp32s3-${{ inputs.board }}-${{ steps.version.outputs.long }}.zip
-          overwrite: true
-          path: |
+          github_token: ${{ secrets.GITHUB_TOKEN }}
+          board: ${{ inputs.board }}
+          remove-debug-flags: >-
+            ./arch/esp32/esp32.ini
+            ./arch/esp32/esp32s2.ini
+            ./arch/esp32/esp32s3.ini
+            ./arch/esp32/esp32c3.ini
+            ./arch/esp32/esp32c6.ini
+          build-script-path: bin/build-esp32.sh
+          ota-firmware-source: firmware-s3.bin
+          ota-firmware-target: release/bleota-s3.bin
+          artifact-paths: |
             release/*.bin
             release/*.elf
+          include-web-ui: true
+          arch: esp32s3

.github/workflows/build_nrf52.yml

@@ -11,30 +11,20 @@ permissions: read-all
 
 jobs:
   build-nrf52:
-    runs-on: ubuntu-24.04
+    runs-on: ubuntu-latest
     steps:
       - uses: actions/checkout@v4
 
-      - name: Get release version string
-        shell: bash
-        run: echo "long=$(./bin/buildinfo.py long)" >> $GITHUB_OUTPUT
-        id: version
-
       - name: Build NRF52
         id: build
-        uses: meshtastic/gh-action-firmware@main
+        uses: ./.github/actions/build-variant
         with:
-          pio_platform: nrf52
-          pio_env: ${{ inputs.board }}
-          pio_target: build
-
-      - name: Store binaries as an artifact
-        uses: actions/upload-artifact@v4
-        with:
-          name: firmware-nrf52840-${{ inputs.board }}-${{ steps.version.outputs.long }}.zip
-          overwrite: true
-          path: |
+          github_token: ${{ secrets.GITHUB_TOKEN }}
+          board: ${{ inputs.board }}
+          build-script-path: bin/build-nrf52.sh
+          artifact-paths: |
+            release/*.hex
             release/*.uf2
             release/*.elf
-            release/*.hex
-            release/*-ota.zip
+            release/*.zip
+          arch: nrf52840

.github/workflows/build_rpi2040.yml

@@ -11,28 +11,18 @@ permissions: read-all
 
 jobs:
   build-rpi2040:
-    runs-on: ubuntu-24.04
+    runs-on: ubuntu-latest
     steps:
       - uses: actions/checkout@v4
 
-      - name: Get release version string
-        shell: bash
-        run: echo "long=$(./bin/buildinfo.py long)" >> $GITHUB_OUTPUT
-        id: version
-
       - name: Build Raspberry Pi 2040
         id: build
-        uses: meshtastic/gh-action-firmware@main
+        uses: ./.github/actions/build-variant
         with:
-          pio_platform: rp2xx0
-          pio_env: ${{ inputs.board }}
-          pio_target: build
-
-      - name: Store binaries as an artifact
-        uses: actions/upload-artifact@v4
-        with:
-          name: firmware-rp2040-${{ inputs.board }}-${{ steps.version.outputs.long }}.zip
-          overwrite: true
-          path: |
+          github_token: ${{ secrets.GITHUB_TOKEN }}
+          board: ${{ inputs.board }}
+          build-script-path: bin/build-rpi2040.sh
+          artifact-paths: |
             release/*.uf2
             release/*.elf
+          arch: rp2040

.github/workflows/build_stm32.yml

@@ -11,29 +11,19 @@ permissions: read-all
 
 jobs:
   build-stm32:
-    runs-on: ubuntu-24.04
+    runs-on: ubuntu-latest
     steps:
       - uses: actions/checkout@v4
 
-      - name: Get release version string
-        shell: bash
-        run: echo "long=$(./bin/buildinfo.py long)" >> $GITHUB_OUTPUT
-        id: version
-
       - name: Build STM32WL
         id: build
-        uses: meshtastic/gh-action-firmware@main
+        uses: ./.github/actions/build-variant
         with:
-          pio_platform: stm32wl
-          pio_env: ${{ inputs.board }}
-          pio_target: build
-
-      - name: Store binaries as an artifact
-        uses: actions/upload-artifact@v4
-        with:
-          name: firmware-stm32-${{ inputs.board }}-${{ steps.version.outputs.long }}.zip
-          overwrite: true
-          path: |
+          github_token: ${{ secrets.GITHUB_TOKEN }}
+          board: ${{ inputs.board }}
+          build-script-path: bin/build-stm32.sh
+          artifact-paths: |
             release/*.hex
             release/*.bin
             release/*.elf
+          arch: stm32

.github/workflows/daily_packaging.yml

@@ -1,7 +1,7 @@
 name: Daily Packaging
 on:
   schedule:
-    - cron: 0 2 * * *
+    - cron: 0 9 * * *
   workflow_dispatch:
   push:
     branches:
@@ -30,7 +30,7 @@ jobs:
     strategy:
       fail-fast: false
       matrix:
-        series: [plucky, noble, jammy]
+        series: [plucky, oracular, noble, jammy]
     uses: ./.github/workflows/package_ppa.yml
     with:
       ppa_repo: ppa:meshtastic/daily

.github/workflows/docker_build.yml

@@ -26,11 +26,6 @@ on:
         required: false
         type: boolean
         default: false
-      pio_env:
-        description: PlatformIO environment to build
-        required: false
-        type: string
-        default: native
     outputs:
       digest:
         description: Digest of built image
@@ -95,5 +90,3 @@ jobs:
           push: ${{ inputs.push }}
           tags: ${{ steps.meta.outputs.tags }} # Tag is only meant to be consumed by the "manifest" job
           platforms: ${{ inputs.platform }}
-          build-args: |
-            PIO_ENV=${{ inputs.pio_env }}

.github/workflows/main_matrix.yml

@@ -5,20 +5,14 @@ concurrency:
 on:
   # # Triggers the workflow on push but only for the master branch
   push:
-    branches:
-      - master
-      - develop
-      - event/*
+    branches: [master, develop]
     paths-ignore:
       - "**.md"
       - version.properties
 
   # Note: This is different from "pull_request". Need to specify ref when doing checkouts.
   pull_request_target:
-    branches:
-      - master
-      - develop
-      - event/*
+    branches: [master, develop]
     paths-ignore:
       - "**.md"
       #- "**.yml"
@@ -38,12 +32,12 @@ jobs:
         name: Checkout base
       - id: jsonStep
         run: |
-          if [[ "$GITHUB_HEAD_REF" == "" ]]; then
+          if [[ "${{ github.head_ref }}" == "" ]]; then
             TARGETS=$(./bin/generate_ci_matrix.py ${{matrix.arch}})
           else  
             TARGETS=$(./bin/generate_ci_matrix.py ${{matrix.arch}} quick)
           fi
-          echo "Name: $GITHUB_REF_NAME Base: $GITHUB_BASE_REF Ref: $GITHUB_REF Targets: $TARGETS"
+          echo "Name: ${{ github.ref_name }} Base: ${{ github.base_ref }} } Ref: ${{ github.ref }} Targets: $TARGETS"
           echo "${{matrix.arch}}=$(jq -cn --argjson environments "$TARGETS" '{board: $environments}')" >> $GITHUB_OUTPUT
     outputs:
       esp32: ${{ steps.jsonStep.outputs.esp32 }}
@@ -135,7 +129,6 @@ jobs:
       board: ${{ matrix.board }}
 
   build-debian-src:
-    if: github.repository == 'meshtastic/firmware'
     uses: ./.github/workflows/build_debian_src.yml
     with:
       series: UNRELEASED
@@ -150,10 +143,9 @@ jobs:
     secrets: inherit
 
   test-native:
-    if: ${{ !contains(github.ref_name, 'event/') }}
     uses: ./.github/workflows/test_native.yml
 
-  docker-deb-amd64:
+  docker-debian-amd64:
     uses: ./.github/workflows/docker_build.yml
     with:
       distro: debian
@@ -161,16 +153,7 @@ jobs:
       runs-on: ubuntu-24.04
       push: false
 
-  docker-deb-amd64-tft:
-    uses: ./.github/workflows/docker_build.yml
-    with:
-      distro: debian
-      platform: linux/amd64
-      runs-on: ubuntu-24.04
-      push: false
-      pio_env: native-tft
-
-  docker-alp-amd64:
+  docker-alpine-amd64:
     uses: ./.github/workflows/docker_build.yml
     with:
       distro: alpine
@@ -178,16 +161,7 @@ jobs:
       runs-on: ubuntu-24.04
       push: false
 
-  docker-alp-amd64-tft:
-    uses: ./.github/workflows/docker_build.yml
-    with:
-      distro: alpine
-      platform: linux/amd64
-      runs-on: ubuntu-24.04
-      push: false
-      pio_env: native-tft
-
-  docker-deb-arm64:
+  docker-debian-arm64:
     uses: ./.github/workflows/docker_build.yml
     with:
       distro: debian
@@ -195,7 +169,7 @@ jobs:
       runs-on: ubuntu-24.04-arm
       push: false
 
-  docker-deb-armv7:
+  docker-debian-armv7:
     uses: ./.github/workflows/docker_build.yml
     with:
       distro: debian
@@ -203,6 +177,17 @@ jobs:
       runs-on: ubuntu-24.04-arm
       push: false
 
+  after-checks:
+    runs-on: ubuntu-latest
+    if: ${{ github.event_name != 'workflow_dispatch' }}
+    needs: [check]
+    steps:
+      - name: Checkout code
+        uses: actions/checkout@v4
+        with:
+          ref: ${{github.event.pull_request.head.ref}}
+          repository: ${{github.event.pull_request.head.repo.full_name}}
+
   gather-artifacts:
     permissions:
       contents: write
@@ -258,6 +243,7 @@ jobs:
             ./device-*.sh
             ./device-*.bat
             ./littlefs-*.bin
+            ./littlefswebui-*.bin
             ./bleota*bin
             ./Meshtastic_nRF52_factory_erase*.uf2
           retention-days: 30
@@ -346,7 +332,7 @@ jobs:
           merge-multiple: true
           path: ./output/pio-deps-native-tft
 
-      - name: Zip Linux sources
+      - name: Zip linux sources
         working-directory: output
         run: |
           zip -j -9 -r ./meshtasticd-${{ steps.version.outputs.deb }}-src.zip ./debian-src
@@ -356,9 +342,7 @@ jobs:
       - name: Display structure of downloaded files
         run: ls -lR
 
-      - name: Add Linux sources to GtiHub Release
-        # Only run when targeting master branch with workflow_dispatch
-        if: ${{ github.ref_name == 'master' }}
+      - name: Add linux sources to release
         run: |
           gh release upload v${{ steps.version.outputs.long }} ./output/meshtasticd-${{ steps.version.outputs.deb }}-src.zip
           gh release upload v${{ steps.version.outputs.long }} ./output/platformio-deps-native-tft-${{ steps.version.outputs.long }}.zip
@@ -416,53 +400,9 @@ jobs:
       - name: Display structure of downloaded files
         run: ls -lR
 
-      - name: Add bins and debug elfs to GitHub Release
-        # Only run when targeting master branch with workflow_dispatch
-        if: ${{ github.ref_name == 'master' }}
+      - name: Add bins and debug elfs to release
         run: |
           gh release upload v${{ steps.version.outputs.long }} ./firmware-${{matrix.arch}}-${{ steps.version.outputs.long }}.zip
           gh release upload v${{ steps.version.outputs.long }} ./debug-elfs-${{matrix.arch}}-${{ steps.version.outputs.long }}.zip
         env:
           GITHUB_TOKEN: ${{ secrets.GITHUB_TOKEN }}
-
-  publish-firmware:
-    runs-on: ubuntu-24.04
-    if: ${{ github.event_name == 'workflow_dispatch' }}
-    needs: [release-firmware]
-    env:
-      targets: esp32,esp32s3,esp32c3,esp32c6,nrf52840,rp2040,stm32
-    steps:
-      - name: Checkout
-        uses: actions/checkout@v4
-
-      - name: Setup Python
-        uses: actions/setup-python@v5
-        with:
-          python-version: 3.x
-
-      - name: Get release version string
-        run: echo "long=$(./bin/buildinfo.py long)" >> $GITHUB_OUTPUT
-        id: version
-
-      - uses: actions/download-artifact@v4
-        with:
-          pattern: firmware-{${{ env.targets }}}-${{ steps.version.outputs.long }}
-          merge-multiple: true
-          path: ./publish
-
-      - name: Publish firmware to meshtastic.github.io
-        uses: peaceiris/actions-gh-pages@v4
-        env:
-          # On event/* branches, use the event name as the destination prefix
-          DEST_PREFIX: ${{ contains(github.ref_name, 'event/') && format('{0}/', github.ref_name) || '' }}
-        with:
-          deploy_key: ${{ secrets.DIST_PAGES_DEPLOY_KEY }}
-          external_repository: meshtastic/meshtastic.github.io
-          publish_branch: master
-          publish_dir: ./publish
-          destination_dir: ${{ env.DEST_PREFIX }}firmware-${{ steps.version.outputs.long }}
-          keep_files: true
-          user_name: github-actions[bot]
-          user_email: github-actions[bot]@users.noreply.github.com
-          commit_message: ${{ steps.version.outputs.long }}
-          enable_jekyll: true

.github/workflows/nightly.yml

@@ -8,7 +8,6 @@ permissions: read-all
 
 jobs:
   trunk_check:
-    if: github.repository == 'meshtastic/firmware'
     name: Trunk Check and Upload
     runs-on: ubuntu-24.04
 
@@ -22,7 +21,6 @@ jobs:
           trunk-token: ${{ secrets.TRUNK_TOKEN }}
 
   trunk_upgrade:
-    if: github.repository == 'meshtastic/firmware'
     # See: https://github.com/trunk-io/trunk-action/blob/v1/readme.md#automatic-upgrades
     name: Trunk Upgrade (PR)
     runs-on: ubuntu-24.04

.github/workflows/release_channels.yml

@@ -20,7 +20,7 @@ jobs:
     strategy:
       fail-fast: false
       matrix:
-        series: [plucky, noble, jammy]
+        series: [plucky, oracular, noble, jammy]
     uses: ./.github/workflows/package_ppa.yml
     with:
       ppa_repo: |-
@@ -46,14 +46,11 @@ jobs:
 
   # Create a PR to bump version when a release is Published
   bump-version:
-    if: github.event.action == 'published'
+    if: ${{ github.event.release.published }}
     runs-on: ubuntu-latest
     permissions:
       pull-requests: write
       contents: write
-    defaults:
-      run:
-        shell: bash
     steps:
       - name: Checkout
         uses: actions/checkout@v4
@@ -63,45 +60,32 @@ jobs:
         with:
           python-version: 3.x
 
-      - name: Bump version.properties
+      - name: Get release version string
         run: |
-          # Bump version.properties
-          chmod +x ./bin/bump_version.py
-          ./bin/bump_version.py
+          echo "long=$(./bin/buildinfo.py long)" >> $GITHUB_OUTPUT
+          echo "deb=$(./bin/buildinfo.py deb)" >> $GITHUB_OUTPUT
+        id: version
+        env:
+          BUILD_LOCATION: local
 
-      - name: Get new release version string
-        run: |
-          echo "short=$(./bin/buildinfo.py short)" >> $GITHUB_OUTPUT
-        id: new_version
+      - name: Bump version.properties
+        run: >-
+          bin/bump_version.py
 
       - name: Ensure debian deps are installed
+        shell: bash
         run: |
           sudo apt-get update -y --fix-missing
           sudo apt-get install -y devscripts
 
       - name: Update debian changelog
-        run: |
-          # Update debian changelog
-          chmod +x ./debian/ci_changelog.sh
-          ./debian/ci_changelog.sh
+        run: >-
+          debian/ci_changelog.sh
 
-      - name: Bump org.meshtastic.meshtasticd.metainfo.xml
-        run: |
-          # Bump org.meshtastic.meshtasticd.metainfo.xml
-          pip install -r bin/bump_metainfo/requirements.txt -q
-          chmod +x ./bin/bump_metainfo/bump_metainfo.py
-          ./bin/bump_metainfo/bump_metainfo.py --file bin/org.meshtastic.meshtasticd.metainfo.xml "${{ steps.new_version.outputs.short }}"
-        env:
-          PIP_DISABLE_PIP_VERSION_CHECK: 1
-
-      - name: Create Bumps pull request
+      - name: Create version.properties pull request
         uses: peter-evans/create-pull-request@v7
         with:
-          base: ${{ github.event.repository.default_branch }}
-          branch: create-pull-request/bump-version
-          title: Bump release version
-          commit-message: automated bumps
+          title: Bump version.properties
           add-paths: |
             version.properties
             debian/changelog
-            bin/org.meshtastic.meshtasticd.metainfo.xml

.github/workflows/sec_sast_semgrep_cron.yml

@@ -13,8 +13,7 @@ permissions:
 
 jobs:
   semgrep-full:
-    if: github.repository == 'meshtastic/firmware'
-    runs-on: ubuntu-24.04
+    runs-on: ubuntu-22.04
     container:
       image: semgrep/semgrep
 

.github/workflows/sec_sast_semgrep_pull.yml

@@ -6,7 +6,7 @@ permissions: read-all
 
 jobs:
   semgrep-diff:
-    runs-on: ubuntu-24.04
+    runs-on: ubuntu-22.04
     container:
       image: semgrep/semgrep
 

.github/workflows/stale_bot.yml

@@ -11,7 +11,6 @@ permissions:
 
 jobs:
   stale_issues:
-    if: github.repository == 'meshtastic/firmware'
     name: Close Stale Issues
     runs-on: ubuntu-latest
 

.github/workflows/test_native.yml

@@ -143,7 +143,7 @@ jobs:
           merge-multiple: true
 
       - name: Test Report
-        uses: dorny/test-reporter@v2.1.1
+        uses: dorny/test-reporter@v2.0.0
         with:
           name: PlatformIO Tests
           path: testreport.xml

.github/workflows/tests.yml

@@ -5,18 +5,13 @@ on:
     - cron: 0 0 * * * # Run every day at midnight
   workflow_dispatch: {}
 
-permissions:
-  contents: read
-  actions: read
-  checks: write
+permissions: read-all
 
 jobs:
   native-tests:
-    if: github.repository == 'meshtastic/firmware'
     uses: ./.github/workflows/test_native.yml
 
   hardware-tests:
-    if: github.repository == 'meshtastic/firmware'
     runs-on: test-runner
     steps:
       - name: Checkout code
@@ -49,7 +44,7 @@ jobs:
       - name: Setup Node
         uses: actions/setup-node@v4
         with:
-          node-version: 22
+          node-version: 18
 
       - name: Setup pnpm
         uses: pnpm/action-setup@v4

.github/workflows/update_protobufs.yml

@@ -33,7 +33,6 @@ jobs:
       - name: Create pull request
         uses: peter-evans/create-pull-request@v7
         with:
-          branch: create-pull-request/update-protobufs
           title: Update protobufs and classes
           add-paths: |
             protobufs

.gitignore

@@ -37,7 +37,4 @@ release/
 .vscode/extensions.json
 /compile_commands.json
 src/mesh/raspihttp/certificate.pem
-src/mesh/raspihttp/private_key.pem
-
-# Ignore logo (set at build time with platformio-custom.py)
-data/boot/logo.*
+src/mesh/raspihttp/private_key.pem

.trunk/configs/.prettierignore

@@ -1 +0,0 @@
-renovate.json

.trunk/trunk.yaml

@@ -1,34 +1,34 @@
 version: 0.1
 cli:
-  version: 1.24.0
+  version: 1.22.11
 plugins:
   sources:
     - id: trunk
-      ref: v1.7.1
+      ref: v1.6.7
       uri: https://github.com/trunk-io/plugins
 lint:
   enabled:
-    - checkov@3.2.450
-    - renovate@41.29.1
-    - prettier@3.6.2
-    - trufflehog@3.89.2
-    - yamllint@1.37.1
-    - bandit@1.8.6
-    - trivy@0.64.1
+    - prettier@3.5.3
+    - trufflehog@3.88.17
+    - yamllint@1.36.0
+    - bandit@1.8.3
+    - checkov@3.2.386
+    - terrascan@1.19.9
+    - trivy@0.60.0
     - taplo@0.9.3
-    - ruff@0.12.2
+    - ruff@0.10.0
     - isort@6.0.1
-    - markdownlint@0.45.0
-    - oxipng@9.1.5
-    - svgo@4.0.0
+    - markdownlint@0.44.0
+    - oxipng@9.1.4
+    - svgo@3.3.2
     - actionlint@1.7.7
-    - flake8@7.3.0
+    - flake8@7.1.2
     - hadolint@2.12.1-beta
     - shfmt@3.6.0
     - shellcheck@0.10.0
     - black@25.1.0
     - git-diff-check
-    - gitleaks@8.27.2
+    - gitleaks@8.24.0
     - clang-format@16.0.3
   ignore:
     - linters: [ALL]
@@ -38,7 +38,7 @@ runtimes:
   enabled:
     - python@3.10.8
     - go@1.21.0
-    - node@22.16.0
+    - node@18.20.5
 actions:
   disabled:
     - trunk-announce

Dockerfile

@@ -1,20 +1,20 @@
+# trunk-ignore-all(terrascan/AC_DOCKER_0002): Known terrascan issue
 # trunk-ignore-all(trivy/DS002): We must run as root for this container
+# trunk-ignore-all(checkov/CKV_DOCKER_8): We must run as root for this container
 # trunk-ignore-all(hadolint/DL3002): We must run as root for this container
 # trunk-ignore-all(hadolint/DL3008): Do not pin apt package versions
 # trunk-ignore-all(hadolint/DL3013): Do not pin pip package versions
 
 FROM python:3.13-bookworm AS builder
-ARG PIO_ENV=native
 ENV DEBIAN_FRONTEND=noninteractive
 ENV TZ=Etc/UTC
 
 # Install Dependencies
 ENV PIP_ROOT_USER_ACTION=ignore
 RUN apt-get update && apt-get install --no-install-recommends -y \
-        curl wget g++ zip git ca-certificates pkg-config \
+        wget g++ zip git ca-certificates \
         libgpiod-dev libyaml-cpp-dev libbluetooth-dev libi2c-dev libuv1-dev \
-        libusb-1.0-0-dev libulfius-dev liborcania-dev libssl-dev \
-        libx11-dev libinput-dev libxkbcommon-x11-dev \
+        libusb-1.0-0-dev libulfius-dev liborcania-dev libssl-dev pkg-config \
     && apt-get clean && rm -rf /var/lib/apt/lists/* \
     && pip install --no-cache-dir -U platformio \
     && mkdir /tmp/firmware
@@ -24,26 +24,13 @@ WORKDIR /tmp/firmware
 COPY . /tmp/firmware
 
 # Build
-RUN bash ./bin/build-native.sh "$PIO_ENV" && \
+RUN bash ./bin/build-native.sh && \
     cp "/tmp/firmware/release/meshtasticd_linux_$(uname -m)" "/tmp/firmware/release/meshtasticd"
 
-# Fetch web assets
-RUN curl -L "https://github.com/meshtastic/web/releases/download/v$(cat /tmp/firmware/bin/web.version)/build.tar" -o /tmp/web.tar \
-    && mkdir -p /tmp/web \
-    && tar -xf /tmp/web.tar -C /tmp/web/ \
-    && gzip -dr /tmp/web \
-    && rm /tmp/web.tar
 
 ##### PRODUCTION BUILD #############
 
 FROM debian:bookworm-slim
-LABEL org.opencontainers.image.title="Meshtastic" \
-      org.opencontainers.image.description="Debian Meshtastic daemon and web interface" \
-      org.opencontainers.image.url="https://meshtastic.org" \
-      org.opencontainers.image.documentation="https://meshtastic.org/docs/" \
-      org.opencontainers.image.authors="Meshtastic" \
-      org.opencontainers.image.licenses="GPL-3.0-or-later" \
-      org.opencontainers.image.source="https://github.com/meshtastic/firmware/"
 ENV DEBIAN_FRONTEND=noninteractive
 ENV TZ=Etc/UTC
 
@@ -51,17 +38,14 @@ ENV TZ=Etc/UTC
 USER root
 
 RUN apt-get update && apt-get --no-install-recommends -y install \
-        libc-bin libc6 libgpiod2 libyaml-cpp0.7 libi2c0 libuv1 libusb-1.0-0-dev \
-        liborcania2.3 libulfius2.7 libssl3 \
-        libx11-6 libinput10 libxkbcommon-x11-0 \
+        libc-bin libc6 libgpiod2 libyaml-cpp0.7 libi2c0 libuv1 libusb-1.0-0-dev liborcania2.3 libulfius2.7 libssl3 \
     && apt-get clean && rm -rf /var/lib/apt/lists/* \
     && mkdir -p /var/lib/meshtasticd \
     && mkdir -p /etc/meshtasticd/config.d \
     && mkdir -p /etc/meshtasticd/ssl
 
 # Fetch compiled binary from the builder
-COPY --from=builder /tmp/firmware/release/meshtasticd /usr/bin/
-COPY --from=builder /tmp/web /usr/share/meshtasticd/
+COPY --from=builder /tmp/firmware/release/meshtasticd /usr/sbin/
 # Copy config templates
 COPY ./bin/config.d /etc/meshtasticd/available.d
 
@@ -70,9 +54,7 @@ VOLUME /var/lib/meshtasticd
 
 # Expose Meshtastic TCP API port from the host
 EXPOSE 4403
-# Expose Meshtastic Web UI port from the host
-EXPOSE 9443
 
-CMD [ "sh", "-cx", "meshtasticd --fsdir=/var/lib/meshtasticd" ]
+CMD [ "sh", "-cx", "meshtasticd -d /var/lib/meshtasticd" ]
 
-HEALTHCHECK NONE
+HEALTHCHECK NONE

README.md

@@ -37,4 +37,3 @@ Join our community and help improve Meshtastic! 🚀
 ## Stats
 
 ![Alt](https://repobeats.axiom.co/api/embed/8025e56c482ec63541593cc5bd322c19d5c0bdcf.svg "Repobeats analytics image")
-

SECURITY.md

@@ -4,8 +4,8 @@
 
 | Firmware Version | Supported          |
 | ---------------- | ------------------ |
-| 2.6.x            | :white_check_mark: |
-| <= 2.5.x         | :x:                |
+| 2.5.x            | :white_check_mark: |
+| <= 2.4.x         | :x:                |
 
 ## Reporting a Vulnerability
 

alpine.Dockerfile

@@ -1,16 +1,15 @@
 # trunk-ignore-all(trivy/DS002): We must run as root for this container
+# trunk-ignore-all(checkov/CKV_DOCKER_8): We must run as root for this container
 # trunk-ignore-all(hadolint/DL3002): We must run as root for this container
 # trunk-ignore-all(hadolint/DL3018): Do not pin apk package versions
 # trunk-ignore-all(hadolint/DL3013): Do not pin pip package versions
 
-FROM python:3.13-alpine3.22 AS builder
-ARG PIO_ENV=native
-ENV PIP_ROOT_USER_ACTION=ignore
+FROM python:3.13-alpine3.21 AS builder
 
+ENV PIP_ROOT_USER_ACTION=ignore
 RUN apk --no-cache add \
         bash g++ libstdc++-dev linux-headers zip git ca-certificates libgpiod-dev yaml-cpp-dev bluez-dev \
         libusb-dev i2c-tools-dev libuv-dev openssl-dev pkgconf argp-standalone \
-        libx11-dev libinput-dev libxkbcommon-dev \
     && rm -rf /var/cache/apk/* \
     && pip install --no-cache-dir -U platformio \
     && mkdir /tmp/firmware
@@ -22,35 +21,23 @@ COPY . /tmp/firmware
 # Add `argp` for musl
 ENV PLATFORMIO_BUILD_FLAGS="-Os -ffunction-sections -fdata-sections -Wl,--gc-sections -largp"
 
-RUN bash ./bin/build-native.sh "$PIO_ENV" && \
+RUN bash ./bin/build-native.sh && \
     cp "/tmp/firmware/release/meshtasticd_linux_$(uname -m)" "/tmp/firmware/release/meshtasticd"
 
 # ##### PRODUCTION BUILD #############
 
-FROM alpine:3.22
-LABEL org.opencontainers.image.title="Meshtastic" \
-      org.opencontainers.image.description="Alpine Meshtastic daemon" \
-      org.opencontainers.image.url="https://meshtastic.org" \
-      org.opencontainers.image.documentation="https://meshtastic.org/docs/" \
-      org.opencontainers.image.authors="Meshtastic" \
-      org.opencontainers.image.licenses="GPL-3.0-or-later" \
-      org.opencontainers.image.source="https://github.com/meshtastic/firmware/"
+FROM alpine:3.21
 
 # nosemgrep: dockerfile.security.last-user-is-root.last-user-is-root
 USER root
 
 RUN apk --no-cache add \
-        shadow libstdc++ libgpiod yaml-cpp libusb i2c-tools libuv \
-        libx11 libinput libxkbcommon \
+        libstdc++ libgpiod yaml-cpp libusb i2c-tools libuv \
     && rm -rf /var/cache/apk/* \
     && mkdir -p /var/lib/meshtasticd \
     && mkdir -p /etc/meshtasticd/config.d \
     && mkdir -p /etc/meshtasticd/ssl
-
-# Fetch compiled binary from the builder
-COPY --from=builder /tmp/firmware/release/meshtasticd /usr/bin/
-# Copy config templates
-COPY ./bin/config.d /etc/meshtasticd/available.d
+COPY --from=builder /tmp/firmware/release/meshtasticd /usr/sbin/
 
 WORKDIR /var/lib/meshtasticd
 VOLUME /var/lib/meshtasticd

arch/esp32/esp32.ini

@@ -2,9 +2,7 @@
 [esp32_base]
 extends = arduino_base
 custom_esp32_kind = esp32
-platform =
-  # renovate: datasource=custom.pio depName=platformio/espressif32 packageName=platformio/platform/espressif32
-  platformio/espressif32@6.11.0
+platform = platformio/espressif32@6.10.0
 
 build_src_filter = 
   ${arduino_base.build_src_filter} -<platform/nrf52/> -<platform/stm32wl> -<platform/rp2xx0> -<mesh/eth/> -<mesh/raspihttp>
@@ -46,20 +44,13 @@ lib_deps =
   ${arduino_base.lib_deps}
   ${networking_base.lib_deps}
   ${environmental_base.lib_deps}
-  ${environmental_extra.lib_deps}
   ${radiolib_base.lib_deps}
-  # renovate: datasource=git-refs depName=meshtastic-esp32_https_server packageName=https://github.com/meshtastic/esp32_https_server gitBranch=master
-  https://github.com/meshtastic/esp32_https_server/archive/3223704846752e6d545139204837bdb2a55459ca.zip
-  # renovate: datasource=custom.pio depName=NimBLE-Arduino packageName=h2zero/library/NimBLE-Arduino
+  https://github.com/meshtastic/esp32_https_server.git#23665b3adc080a311dcbb586ed5941b5f94d6ea2
   h2zero/NimBLE-Arduino@^1.4.3
-  # renovate: datasource=git-refs depName=libpax packageName=https://github.com/dbinfrago/libpax gitBranch=master
-  https://github.com/dbinfrago/libpax/archive/3cdc0371c375676a97967547f4065607d4c53fd1.zip
-  # renovate: datasource=custom.pio depName=XPowersLib packageName=lewisxhe/library/XPowersLib
-  lewisxhe/XPowersLib@0.3.0
-  # renovate: datasource=git-refs depName=meshtastic-ESP32_Codec2 packageName=https://github.com/meshtastic/ESP32_Codec2 gitBranch=master
-  https://github.com/meshtastic/ESP32_Codec2/archive/633326c78ac251c059ab3a8c430fcdf25b41672f.zip
-  # renovate: datasource=custom.pio depName=rweather/Crypto packageName=rweather/library/Crypto
-  rweather/Crypto@0.4.0
+  https://github.com/dbinfrago/libpax.git#3cdc0371c375676a97967547f4065607d4c53fd1
+  lewisxhe/XPowersLib@^0.2.7
+  https://github.com/meshtastic/ESP32_Codec2.git#633326c78ac251c059ab3a8c430fcdf25b41672f
+  rweather/Crypto@^0.4.0
 
 lib_ignore = 
   segger_rtt

arch/esp32/esp32c6.ini

@@ -1,8 +1,6 @@
 [esp32c6_base]
 extends = esp32_base
-platform =
-  # Do not renovate until we have switched to pioarduino tagged builds
-  https://github.com/Jason2866/platform-espressif32/archive/22faa566df8c789000f8136cd8d0aca49617af55.zip
+platform = https://github.com/Jason2866/platform-espressif32.git#22faa566df8c789000f8136cd8d0aca49617af55
 build_flags =
   ${arduino_base.build_flags}
   -Wall
@@ -25,14 +23,10 @@ lib_deps =
   ${arduino_base.lib_deps}
   ${networking_base.lib_deps}
   ${environmental_base.lib_deps}
-  ${environmental_extra.lib_deps}
   ${radiolib_base.lib_deps}
-  # renovate: datasource=custom.pio depName=XPowersLib packageName=lewisxhe/library/XPowersLib
-  lewisxhe/XPowersLib@0.3.0
-  # renovate: datasource=git-refs depName=meshtastic-ESP32_Codec2 packageName=https://github.com/meshtastic/ESP32_Codec2 gitBranch=master
-  https://github.com/meshtastic/ESP32_Codec2/archive/633326c78ac251c059ab3a8c430fcdf25b41672f.zip
-  # renovate: datasource=custom.pio depName=rweather/Crypto packageName=rweather/library/Crypto
-  rweather/Crypto@0.4.0
+  lewisxhe/XPowersLib@^0.2.7
+  https://github.com/meshtastic/ESP32_Codec2.git#633326c78ac251c059ab3a8c430fcdf25b41672f
+  rweather/Crypto@^0.4.0
 
 build_src_filter = 
  ${esp32_base.build_src_filter} -<mesh/http> 

arch/esp32/esp32s2.ini

@@ -16,4 +16,4 @@ build_flags =
 lib_ignore = 
   ${esp32_base.lib_ignore} 
   NimBLE-Arduino
-  libpax
+  libpax

arch/esp32/esp32s3.ini

@@ -3,3 +3,4 @@ extends = esp32_base
 custom_esp32_kind = esp32s3
 
 monitor_speed = 115200
+

arch/nrf52/nrf52.ini

@@ -1,14 +1,10 @@
 [nrf52_base]
 ; Instead of the standard nordicnrf52 platform, we use our fork which has our added variant files
-platform =
-  # renovate: datasource=custom.pio depName=platformio/nordicnrf52 packageName=platformio/platform/nordicnrf52
-  platformio/nordicnrf52@^10.8.0
+platform = platformio/nordicnrf52@^10.7.0
 extends = arduino_base
 platform_packages =
   ; our custom Git version until they merge our PR
-  # TODO renovate
-  platformio/framework-arduinoadafruitnrf52 @ https://github.com/meshtastic/Adafruit_nRF52_Arduino#e13f5820002a4fb2a5e6754b42ace185277e5adf
-  ; Don't renovate toolchain-gccarmnoneeabi
+  platformio/framework-arduinoadafruitnrf52 @ https://github.com/meshtastic/Adafruit_nRF52_Arduino.git#e13f5820002a4fb2a5e6754b42ace185277e5adf
   platformio/toolchain-gccarmnoneeabi@~1.90301.0
 
 build_type = debug
@@ -21,6 +17,7 @@ build_flags =
   -DLFS_NO_ASSERT                      ; Disable LFS assertions , see https://github.com/meshtastic/firmware/pull/3818
   -DMESHTASTIC_EXCLUDE_AUDIO=1
   -DMESHTASTIC_EXCLUDE_PAXCOUNTER=1
+  -DMAX_NUM_NODES=80
 
 build_src_filter = 
   ${arduino_base.build_src_filter} -<platform/esp32/> -<platform/stm32wl> -<nimble/> -<mesh/wifi/> -<mesh/api/> -<mesh/http/> -<modules/esp32> -<platform/rp2xx0> -<mesh/eth/> -<mesh/raspihttp>
@@ -28,9 +25,8 @@ build_src_filter =
 lib_deps=
   ${arduino_base.lib_deps}
   ${radiolib_base.lib_deps}
-  # renovate: datasource=custom.pio depName=rweather/Crypto packageName=rweather/library/Crypto
-  rweather/Crypto@0.4.0
+  rweather/Crypto@^0.4.0
 
 lib_ignore =
   BluetoothOTA
-  lvgl
+  lvgl

arch/nrf52/nrf52840.ini

@@ -6,9 +6,7 @@ build_flags = ${nrf52_base.build_flags}
 lib_deps =
   ${nrf52_base.lib_deps}
   ${environmental_base.lib_deps}
-  ${environmental_extra.lib_deps}
-  # renovate: datasource=git-refs depName=Kongduino-Adafruit_nRFCrypto packageName=https://github.com/Kongduino/Adafruit_nRFCrypto gitBranch=master
-  https://github.com/Kongduino/Adafruit_nRFCrypto/archive/5f838d2709461a2c981f642917aa50254a25c14c.zip
+  https://github.com/Kongduino/Adafruit_nRFCrypto.git#e31a8825ea3300b163a0a3c1ddd5de34e10e1371
 
 ; Common NRF52 debugging settings follow.  See the Meshtastic developer docs for how to connect SWD debugging probes to your board.
 

arch/portduino/portduino.ini

@@ -1,8 +1,6 @@
 ; The Portduino based 'native' environment. Currently supported on Linux targets with real LoRa hardware (or simulated).
 [portduino_base]
-platform =
-  # renovate: datasource=git-refs depName=platform-native packageName=https://github.com/meshtastic/platform-native gitBranch=develop
-  https://github.com/meshtastic/platform-native/archive/6cb7a455b440dd0738e8ed74a18136ed5cf7ea63.zip
+platform = https://github.com/Jorropo/platform-native.git#17fa89daec4402af491512f75278a7fec8a5818c
 framework = arduino
 
 build_src_filter = 
@@ -17,21 +15,18 @@ build_src_filter =
   +<mesh/raspihttp/>
   -<mesh/eth/>
   -<modules/esp32>
+  -<modules/Telemetry/EnvironmentTelemetry.cpp>
+  -<modules/Telemetry/AirQualityTelemetry.cpp>
+  -<modules/Telemetry/Sensor>
   +<../variants/portduino>
 
 lib_deps =
   ${env.lib_deps}
   ${networking_base.lib_deps}
   ${radiolib_base.lib_deps}
-  ${environmental_base.lib_deps}
-  # renovate: datasource=custom.pio depName=rweather/Crypto packageName=rweather/library/Crypto
-  rweather/Crypto@0.4.0
-  # renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
+  rweather/Crypto@^0.4.0
   lovyan03/LovyanGFX@^1.2.0
-  # renovate: datasource=git-refs depName=libch341-spi-userspace packageName=https://github.com/pine64/libch341-spi-userspace gitBranch=main
-  https://github.com/pine64/libch341-spi-userspace/archive/af9bc27c9c30fa90772279925b7c5913dff789b4.zip
-  # renovate: datasource=custom.pio depName=adafruit/Adafruit seesaw Library packageName=adafruit/library/Adafruit seesaw Library
-	adafruit/Adafruit seesaw Library@1.7.9
+  https://github.com/pine64/libch341-spi-userspace#a9b17e3452f7fb747000d9b4ad4409155b39f6ef
 
 build_flags =
   ${arduino_base.build_flags}
@@ -47,10 +42,4 @@ build_flags =
   -lyaml-cpp
   -li2c
   -luv
-  -std=gnu17
   -std=c++17
-
-lib_ignore =
-  Adafruit NeoPixel
-  Adafruit ST7735 and ST7789 Library
-  SD

arch/rp2xx0/rp2040.ini

@@ -1,13 +1,8 @@
 ; Common settings for rp2040 Processor based targets
 [rp2040_base]
-platform =
-  # TODO renovate
-  https://github.com/maxgerhardt/platform-raspberrypi#76ecf3c7e9dd4503af0331154c4ca1cddc4b03e5
-  ; For arduino-pico >= 4.4.3
+platform = https://github.com/maxgerhardt/platform-raspberrypi.git#76ecf3c7e9dd4503af0331154c4ca1cddc4b03e5 ; For arduino-pico >= 4.4.3
 extends = arduino_base
-platform_packages =
-  # TODO renovate
-  framework-arduinopico@https://github.com/earlephilhower/arduino-pico#4.4.3
+platform_packages = framework-arduinopico@https://github.com/earlephilhower/arduino-pico.git#4.4.3
 
 board_build.core = earlephilhower
 board_build.filesystem_size = 0.5m
@@ -28,7 +23,5 @@ lib_ignore =
 lib_deps =
   ${arduino_base.lib_deps}
   ${environmental_base.lib_deps}
-  ${environmental_extra.lib_deps}
   ${radiolib_base.lib_deps}
-  # renovate: datasource=custom.pio depName=rweather/Crypto packageName=rweather/library/Crypto
-  rweather/Crypto@0.4.0
+  rweather/Crypto

arch/rp2xx0/rp2350.ini

@@ -1,13 +1,8 @@
-; Common settings for rp2350 Processor based targets
+; Common settings for rp2040 Processor based targets
 [rp2350_base]
-platform =
-  # TODO renovate
-  https://github.com/maxgerhardt/platform-raspberrypi#76ecf3c7e9dd4503af0331154c4ca1cddc4b03e5
-  ; For arduino-pico >= 4.4.3
+platform = https://github.com/maxgerhardt/platform-raspberrypi.git#76ecf3c7e9dd4503af0331154c4ca1cddc4b03e5 ; For arduino-pico >= 4.4.3
 extends = arduino_base
-platform_packages =
-  # TODO renovate
-  framework-arduinopico@https://github.com/earlephilhower/arduino-pico#4.4.3
+platform_packages = framework-arduinopico@https://github.com/earlephilhower/arduino-pico.git#4.4.3
 
 board_build.core = earlephilhower
 board_build.filesystem_size = 0.5m
@@ -25,7 +20,5 @@ lib_ignore =
 lib_deps =
   ${arduino_base.lib_deps}
   ${environmental_base.lib_deps}
-  ${environmental_extra.lib_deps}
   ${radiolib_base.lib_deps}
-  # renovate: datasource=custom.pio depName=rweather/Crypto packageName=rweather/library/Crypto
-  rweather/Crypto@0.4.0
+  rweather/Crypto

arch/stm32/stm32.ini

@@ -1,50 +1,44 @@
 [stm32_base]
 extends = arduino_base
-platform =
-  # renovate: datasource=custom.pio depName=platformio/ststm32 packageName=platformio/platform/ststm32
-  platformio/ststm32@19.2.0
-platform_packages =
-  # TODO renovate
-  platformio/framework-arduinoststm32@https://github.com/stm32duino/Arduino_Core_STM32/archive/2.10.1.zip
-extra_scripts =
-  ${env.extra_scripts}
-  post:extra_scripts/extra_stm32.py
+platform = platformio/ststm32
+platform_packages = platformio/framework-arduinoststm32@^4.20900.0
 
 build_type = release
 
-build_flags =
+;board_build.flash_offset = 0x08000000
+
+build_flags = 
   ${arduino_base.build_flags}
   -flto
   -Isrc/platform/stm32wl -g
-  -DMESHTASTIC_EXCLUDE_AUDIO=1
-  -DMESHTASTIC_EXCLUDE_ATAK=1 ; ATAK is quite big, disable it for big flash savings.
-  -DMESHTASTIC_EXCLUDE_INPUTBROKER=1
-  -DMESHTASTIC_EXCLUDE_POWERMON=1
-  -DMESHTASTIC_EXCLUDE_SCREEN=1
-  -DMESHTASTIC_EXCLUDE_MQTT=1
-  -DMESHTASTIC_EXCLUDE_BLUETOOTH=1
-  -DMESHTASTIC_EXCLUDE_GPS=1
-  -DMESHTASTIC_EXCLUDE_WIFI=1
-  -DMESHTASTIC_EXCLUDE_TZ=1 ; Exclude TZ to save some flash space.
-  -DPIO_FRAMEWORK_ARDUINO_NANOLIB_FLOAT_PRINTF ; This is REQUIRED for at least traceroute debug prints - without it the length ends up uninitialized.
-  ;-DDEBUG_MUTE
+  -DMESHTASTIC_EXCLUDE_ENVIRONMENTAL_SENSOR
+  -DMESHTASTIC_EXCLUDE_INPUTBROKER
+  -DMESHTASTIC_EXCLUDE_I2C
+  -DMESHTASTIC_EXCLUDE_POWERMON
+  -DMESHTASTIC_EXCLUDE_SCREEN
+  -DMESHTASTIC_EXCLUDE_MQTT
+  -DMESHTASTIC_EXCLUDE_BLUETOOTH
+  -DMESHTASTIC_EXCLUDE_PKI
+  -DMESHTASTIC_EXCLUDE_GPS
+;  -DVECT_TAB_OFFSET=0x08000000
+  -DconfigUSE_CMSIS_RTOS_V2=1
+;  -DSPI_MODE_0=SPI_MODE0
   -fmerge-all-constants
   -ffunction-sections
   -fdata-sections
-
-build_src_filter =
+  
+build_src_filter = 
   ${arduino_base.build_src_filter} -<platform/esp32/> -<nimble/> -<mesh/api/> -<mesh/wifi/> -<mesh/http/> -<modules/esp32> -<mesh/eth/> -<input> -<buzz> -<modules/RemoteHardwareModule.cpp> -<platform/nrf52> -<platform/portduino> -<platform/rp2xx0> -<mesh/raspihttp>
 
 board_upload.offset_address = 0x08000000
 upload_protocol = stlink
-debug_tool = stlink
 
 lib_deps =
   ${env.lib_deps}
-  ${radiolib_base.lib_deps}
-
-  # renovate: datasource=git-refs depName=caveman99-stm32-Crypto packageName=https://github.com/caveman99/Crypto gitBranch=main
-  https://github.com/caveman99/Crypto/archive/eae9c768054118a9399690f8af202853d1ae8516.zip
+  charlesbaynham/OSFS@^1.2.3
+  jgromes/RadioLib@7.0.2
+  https://github.com/caveman99/Crypto.git#f61ae26a53f7a2d0ba5511625b8bf8eff3a35d5e
 
 lib_ignore =
-  OneButton
+  mathertel/OneButton@2.6.1
+  Wire

bin/99-meshtasticd-udev.rules

@@ -1,7 +0,0 @@
-# Set spidev ownership to 'spi' group
-SUBSYSTEM=="spidev", KERNEL=="spidev*", GROUP="spi", MODE="0660"
-# Allow access to USB CH341 devices
-SUBSYSTEM=="usb", ATTRS{idVendor}=="1a86", ATTRS{idProduct}=="5512", MODE="0666"
-# Set gpio ownership to 'gpio' group
-SUBSYSTEM=="*gpiomem*", GROUP="gpio", MODE="0660"
-SUBSYSTEM=="gpio", GROUP="gpio", MODE="0660"

bin/build-esp32.sh

@@ -11,7 +11,7 @@ rm -f $OUTDIR/firmware*
 rm -r $OUTDIR/* || true
 
 # Important to pull latest version of libs into all device flavors, otherwise some devices might be stale
-platformio pkg install -e $1
+platformio pkg update -e $1
 
 echo "Building for $1 with $PLATFORMIO_BUILD_FLAGS"
 rm -f .pio/build/$1/firmware.*
@@ -34,12 +34,11 @@ SRCBIN=.pio/build/$1/firmware.bin
 cp $SRCBIN $OUTDIR/$basename-update.bin
 
 echo "Building Filesystem for ESP32 targets"
-# If you want to build the webui, uncomment the following lines
-# pio run --environment $1 -t buildfs
-# cp .pio/build/$1/littlefs.bin $OUTDIR/littlefswebui-$1-$VERSION.bin
-# # Remove webserver files from the filesystem and rebuild
-# ls -l data/static # Diagnostic list of files
-# rm -rf data/static
+pio run --environment $1 -t buildfs
+cp .pio/build/$1/littlefs.bin $OUTDIR/littlefswebui-$1-$VERSION.bin
+# Remove webserver files from the filesystem and rebuild
+ls -l data/static # Diagnostic list of files
+rm -rf data/static
 pio run --environment $1 -t buildfs
 cp .pio/build/$1/littlefs.bin $OUTDIR/littlefs-$1-$VERSION.bin
 cp bin/device-install.* $OUTDIR

bin/build-native.sh

@@ -15,7 +15,6 @@ platformioFailed() {
 
 VERSION=$(bin/buildinfo.py long)
 SHORT_VERSION=$(bin/buildinfo.py short)
-PIO_ENV=${1:-native}
 
 OUTDIR=release/
 
@@ -25,7 +24,7 @@ mkdir -p $OUTDIR/
 rm -r $OUTDIR/* || true
 
 # Important to pull latest version of libs into all device flavors, otherwise some devices might be stale
-pio pkg install --environment "$PIO_ENV" || platformioFailed
-pio run --environment "$PIO_ENV" || platformioFailed
-cp ".pio/build/$PIO_ENV/program" "$OUTDIR/meshtasticd_linux_$(uname -m)"
+pio pkg update --environment native || platformioFailed
+pio run --environment native || platformioFailed
+cp .pio/build/native/program "$OUTDIR/meshtasticd_linux_$(uname -m)"
 cp bin/native-install.* $OUTDIR

bin/build-nrf52.sh

@@ -11,7 +11,7 @@ rm -f $OUTDIR/firmware*
 rm -r $OUTDIR/* || true
 
 # Important to pull latest version of libs into all device flavors, otherwise some devices might be stale
-platformio pkg install -e $1
+platformio pkg update -e $1
 
 echo "Building for $1 with $PLATFORMIO_BUILD_FLAGS"
 rm -f .pio/build/$1/firmware.*

bin/build-rpi2040.sh

@@ -11,7 +11,7 @@ rm -f $OUTDIR/firmware*
 rm -r $OUTDIR/* || true
 
 # Important to pull latest version of libs into all device flavors, otherwise some devices might be stale
-platformio pkg install -e $1
+platformio pkg update -e $1
 
 echo "Building for $1 with $PLATFORMIO_BUILD_FLAGS"
 rm -f .pio/build/$1/firmware.*

bin/build-stm32.sh

@@ -11,7 +11,7 @@ rm -f $OUTDIR/firmware*
 rm -r $OUTDIR/* || true
 
 # Important to pull latest version of libs into all device flavors, otherwise some devices might be stale
-platformio pkg install -e $1
+platformio pkg update -e $1
 
 echo "Building for $1 with $PLATFORMIO_BUILD_FLAGS"
 rm -f .pio/build/$1/firmware.*

bin/bump_metainfo/bump_metainfo.py

@@ -1,72 +0,0 @@
-#!/usr/bin/env python3
-import argparse
-import xml.etree.ElementTree as ET
-from defusedxml.ElementTree import parse
-from datetime import datetime, timezone
-
-
-# Indent by 2 spaces to align with xml formatting.
-def indent(elem, level=0):
-    i = "\n" + level * "  "
-    if len(elem):
-        if not elem.text or not elem.text.strip():
-            elem.text = i + "  "
-        for child in elem:
-            indent(child, level + 1)
-        if not child.tail or not child.tail.strip():
-            child.tail = i
-    if level and (not elem.tail or not elem.tail.strip()):
-        elem.tail = i
-
-
-def main():
-    parser = argparse.ArgumentParser(
-        description="Prepend new release entry to metainfo.xml file.")
-    parser.add_argument("--file", help="Path to the metainfo.xml file",
-                        default="org.meshtastic.meshtasticd.metainfo.xml")
-    parser.add_argument("version", help="Version string (e.g. 2.6.4)")
-    parser.add_argument("--date", help="Release date (YYYY-MM-DD), defaults to today",
-                        default=datetime.now(timezone.utc).date().isoformat())
-
-    args = parser.parse_args()
-
-    tree = parse(args.file)
-    root = tree.getroot()
-
-    releases = root.find('releases')
-    if releases is None:
-        raise RuntimeError("<releases> element not found in XML.")
-
-    existing_versions = {
-        release.get('version'): release
-        for release in releases.findall('release')
-    }
-    existing_release = existing_versions.get(args.version)
-
-    if existing_release is not None:
-        if not existing_release.get('date'):
-            print(f"Version {args.version} found without date. Adding date...")
-            existing_release.set('date', args.date)
-        else:
-            print(
-                f"Version {args.version} is already present with date, skipping insertion.")
-    else:
-        new_release = ET.Element('release', {
-            'version': args.version,
-            'date': args.date
-        })
-        url = ET.SubElement(new_release, 'url', {'type': 'details'})
-        url.text = f"https://github.com/meshtastic/firmware/releases?q=tag%3Av{args.version}"
-
-        releases.insert(0, new_release)
-
-        indent(releases, level=1)
-        releases.tail = "\n"
-
-        print(f"Inserted new release: {args.version}")
-
-    tree.write(args.file, encoding='UTF-8', xml_declaration=True)
-
-
-if __name__ == "__main__":
-    main()

bin/bump_metainfo/requirements.txt

@@ -1 +0,0 @@
-defusedxml==0.7.1

bin/check-all.sh

@@ -23,4 +23,4 @@ for BOARD in $BOARDS; do
 	CHECK="${CHECK} -e ${BOARD}"
 done
 
-pio check --flags "-DAPP_VERSION=${APP_VERSION} --suppressions-list=suppressions.txt --inline-suppr" $CHECK --skip-packages --pattern="src/" --fail-on-defect=medium --fail-on-defect=high
+pio check --flags "-DAPP_VERSION=${APP_VERSION} --suppressions-list=suppressions.txt" $CHECK --skip-packages --pattern="src/" --fail-on-defect=medium --fail-on-defect=high

bin/config-dist.yaml

@@ -6,12 +6,6 @@
 ### Including the "Module:" line!
 ---
 Lora:
-  # Default to auto-detecting the module type
-  # This will be overridden by configs from config.d
-  Module: auto
-
-#  # Uncomment to enable Simulation mode, or use --sim
-#  Module: sim
 
 #  Module: sx1262  # Waveshare SX1302 LISTEN ONLY AT THIS TIME!
 #  CS: 7
@@ -96,9 +90,9 @@ Lora:
 ### Some devices, like the pinedio, may require spidev0.1 as a workaround.
 #  spidev: spidev0.0
 
-### Deprecated location for User Button:
+### Define GPIO buttons here:
 
-#GPIO:
+GPIO:
 #  User: 6
 
 ### Define GPS
@@ -115,6 +109,17 @@ I2C:
 
 Display:
 
+### Waveshare 1.44inch LCD HAT
+#  Panel: ST7735S
+#  CS: 8         #Chip Select
+#  DC: 25        # Data/Command pin
+#  Backlight: 24
+#  Width: 128
+#  Height: 128
+#  Reset: 27
+#  OffsetX: 0
+#  OffsetY: 0
+
 ### Adafruit PiTFT 2.8 TFT+Touchscreen
 #  Panel: ILI9341
 #  CS: 8
@@ -169,16 +174,6 @@ Input:
 
 #  KeyboardDevice: /dev/input/by-id/usb-_Raspberry_Pi_Internal_Keyboard-event-kbd
 
-### Standard User Button Config
-#  UserButton: 6
-
-### Trackball/Joystick input
-#  TrackballUp: 6
-#  TrackballDown: 19
-#  TrackballLeft: 5
-#  TrackballRight: 26
-#  TrackballPress: 13
-
 ###
 
 Logging:
@@ -187,26 +182,14 @@ Logging:
 #  AsciiLogs: true     # default if not specified is !isatty() on stdout
 
 Webserver:
-#  Port: 9443 # Port for Webserver & Webservices
+#  Port: 443 # Port for Webserver & Webservices
 #  RootPath: /usr/share/meshtasticd/web # Root Dir of WebServer
 #  SSLKey: /etc/meshtasticd/ssl/private_key.pem # Path to SSL Key, generated if not present
 #  SSLCert: /etc/meshtasticd/ssl/certificate.pem # Path to SSL Certificate, generated if not present
 
-
-HostMetrics:
-#  ReportInterval: 30 # Interval in minutes between HostMetrics report packets, or 0 for disabled
-#  Channel: 0 # channel to send Host Metrics over. Defaults to the primary channel.
-#  UserStringCommand: cat /sys/firmware/devicetree/base/serial-number # Command to execute, to send the results as the userString
-
-
-Config:
-#  DisplayMode: TWOCOLOR # uncomment to force BaseUI
-#  DisplayMode: COLOR # uncomment to force MUI
-
 General:
   MaxNodes: 200
   MaxMessageQueue: 100
   ConfigDirectory: /etc/meshtasticd/config.d/
-  AvailableDirectory: /etc/meshtasticd/available.d/
 #  MACAddress: AA:BB:CC:DD:EE:FF
-#  MACAddressSource: eth0
+#  MACAddressSource: eth0

bin/config.d/display-waveshare-1-44.yaml

@@ -1,26 +0,0 @@
-### Waveshare 1.44inch LCD HAT
-Display:
-  Panel: ST7735S
-  spidev: spidev0.0  # Specify either the spidev here, or the CS below
-#  CS: 8         #Chip Select # Optional, as this is the default pin for spidev0.0
-  DC: 25        # Data/Command pin
-  Backlight: 24
-  Width: 128
-  Height: 128
-  Reset: 27
-  OffsetX: 2
-  OffsetY: 1
-
-
-#  OffsetY: 31  # These two options are used to properly flip the screen 180 degrees
-#  OffsetRotate: 3
-
-
-Input:
-  TrackballUp: 6
-  TrackballDown: 19
-  TrackballLeft: 5
-  TrackballRight: 26
-  TrackballPress: 13
-  TrackballDirection: FALLING
-#  User: 21

bin/config.d/lora-Adafruit-RFM9x

@@ -0,0 +1,5 @@
+#  Module: RF95  # Adafruit RFM9x
+#  Reset: 25
+#  CS: 7
+#  IRQ: 22
+#  Busy: 23

bin/config.d/lora-Adafruit-RFM9x.yaml

@@ -1,6 +0,0 @@
-Lora:
-  Module: RF95  # Adafruit RFM9x
-  Reset: 25
-  CS: 7
-  IRQ: 22
-#  Busy: 23

bin/config.d/lora-MeshAdv-900M30S.yaml

@@ -1,5 +1,3 @@
-# MeshAdv-Pi E22-900M30S
-# https://github.com/chrismyers2000/MeshAdv-Pi-Hat
 Lora:
   Module: sx1262
   CS: 21
@@ -11,4 +9,4 @@ Lora:
   DIO3_TCXO_VOLTAGE: true
   # Only for E22-900M33S:
   # Limit the output power to 8 dBm
-  # SX126X_MAX_POWER: 8
+  # SX126X_MAX_POWER: 8

bin/config.d/lora-MeshAdv-Mini-900M22S.yaml

@@ -1,11 +0,0 @@
-# MeshAdv Mini E22-900M22S
-# https://github.com/chrismyers2000/MeshAdv-Mini
-Lora:
-  Module: sx1262  # Ebyte E22-900M22S 
-  CS: 8
-  IRQ: 16
-  Busy: 20
-  Reset: 24
-  RXen: 12
-  DIO2_AS_RF_SWITCH: true
-  DIO3_TCXO_VOLTAGE: true

bin/config.d/lora-RAK6421.yaml

@@ -1,21 +0,0 @@
-Lora:
-
-  ### RAK13300in Slot 1
-  Module: sx1262
-  IRQ: 22 #IO6
-  Reset: 16 # IO4
-  Busy: 24 # IO5
-  # Ant_sw: 13 # IO3 
-  DIO3_TCXO_VOLTAGE: true
-  DIO2_AS_RF_SWITCH: true
-  spidev: spidev0.0
-  # CS: 8
-
-
-  ### RAK13300in Slot 2 pins
-#  IRQ: 18 #IO6
-#  Reset: 24 # IO4
-#  Busy: 19 # IO5
-#  # Ant_sw: 23 # IO3 
-#  spidev: spidev0.1
-#  # CS: 7

bin/config.d/lora-lyra-picocalc-wio-sx1262.yaml

@@ -1,18 +0,0 @@
-Lora:
-  Module: sx1262
-  DIO2_AS_RF_SWITCH: true
-  DIO3_TCXO_VOLTAGE: true
-  gpiochip: 0
-  MOSI: 12
-  MISO: 13
-  IRQ: 1
-  Busy: 23
-  Reset: 22
-  RXen: 0
-  gpiochip: 1
-  CS: 9
-  SCK: 11
-#  TXen: bridge to DIO2 on E22 module
-  SX126X_MAX_POWER: 22
-  spidev: spidev1.0
-  spiSpeed: 2000000

bin/config.d/lora-piggystick-lr1121.yaml

@@ -1,11 +0,0 @@
-Lora:
-  Module: lr1121
-  CS: 0
-  IRQ: 6
-  Reset: 2
-  Busy: 4
-  spidev: ch341
-  DIO3_TCXO_VOLTAGE: 1.8
-#  USB_Serialnum: 12345678
-  USB_PID: 0x5512
-  USB_VID: 0x1A86

bin/config.d/lora-usb-meshtoad-e22.yaml

@@ -1,17 +0,0 @@
-Lora:
-  Module: sx1262
-  CS: 0
-  IRQ: 6
-  Reset: 2
-  Busy: 4
-  RXen: 1
-  DIO2_AS_RF_SWITCH: true
-  DIO3_TCXO_VOLTAGE: true
-  spidev: ch341
-  USB_PID: 0x5512
-  USB_VID: 0x1A86
-  # Optional: Reduce power to 10 dBm to
-  # avoid over-drawing the USB port
-  # SX126X_MAX_POWER: 10
-  # Optional: Set the serial number for multi-radio support
-  # USB_Serialnum: 13374201

bin/config.d/lora-ws-raspberry-pico-to-orangepi-03.yaml

@@ -1,52 +0,0 @@
-# https://www.waveshare.com/pico-lora-sx1262-868m.htm
-# http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-Zero-3.html
-#
-# See Orange Pi Zero3 manual, chapter 3.16, page 124 for 26-pin header pinout
-#
-# Pin Connection
-# Waveshare       Orange Pi Zero3
-#   36    3.3V        17
-#   15    MOSI        19
-#   16    MISO        21  
-#   14    CLK         23
-#   38    GND         25
-#   4     BUSY        18
-#   20    RESET       22
-#   5     CS          24
-#   26    DIO1/IRQ    26
-
-Lora:
-  Module: sx1262  # Waveshare Raspberry Pico Lora module
-  DIO2_AS_RF_SWITCH: true
-  DIO3_TCXO_VOLTAGE: true
-  # Specify either the spidev1_1 or the CS below, not both!
-  # On DietPi Linux, when using the user overlay dietpi-spi1_1.dtbo, CS will be configured with spidev1.1
-  spidev: spidev1.1 # See Orange Pi Zero3 manual, chapter 3.18.3, page 130
-#  CS:             # CS     PIN_24 -> chip 1, line 233
-#    pin: 24
-#    gpiochip: 1
-#    line: 233
-  SCK:            # SCK     PIN_23 -> chip 1, line 230
-    pin: 23
-    gpiochip: 1
-    line: 230
-  Busy:           # BUSY    PIN_18 -> chip 1, line 78
-    pin: 18
-    gpiochip: 1
-    line: 78
-  MOSI:           # MOSI    PIN_19 -> chip 1, line 231
-    pin: 19
-    gpiochip: 1
-    line: 231
-  MISO:           # MISO    PIN_21 -> chip 1, line 232
-    pin: 21
-    gpiochip: 1
-    line: 232
-  Reset:          # NRST    PIN_22 -> chip 1, line 71
-    pin: 22
-    gpiochip: 1
-    line: 71
-  IRQ:            # DIO1    PIN_26 -> chip 1, line 74
-    pin: 26
-    gpiochip: 1
-    line: 74

bin/device-install.bat

@@ -5,26 +5,19 @@ TITLE Meshtastic device-install
 SET "SCRIPT_NAME=%~nx0"
 SET "DEBUG=0"
 SET "PYTHON="
+SET "WEB_APP=0"
 SET "TFT_BUILD=0"
-SET "BIGDB8=0"
-SET "BIGDB16=0"
+SET "TFT8=0"
+SET "TFT16=0"
 SET "ESPTOOL_BAUD=115200"
 SET "ESPTOOL_CMD="
 SET "LOGCOUNTER=0"
-SET "BPS_RESET=0"
-
-@REM FIXME: Determine mcu from PlatformIO variant, this is unmaintainable.
-SET "S3=s3 v3 t-deck wireless-paper wireless-tracker station-g2 unphone"
-SET "C3=esp32c3"
-@REM FIXME: Determine flash size from PlatformIO variant, this is unmaintainable.
-SET "BIGDB_8MB=picomputer-s3 unphone seeed-sensecap-indicator crowpanel-esp32s3 heltec_capsule_sensor_v3 heltec-v3 heltec-vision-master-e213 heltec-vision-master-e290 heltec-vision-master-t190 heltec-wireless-paper heltec-wireless-tracker heltec-wsl-v3 icarus seeed-xiao-s3 tbeam-s3-core tracksenger"
-SET "BIGDB_16MB=t-deck mesh-tab t-energy-s3 dreamcatcher ESP32-S3-Pico m5stack-cores3 station-g2 t-eth-elite t-watch-s3"
 
 GOTO getopts
 :help
 ECHO Flash image file to device, but first erasing and writing system information.
 ECHO.
-ECHO Usage: %SCRIPT_NAME% -f filename [-p PORT] [-P python] [--1200bps-reset]
+ECHO Usage: %SCRIPT_NAME% -f filename [-p PORT] [-P python] (--web)
 ECHO.
 ECHO Options:
 ECHO     -f filename      The firmware .bin file to flash.  Custom to your device type and region. (required)
@@ -34,16 +27,14 @@ ECHO                      If not set, ESPTOOL iterates all ports (Dangerous).
 ECHO     -P python        Specify alternate python interpreter to use to invoke esptool. (default: python)
 ECHO                      If supplied the script will use python.
 ECHO                      If not supplied the script will try to find esptool in Path.
-ECHO     --1200bps-reset  Attempt to place the device in correct mode. (1200bps Reset)
-ECHO                      Some hardware requires this twice.
+ECHO     --web            Enable WebUI. (default: false)
 ECHO.
-ECHO Example: %SCRIPT_NAME% -p COM17 --1200bps-reset
 ECHO Example: %SCRIPT_NAME% -f firmware-t-deck-tft-2.6.0.0b106d4.bin -p COM11
-ECHO Example: %SCRIPT_NAME% -f firmware-unphone-2.6.0.0b106d4.bin -p COM11
+ECHO Example: %SCRIPT_NAME% -f firmware-unphone-2.6.0.0b106d4.bin -p COM11 --web
 GOTO eof
 
 :version
-ECHO %SCRIPT_NAME% [Version 2.6.2]
+ECHO %SCRIPT_NAME% [Version 2.6.0]
 ECHO Meshtastic
 GOTO eof
 
@@ -59,13 +50,11 @@ IF /I "%~1"=="-f" SET "FILENAME=%~2" & SHIFT
 IF "%~1"=="-p" SET "ESPTOOL_PORT=%~2" & SHIFT
 IF /I "%~1"=="--port" SET "ESPTOOL_PORT=%~2" & SHIFT
 IF "%~1"=="-P" SET "PYTHON=%~2" & SHIFT
-IF /I "%~1"=="--1200bps-reset" SET "BPS_RESET=1"
+IF /I "%~1"=="--web" SET "WEB_APP=1"
 SHIFT
 GOTO getopts
 :endopts
 
-IF %BPS_RESET% EQU 1 GOTO skip-filename
-
 CALL :LOG_MESSAGE DEBUG "Checking FILENAME parameter..."
 IF "__!FILENAME!__"=="____" (
     CALL :LOG_MESSAGE DEBUG "Missing -f filename input."
@@ -99,9 +88,6 @@ IF NOT "!FILENAME:update=!"=="!FILENAME!" (
     CALL :LOG_MESSAGE DEBUG "We are NOT working with a *update* file. !FILENAME!"
 )
 
-:skip-filename
-SET "ESPTOOL_BAUD=1200"
-
 CALL :LOG_MESSAGE DEBUG "Determine the correct esptool command to use..."
 IF NOT "__%PYTHON%__"=="____" (
     SET "ESPTOOL_CMD=!PYTHON! -m esptool"
@@ -120,7 +106,7 @@ IF NOT "__%PYTHON%__"=="____" (
 
 CALL :LOG_MESSAGE DEBUG "Checking esptool command !ESPTOOL_CMD!..."
 !ESPTOOL_CMD! >nul 2>&1
-IF %ERRORLEVEL% GEQ 2 (
+IF %ERRORLEVEL% GTR 2 (
     @REM esptool exits with code 1 if help is displayed.
     CALL :LOG_MESSAGE ERROR "esptool not found: !ESPTOOL_CMD!"
     EXIT /B 1
@@ -135,52 +121,56 @@ CALL :LOG_MESSAGE DEBUG "Using esptool command: !ESPTOOL_CMD!"
 IF "__!ESPTOOL_PORT!__" == "____" (
     CALL :LOG_MESSAGE WARN "Using esptool port: UNSET."
 ) ELSE (
-    SET "ESPTOOL_CMD=!ESPTOOL_CMD! --port !ESPTOOL_PORT!"
     CALL :LOG_MESSAGE INFO "Using esptool port: !ESPTOOL_PORT!."
 )
 CALL :LOG_MESSAGE INFO "Using esptool baud: !ESPTOOL_BAUD!."
 
-IF %BPS_RESET% EQU 1 (
-    @REM Attempt to change mode via 1200bps Reset.
-    CALL :RUN_ESPTOOL !ESPTOOL_BAUD! --after no_reset read_flash_status
-    GOTO eof
-)
-
 @REM Check if FILENAME contains "-tft-" and set target partitionScheme accordingly.
 @REM https://github.com/meshtastic/web-flasher/blob/main/types/resources.ts#L3
 IF NOT "!FILENAME:-tft-=!"=="!FILENAME!" (
     CALL :LOG_MESSAGE DEBUG "We are working with a *-tft-* file. !FILENAME!"
+    IF %WEB_APP% EQU 1 (
+        CALL :LOG_MESSAGE ERROR "Cannot enable WebUI (--web) and MUI." & GOTO eof
+    )
     SET "TFT_BUILD=1"
+    GOTO tft
 ) ELSE (
     CALL :LOG_MESSAGE DEBUG "We are NOT working with a *-tft-* file. !FILENAME!"
+    GOTO no_tft
 )
 
-FOR %%a IN (%BIGDB_8MB%) DO (
+:tft
+SET "TFT8MB=picomputer-s3 unphone seeed-sensecap-indicator"
+FOR %%a IN (%TFT8MB%) DO (
     IF NOT "!FILENAME:%%a=!"=="!FILENAME!" (
-        @REM We are working with any of %BIGDB_8MB%.
-        SET "BIGDB8=1"
-        GOTO end_loop_bigdb_8mb
+        @REM We are working with any of %TFT8MB%.
+        SET "TFT8=1"
+        GOTO end_loop_tft8mb
     )
 )
-:end_loop_bigdb_8mb
+:end_loop_tft8mb
 
-FOR %%a IN (%BIGDB_16MB%) DO (
+SET "TFT16MB=t-deck"
+FOR %%a IN (%TFT16MB%) DO (
     IF NOT "!FILENAME:%%a=!"=="!FILENAME!" (
-        @REM We are working with any of %BIGDB_16MB%.
-        SET "BIGDB16=1"
-        GOTO end_loop_bigdb_16mb
+        @REM We are working with any of %TFT16MB%.
+        SET "TFT16=1"
+        GOTO end_loop_tft16mb
     )
 )
-:end_loop_bigdb_16mb
+:end_loop_tft16mb
 
-IF %BIGDB8% EQU 1 CALL :LOG_MESSAGE INFO "BigDB 8mb partition selected."
-IF %BIGDB16% EQU 1 CALL :LOG_MESSAGE INFO "BigDB 16mb partition selected."
+IF %TFT8% EQU 1 CALL :LOG_MESSAGE INFO "tft and MUI 8mb selected."
+IF %TFT16% EQU 1 CALL :LOG_MESSAGE INFO "tft and MUI 16mb selected."
+
+:no_tft
 
 @REM Extract BASENAME from %FILENAME% for later use.
 SET "BASENAME=!FILENAME:firmware-=!"
 CALL :LOG_MESSAGE DEBUG "Computed firmware basename: !BASENAME!"
 
 @REM Account for S3 and C3 board's different OTA partition.
+SET "S3=s3 v3 t-deck wireless-paper wireless-tracker station-g2 unphone"
 FOR %%a IN (%S3%) DO (
     IF NOT "!FILENAME:%%a=!"=="!FILENAME!" (
         @REM We are working with any of %S3%.
@@ -189,6 +179,7 @@ FOR %%a IN (%S3%) DO (
     )
 )
 
+SET "C3=esp32c3"
 FOR %%a IN (%C3%) DO (
     IF NOT "!FILENAME:%%a=!"=="!FILENAME!" (
         @REM We are working with any of %C3%.
@@ -203,8 +194,13 @@ SET "OTA_FILENAME=bleota.bin"
 :end_loop_c3
 CALL :LOG_MESSAGE DEBUG "Set OTA_FILENAME to: !OTA_FILENAME!"
 
-@REM Set SPIFFS filename with "littlefs-" prefix.
-SET "SPIFFS_FILENAME=littlefs-%BASENAME%"
+@REM Check if (--web) is enabled and prefix BASENAME with "littlefswebui-" else "littlefs-".
+IF %WEB_APP% EQU 1 (
+    CALL :LOG_MESSAGE INFO "WebUI selected."
+    SET "SPIFFS_FILENAME=littlefswebui-%BASENAME%"
+) ELSE (
+    SET "SPIFFS_FILENAME=littlefs-%BASENAME%"
+)
 CALL :LOG_MESSAGE DEBUG "Set SPIFFS_FILENAME to: !SPIFFS_FILENAME!"
 
 @REM Default offsets.
@@ -212,14 +208,14 @@ CALL :LOG_MESSAGE DEBUG "Set SPIFFS_FILENAME to: !SPIFFS_FILENAME!"
 SET "OTA_OFFSET=0x260000"
 SET "SPIFFS_OFFSET=0x300000"
 
-@REM Offsets for BigDB 8mb.
-IF %BIGDB8% EQU 1 (
+@REM Offsets for MUI 8mb.
+IF %TFT8% EQU 1 IF %TFT_BUILD% EQU 1 (
     SET "OTA_OFFSET=0x340000"
     SET "SPIFFS_OFFSET=0x670000"
 )
 
-@REM Offsets for BigDB 16mb.
-IF %BIGDB16% EQU 1 (
+@REM Offsets for MUI 16mb.
+IF %TFT16% EQU 1 IF %TFT_BUILD% EQU 1 (
     SET "OTA_OFFSET=0x650000"
     SET "SPIFFS_OFFSET=0xc90000"
 )
@@ -259,7 +255,6 @@ EXIT /B %ERRORLEVEL%
 IF %DEBUG% EQU 1 CALL :LOG_MESSAGE DEBUG "About to run command: !ESPTOOL_CMD! --baud %~1 %~2 %~3 %~4"
 CALL :RESET_ERROR
 !ESPTOOL_CMD! --baud %~1 %~2 %~3 %~4
-IF %BPS_RESET% EQU 1 GOTO :eof
 IF %ERRORLEVEL% NEQ 0 (
     CALL :LOG_MESSAGE ERROR "Error running command: !ESPTOOL_CMD! --baud %~1 %~2 %~3 %~4"
     EXIT /B %ERRORLEVEL%

bin/device-install.sh

@@ -1,216 +1,164 @@
 #!/bin/bash
 
 PYTHON=${PYTHON:-$(which python3 python | head -n 1)}
-BPS_RESET=false
+WEB_APP=false
+TFT8=false
+TFT16=false
 TFT_BUILD=false
-MCU=""
-
-# Variant groups
-BIGDB_8MB=(
-	"picomputer-s3"
-	"unphone"
-	"seeed-sensecap-indicator"
-	"crowpanel-esp32s3"
-	"heltec_capsule_sensor_v3"
-	"heltec-v3"
-	"heltec-vision-master-e213"
-	"heltec-vision-master-e290"
-	"heltec-vision-master-t190"
-	"heltec-wireless-paper"
-	"heltec-wireless-tracker"
-	"heltec-wsl-v3"
-	"icarus"
-	"seeed-xiao-s3"
-	"tbeam-s3-core"
-	"tracksenger"
-)
-BIGDB_16MB=(
-	"t-deck"
-	"mesh-tab"
-	"t-energy-s3"
-	"dreamcatcher"
-	"ESP32-S3-Pico"
-	"m5stack-cores3"
-	"station-g2"
-    "t-eth-elite"
-    "t-watch-s3"
-    "elecrow-adv-35-tft"
-    "elecrow-adv-24-28-tft"
-    "elecrow-adv1-43-50-70-tft"
-)
-S3_VARIANTS=(
-    "s3"
-    "-v3"
-    "t-deck"
-    "wireless-paper"
-    "wireless-tracker"
-    "station-g2"
-    "unphone"
-    "t-eth-elite"
-    "mesh-tab"
-    "dreamcatcher"
-    "ESP32-S3-Pico"
-    "seeed-sensecap-indicator"
-    "heltec_capsule_sensor_v3"
-    "vision-master"
-    "icarus"
-    "tracksenger"
-    "elecrow-adv"
-)
 
 # Determine the correct esptool command to use
 if "$PYTHON" -m esptool version >/dev/null 2>&1; then
-    ESPTOOL_CMD="$PYTHON -m esptool"
+	ESPTOOL_CMD="$PYTHON -m esptool"
 elif command -v esptool >/dev/null 2>&1; then
-    ESPTOOL_CMD="esptool"
+	ESPTOOL_CMD="esptool"
 elif command -v esptool.py >/dev/null 2>&1; then
-    ESPTOOL_CMD="esptool.py"
+	ESPTOOL_CMD="esptool.py"
 else
-    echo "Error: esptool not found"
-    exit 1
+	echo "Error: esptool not found"
+	exit 1
 fi
 
 set -e
 
 # Usage info
 show_help() {
-    cat <<EOF
-Usage: $(basename "$0") [-h] [-p ESPTOOL_PORT] [-P PYTHON] [-f FILENAME] [--1200bps-reset]
+	cat <<EOF
+Usage: $(basename $0) [-h] [-p ESPTOOL_PORT] [-P PYTHON] [-f FILENAME] [--web]
 Flash image file to device, but first erasing and writing system information.
 
     -h               Display this help and exit.
     -p ESPTOOL_PORT  Set the environment variable for ESPTOOL_PORT.  If not set, ESPTOOL iterates all ports (Dangerous).
     -P PYTHON        Specify alternate python interpreter to use to invoke esptool. (Default: "$PYTHON")
     -f FILENAME      The firmware .bin file to flash.  Custom to your device type and region.
-    --1200bps-reset  Attempt to place the device in correct mode. Some hardware requires this twice. (1200bps Reset)
+    --web            Enable WebUI. (Default: false)
 
 EOF
 }
 # Parse arguments using a single while loop
 while [ $# -gt 0 ]; do
-    case "$1" in
-    -h | --help)
-        show_help
-        exit 0
-        ;;
-    -p)
-        ESPTOOL_CMD="$ESPTOOL_CMD --port $2"
-        shift
-        ;;
-    -P)
-        PYTHON="$2"
-        shift
-        ;;
-    -f)
-        FILENAME="$2"
-        shift
-        ;;
-    --1200bps-reset)
-		    BPS_RESET=true
-		    ;;
-    --) # Stop parsing options
-        shift
-        break
-        ;;
-    *)
-        echo "Unknown argument: $1" >&2
-        exit 1
-        ;;
-    esac
-    shift # Move to the next argument
+	case "$1" in
+	-h | --help)
+		show_help
+		exit 0
+		;;
+	-p)
+		ESPTOOL_PORT="$2"
+		shift # Shift past the option argument
+		;;
+	-P)
+		PYTHON="$2"
+		shift
+		;;
+	-f)
+		FILENAME="$2"
+		shift
+		;;
+	--web)
+		WEB_APP=true
+		;;
+	--) # Stop parsing options
+		shift
+		break
+		;;
+	*)
+		echo "Unknown argument: $1" >&2
+		exit 1
+		;;
+	esac
+	shift # Move to the next argument
 done
 
-if [[ $BPS_RESET == true ]]; then
-	$ESPTOOL_CMD --baud 1200 --after no_reset read_flash_status
-	exit 0
-fi
-
-[ -z "$FILENAME" ] && [ -n "$1" ] && {
-    FILENAME="$1"
-    shift
+[ -z "$FILENAME" -a -n "$1" ] && {
+	FILENAME=$1
+	shift
 }
 
-if [[ "$FILENAME" != firmware-* ]]; then
+if [[ $FILENAME != firmware-* ]]; then
   echo "Filename must be a firmware-* file."
   exit 1
 fi
 
 # Check if FILENAME contains "-tft-" and set target partitionScheme accordingly.
-if [[ "${FILENAME//-tft-/}" != "$FILENAME" ]]; then
-    TFT_BUILD=true
+if [[ ${FILENAME//-tft-/} != "$FILENAME" ]]; then
+	TFT_BUILD=true
+	if [[ $WEB_APP == true ]] && [[ $TFT_BUILD == true ]]; then
+		echo "Cannot enable WebUI (--web) and MUI."
+		exit 1
+	fi
+
+	if [[ $FILENAME == *"picomputer-s3"* || $FILENAME == *"unphone"* || $FILENAME == *"seeed-sensecap-indicator"* ]]; then
+		TFT8=true
+	fi
+
+	if [[ $FILENAME == *"t-deck"* ]]; then
+		TFT16=true
+	fi
 fi
 
 # Extract BASENAME from %FILENAME% for later use.
 BASENAME="${FILENAME/firmware-/}"
 
 if [ -f "${FILENAME}" ] && [ -n "${FILENAME##*"update"*}" ]; then
-    # Default littlefs* offset.
-    OFFSET=0x300000
+	# Default littlefs* offset (--web).
+	OFFSET=0x300000
 
-    # Default OTA Offset
-    OTA_OFFSET=0x260000
+	# Default OTA Offset
+	OTA_OFFSET=0x260000
 
-    # littlefs* offset for BigDB 8mb and OTA OFFSET.
-    for variant in "${BIGDB_8MB[@]}"; do
-        if [ -z "${FILENAME##*"$variant"*}" ]; then
-            OFFSET=0x670000
-            OTA_OFFSET=0x340000
-        fi
-    done
+	# littlefs* offset for MUI 8mb and OTA OFFSET.
+	if [ "$TFT8" = true ] && [ "$TFT_BUILD" = true ]; then
+		OFFSET=0x670000
+		OTA_OFFSET=0x340000
+	fi
 
-    # littlefs* offset for BigDB 16mb and OTA OFFSET.
-    for variant in "${BIGDB_16MB[@]}"; do
-        if [ -z "${FILENAME##*"$variant"*}" ]; then
-            OFFSET=0xc90000
-            OTA_OFFSET=0x650000
-        fi
-    done
+	# littlefs* offset for MUI 16mb and OTA OFFSET.
+	if [ "$TFT16" = true ] && [ "$TFT_BUILD" = true ]; then
+		OFFSET=0xc90000
+		OTA_OFFSET=0x650000
+	fi
 
-    # Account for S3 board's different OTA partition
-    # FIXME: Use PlatformIO info to determine MCU type, this is unmaintainable
-    for variant in "${S3_VARIANTS[@]}"; do
-        if [ -z "${FILENAME##*"$variant"*}" ]; then
-            MCU="esp32s3"
-        fi
-    done
+	# Account for S3 board's different OTA partition
+	if [ -n "${FILENAME##*"s3"*}" ] && [ -n "${FILENAME##*"-v3"*}" ] && [ -n "${FILENAME##*"t-deck"*}" ] && [ -n "${FILENAME##*"wireless-paper"*}" ] && [ -n "${FILENAME##*"wireless-tracker"*}" ] && [ -n "${FILENAME##*"station-g2"*}" ] && [ -n "${FILENAME##*"unphone"*}" ]; then
+		if [ -n "${FILENAME##*"esp32c3"*}" ]; then
+			OTAFILE=bleota.bin
+		else
+			OTAFILE=bleota-c3.bin
+		fi
+	else
+		OTAFILE=bleota-s3.bin
+	fi
 
-    if [ "$MCU" != "esp32s3" ]; then
-        if [ -n "${FILENAME##*"esp32c3"*}" ]; then
-            OTAFILE=bleota.bin
-        else
-            OTAFILE=bleota-c3.bin
-        fi
-    else
-        OTAFILE=bleota-s3.bin
-    fi
+	# Check if WEB_APP (--web) is enabled and add "littlefswebui-" to BASENAME else "littlefs-".
+	if [ "$WEB_APP" = true ]; then
+		SPIFFSFILE=littlefswebui-${BASENAME}
+	else
+		SPIFFSFILE=littlefs-${BASENAME}
+	fi
 
-    # Set SPIFFS filename with "littlefs-" prefix.
-    SPIFFSFILE=littlefs-${BASENAME}
+	if [[ ! -f $FILENAME ]]; then
+		echo "Error: file ${FILENAME} wasn't found. Terminating."
+		exit 1
+	fi
+	if [[ ! -f $OTAFILE ]]; then
+		echo "Error: file ${OTAFILE} wasn't found. Terminating."
+		exit 1
+	fi
+	if [[ ! -f $SPIFFSFILE ]]; then
+		echo "Error: file ${SPIFFSFILE} wasn't found. Terminating."
+		exit 1
+	fi
 
-    if [[ ! -f "$FILENAME" ]]; then
-        echo "Error: file ${FILENAME} wasn't found. Terminating."
-        exit 1
-    fi
-    if [[ ! -f "$OTAFILE" ]]; then
-        echo "Error: file ${OTAFILE} wasn't found. Terminating."
-        exit 1
-    fi
-    if [[ ! -f "$SPIFFSFILE" ]]; then
-        echo "Error: file ${SPIFFSFILE} wasn't found. Terminating."
-        exit 1
-    fi
-
-    echo "Trying to flash ${FILENAME}, but first erasing and writing system information"
-    $ESPTOOL_CMD erase_flash
-    $ESPTOOL_CMD write_flash 0x00 "${FILENAME}"
-    echo "Trying to flash ${OTAFILE} at offset ${OTA_OFFSET}"
-    $ESPTOOL_CMD write_flash $OTA_OFFSET "${OTAFILE}"
-    echo "Trying to flash ${SPIFFSFILE}, at offset ${OFFSET}"
-    $ESPTOOL_CMD write_flash $OFFSET "${SPIFFSFILE}"
+	echo "Trying to flash ${FILENAME}, but first erasing and writing system information"
+	$ESPTOOL_CMD erase_flash
+	$ESPTOOL_CMD write_flash 0x00 "${FILENAME}"
+	echo "Trying to flash ${OTAFILE} at offset ${OTA_OFFSET}"
+	$ESPTOOL_CMD write_flash $OTA_OFFSET "${OTAFILE}"
+	echo "Trying to flash ${SPIFFSFILE}, at offset ${OFFSET}"
+	$ESPTOOL_CMD write_flash $OFFSET "${SPIFFSFILE}"
 
 else
-    show_help
-    echo "Invalid file: ${FILENAME}"
+	show_help
+	echo "Invalid file: ${FILENAME}"
 fi
 
 exit 0

bin/device-update.bat

@@ -8,31 +8,27 @@ SET "PYTHON="
 SET "ESPTOOL_BAUD=115200"
 SET "ESPTOOL_CMD="
 SET "LOGCOUNTER=0"
-SET "CHANGE_MODE=0"
 
 GOTO getopts
 :help
 ECHO Flash image file to device, but leave existing system intact.
 ECHO.
-ECHO Usage: %SCRIPT_NAME% -f filename [-p PORT] [-P python] [--change-mode]
+ECHO Usage: %SCRIPT_NAME% -f filename [-p PORT] [-P python]
 ECHO.
 ECHO Options:
-ECHO     -f filename      The update .bin file to flash.  Custom to your device type and region. (required)
+ECHO     -f filename      The .bin file to flash.  Custom to your device type and region. (required)
 ECHO                      The file must be located in this current directory.
 ECHO     -p PORT          Set the environment variable for ESPTOOL_PORT.
 ECHO                      If not set, ESPTOOL iterates all ports (Dangerous).
 ECHO     -P python        Specify alternate python interpreter to use to invoke esptool. (default: python)
 ECHO                      If supplied the script will use python.
 ECHO                      If not supplied the script will try to find esptool in Path.
-ECHO     --change-mode    Attempt to place the device in correct mode. (1200bps Reset)
-ECHO                      Some hardware requires this twice.
 ECHO.
-ECHO Example: %SCRIPT_NAME% -p COM17 --change-mode
 ECHO Example: %SCRIPT_NAME% -f firmware-t-deck-tft-2.6.0.0b106d4-update.bin -p COM11
 GOTO eof
 
 :version
-ECHO %SCRIPT_NAME% [Version 2.6.2]
+ECHO %SCRIPT_NAME% [Version 2.6.0]
 ECHO Meshtastic
 GOTO eof
 
@@ -48,19 +44,15 @@ IF /I "%~1"=="-f" SET "FILENAME=%~2" & SHIFT
 IF "%~1"=="-p" SET "ESPTOOL_PORT=%~2" & SHIFT
 IF /I "%~1"=="--port" SET "ESPTOOL_PORT=%~2" & SHIFT
 IF "%~1"=="-P" SET "PYTHON=%~2" & SHIFT
-IF /I "%~1"=="--change-mode" SET "CHANGE_MODE=1"
 SHIFT
 GOTO getopts
 :endopts
 
-IF %CHANGE_MODE% EQU 1 GOTO skip-filename
-
 CALL :LOG_MESSAGE DEBUG "Checking FILENAME parameter..."
 IF "__!FILENAME!__"=="____" (
     CALL :LOG_MESSAGE DEBUG "Missing -f filename input."
     GOTO help
 ) ELSE (
-    CALL :LOG_MESSAGE DEBUG "Filename: !FILENAME!"
     IF NOT "__!FILENAME: =!__"=="__!FILENAME!__" (
         CALL :LOG_MESSAGE ERROR "Filename containing spaces are not supported."
         GOTO help
@@ -70,6 +62,7 @@ IF "__!FILENAME!__"=="____" (
     SET "FILENAME=!FILENAME:./=!"
 )
 
+CALL :LOG_MESSAGE DEBUG "Filename: !FILENAME!"
 CALL :LOG_MESSAGE DEBUG "Checking if !FILENAME! exists..."
 IF NOT EXIST !FILENAME! (
     CALL :LOG_MESSAGE ERROR "File does not exist: !FILENAME!. Terminating."
@@ -78,15 +71,12 @@ IF NOT EXIST !FILENAME! (
 
 IF "!FILENAME:update=!"=="!FILENAME!" (
     CALL :LOG_MESSAGE DEBUG "We are NOT working with a *update* file. !FILENAME!"
-    CALL :LOG_MESSAGE INFO "Use script device-install.bat to flash !FILENAME!."
+    CALL :LOG_MESSAGE INFO "Use script device-install.bat to flash update !FILENAME!."
     GOTO eof
 ) ELSE (
     CALL :LOG_MESSAGE DEBUG "We are working with a *update* file. !FILENAME!"
 )
 
-:skip-filename
-SET "ESPTOOL_BAUD=1200"
-
 CALL :LOG_MESSAGE DEBUG "Determine the correct esptool command to use..."
 IF NOT "__%PYTHON%__"=="____" (
     SET "ESPTOOL_CMD=!PYTHON! -m esptool"
@@ -105,7 +95,7 @@ IF NOT "__%PYTHON%__"=="____" (
 
 CALL :LOG_MESSAGE DEBUG "Checking esptool command !ESPTOOL_CMD!..."
 !ESPTOOL_CMD! >nul 2>&1
-IF %ERRORLEVEL% GEQ 2 (
+IF %ERRORLEVEL% GTR 2 (
     @REM esptool exits with code 1 if help is displayed.
     CALL :LOG_MESSAGE ERROR "esptool not found: !ESPTOOL_CMD!"
     EXIT /B 1
@@ -120,17 +110,10 @@ CALL :LOG_MESSAGE DEBUG "Using esptool command: !ESPTOOL_CMD!"
 IF "__!ESPTOOL_PORT!__" == "____" (
     CALL :LOG_MESSAGE WARN "Using esptool port: UNSET."
 ) ELSE (
-    SET "ESPTOOL_CMD=!ESPTOOL_CMD! --port !ESPTOOL_PORT!"
     CALL :LOG_MESSAGE INFO "Using esptool port: !ESPTOOL_PORT!."
 )
 CALL :LOG_MESSAGE INFO "Using esptool baud: !ESPTOOL_BAUD!."
 
-IF %CHANGE_MODE% EQU 1 (
-    @REM Attempt to change mode via 1200bps Reset.
-    CALL :RUN_ESPTOOL !ESPTOOL_BAUD! --after no_reset read_flash_status
-    GOTO eof
-)
-
 @REM Flashing operations.
 CALL :LOG_MESSAGE INFO "Trying to flash update "!FILENAME!" at OFFSET 0x10000..."
 CALL :RUN_ESPTOOL !ESPTOOL_BAUD! write_flash 0x10000 "!FILENAME!" || GOTO eof
@@ -151,7 +134,6 @@ EXIT /B %ERRORLEVEL%
 IF %DEBUG% EQU 1 CALL :LOG_MESSAGE DEBUG "About to run command: !ESPTOOL_CMD! --baud %~1 %~2 %~3 %~4"
 CALL :RESET_ERROR
 !ESPTOOL_CMD! --baud %~1 %~2 %~3 %~4
-IF %CHANGE_MODE% EQU 1 GOTO :eof
 IF %ERRORLEVEL% NEQ 0 (
     CALL :LOG_MESSAGE ERROR "Error running command: !ESPTOOL_CMD! --baud %~1 %~2 %~3 %~4"
     EXIT /B %ERRORLEVEL%

bin/device-update.sh

@@ -1,7 +1,6 @@
 #!/bin/sh
 
 PYTHON=${PYTHON:-$(which python3 python|head -n 1)}
-CHANGE_MODE=false
 
 # Determine the correct esptool command to use
 if "$PYTHON" -m esptool version >/dev/null 2>&1; then
@@ -18,29 +17,17 @@ fi
 # Usage info
 show_help() {
 cat << EOF
-Usage: $(basename "$0") [-h] [-p ESPTOOL_PORT] [-P PYTHON] [-f FILENAME|FILENAME] [--change-mode]
+Usage: $(basename $0) [-h] [-p ESPTOOL_PORT] [-P PYTHON] [-f FILENAME|FILENAME]
 Flash image file to device, leave existing system intact."
 
     -h               Display this help and exit
     -p ESPTOOL_PORT  Set the environment variable for ESPTOOL_PORT.  If not set, ESPTOOL iterates all ports (Dangerous).
     -P PYTHON        Specify alternate python interpreter to use to invoke esptool. (Default: "$PYTHON")
     -f FILENAME      The *update.bin file to flash.  Custom to your device type.
-    --change-mode    Attempt to place the device in correct mode. Some hardware requires this twice. (1200bps Reset)
-
+    
 EOF
 }
 
-# Check for --change-mode and remove it from arguments
-NEW_ARGS=()
-for arg in "$@"; do
-    if [ "$arg" = "--change-mode" ]; then
-        CHANGE_MODE=true
-    else
-        NEW_ARGS+=("$arg")
-    fi
-done
-
-set -- "${NEW_ARGS[@]}"
 
 while getopts ":hp:P:f:" opt; do
     case "${opt}" in
@@ -48,14 +35,14 @@ while getopts ":hp:P:f:" opt; do
             show_help
             exit 0
             ;;
-        p)  ESPTOOL_CMD="$ESPTOOL_CMD --port ${OPTARG}"
-            ;;
+        p)  export ESPTOOL_PORT=${OPTARG}
+	    ;;
         P)  PYTHON=${OPTARG}
             ;;
         f)  FILENAME=${OPTARG}
             ;;
         *)
-            echo "Invalid flag."
+ 	        echo "Invalid flag."
             show_help >&2
             exit 1
             ;;
@@ -63,22 +50,17 @@ while getopts ":hp:P:f:" opt; do
 done
 shift "$((OPTIND-1))"
 
-if [ "$CHANGE_MODE" = true ]; then
-	$ESPTOOL_CMD --baud 1200 --after no_reset read_flash_status
-    exit 0
-fi
-
-[ -z "$FILENAME" ]  && [ -n "$1" ] && {
-    FILENAME="$1"
+[ -z "$FILENAME" -a -n "$1" ] && {
+    FILENAME=$1
     shift
 }
 
 if [ -f "${FILENAME}" ] && [ -z "${FILENAME##*"update"*}" ]; then
-    echo "Trying to flash update ${FILENAME}"
-    $ESPTOOL_CMD --baud 115200 write_flash 0x10000 "${FILENAME}"
+	printf "Trying to flash update ${FILENAME}"
+	$ESPTOOL_CMD --baud 115200 write_flash 0x10000 ${FILENAME}
 else
-    show_help
-    echo "Invalid file: ${FILENAME}"
+	show_help
+	echo "Invalid file: ${FILENAME}"
 fi
 
 exit 0

bin/generate_ci_matrix.py

@@ -27,7 +27,7 @@ for subdir, dirs, files in os.walk(rootdir):
                 if c.startswith("env:"):
                     section = config[c].name[4:]
                     if "extends" in config[config[c].name]:
-                        if options[0] + "_base" in config[config[c].name]["extends"]:
+                        if config[config[c].name]["extends"] == options[0] + "_base":
                             if "board_level" in config[config[c].name]:
                                 if (
                                     config[config[c].name]["board_level"] == "extra"

bin/meshtasticd.service

@@ -5,11 +5,10 @@ StartLimitInterval=200
 StartLimitBurst=5
 
 [Service]
-AmbientCapabilities=CAP_NET_BIND_SERVICE
-User=meshtasticd
-Group=meshtasticd
+User=root
+Group=root
 Type=simple
-ExecStart=/usr/bin/meshtasticd
+ExecStart=/usr/sbin/meshtasticd
 Restart=always
 RestartSec=3
 

bin/native-install.sh

@@ -1,6 +1,6 @@
 #!/usr/bin/env bash
 
-cp "release/meshtasticd_linux_$(uname -m)" /usr/bin/meshtasticd
+cp "release/meshtasticd_linux_$(uname -m)" /usr/sbin/meshtasticd
 mkdir -p /etc/meshtasticd
 if [[ -f "/etc/meshtasticd/config.yaml" ]]; then
 	cp bin/config-dist.yaml /etc/meshtasticd/config-upgrade.yaml

bin/org.meshtastic.meshtasticd.desktop

@@ -1,8 +0,0 @@
-[Desktop Entry]
-Name=Meshtastic
-Comment=Meshtastic App
-Exec=meshtasticd
-Icon=org.meshtastic.meshtasticd
-Terminal=true
-Type=Application
-Categories=Network;Chat;HamRadio;

bin/org.meshtastic.meshtasticd.metainfo.xml

@@ -1,133 +0,0 @@
-<?xml version='1.0' encoding='UTF-8'?>
-<component type="desktop-application">
-  <id>org.meshtastic.meshtasticd</id>
-
-  <name>Meshtastic</name>
-  <summary>Decentralized mesh communication</summary>
-
-  <metadata_license>CC-BY-4.0</metadata_license>
-  <project_license>GPL-3.0-or-later</project_license>
-
-  <developer id="org.meshtastic">
-    <name>Meshtastic</name>
-  </developer>
-
-  <description>
-    <p>
-      Meshtastic is an open source project for creating off-grid, affordable, and resilient communication with LoRa mesh networks.
-    </p>
-  </description>
-
-  <launchable type="desktop-id">org.meshtastic.meshtasticd.desktop</launchable>
-
-  <categories>
-    <category>Network</category>
-    <category>Chat</category>
-    <category>HamRadio</category>
-  </categories>
-  <keywords>
-    <keyword>mesh</keyword>
-    <keyword>LoRa</keyword>
-  </keywords>
-
-  <recommends>
-    <control>keyboard</control>
-    <control>pointing</control>
-    <control>touch</control>
-  </recommends>
-  <requires>
-    <display_length compare="ge">360</display_length>
-  </requires>
-
-  <branding>
-    <color type="primary" scheme_preference="light">#97be89</color>
-    <color type="primary" scheme_preference="dark">#206538</color>
-  </branding>
-
-  <content_rating type="oars-1.1">
-    <content_attribute id="social-chat">intense</content_attribute>
-    <content_attribute id="social-location">intense</content_attribute>
-  </content_rating>
-
-  <url type="bugtracker">https://github.com/meshtastic/firmware/issues</url>
-  <url type="homepage">https://meshtastic.org/</url>
-  <url type="donation">https://opencollective.com/meshtastic</url>
-  <url type="faq">https://meshtastic.org/docs/software/linux/usage/</url>
-  <url type="vcs-browser">https://github.com/meshtastic/firmware/</url>
-
-  <screenshots>
-    <screenshot type="default">
-      <image>https://meshtastic.org/img/software/meshtastic-ui/mui_home_dashboard_dark.webp</image>
-      <caption>Home Dashboard</caption>
-    </screenshot>
-    <screenshot>
-      <image>https://meshtastic.org/img/software/meshtastic-ui/mui_initial_boot.webp</image>
-      <caption>Setup</caption>
-    </screenshot>
-    <screenshot>
-      <image>https://meshtastic.org/img/software/meshtastic-ui/mui_node_list_dark.webp</image>
-      <caption>Nodes List</caption>
-    </screenshot>
-    <screenshot>
-      <image>https://meshtastic.org/img/software/meshtastic-ui/mui_chat_list_dark.webp</image>
-      <caption>Chats List</caption>
-    </screenshot>
-    <screenshot>
-      <image>https://meshtastic.org/img/software/meshtastic-ui/mui_chat_message_dark.webp</image>
-      <caption>Messages</caption>
-    </screenshot>
-    <screenshot>
-      <image>https://meshtastic.org/img/software/meshtastic-ui/mui_map_dark.webp</image>
-      <caption>Map</caption>
-    </screenshot>
-    <screenshot>
-      <image>https://meshtastic.org/img/software/meshtastic-ui/mui_settings_dark.webp</image>
-      <caption>Settings</caption>
-    </screenshot>
-  </screenshots>
-
-  <releases>
-    <release version="2.7.3" date="2025-07-10">
-      <url type="details">https://github.com/meshtastic/firmware/releases?q=tag%3Av2.7.3</url>
-    </release>
-    <release version="2.7.2" date="2025-07-04">
-      <url type="details">https://github.com/meshtastic/firmware/releases?q=tag%3Av2.7.2</url>
-    </release>
-    <release version="2.7.1" date="2025-06-27">
-      <url type="details">https://github.com/meshtastic/firmware/releases?q=tag%3Av2.7.1</url>
-    </release>
-    <release version="2.7.0" date="2025-06-20">
-      <url type="details">https://github.com/meshtastic/firmware/releases?q=tag%3Av2.7.0</url>
-    </release>
-    <release version="2.6.13" date="2025-06-16">
-      <url type="details">https://github.com/meshtastic/firmware/releases?q=tag%3Av2.6.13</url>
-    </release>
-    <release version="2.6.12" date="2025-06-15">
-      <url type="details">https://github.com/meshtastic/firmware/releases?q=tag%3Av2.6.12</url>
-    </release>
-    <release version="2.6.11" date="2025-06-02">
-      <url type="details">https://github.com/meshtastic/firmware/releases?q=tag%3Av2.6.11</url>
-    </release>
-    <release version="2.6.10" date="2025-05-25">
-      <url type="details">https://github.com/meshtastic/firmware/releases?q=tag%3Av2.6.10</url>
-    </release>
-    <release version="2.6.9" date="2025-05-15">
-      <url type="details">https://github.com/meshtastic/firmware/releases?q=tag%3Av2.6.9</url>
-    </release>
-    <release version="2.6.8" date="2025-05-05">
-      <url type="details">https://github.com/meshtastic/firmware/releases?q=tag%3Av2.6.8</url>
-    </release>
-    <release version="2.6.7" date="2025-04-28">
-      <url type="details">https://github.com/meshtastic/firmware/releases?q=tag%3Av2.6.7</url>
-    </release>
-    <release version="2.6.6" date="2025-04-15">
-      <url type="details">https://github.com/meshtastic/firmware/releases?q=tag%3Av2.6.6</url>
-    </release>
-    <release version="2.6.5" date="2025-03-30">
-      <url type="details">https://github.com/meshtastic/firmware/releases?q=tag%3Av2.6.5</url>
-    </release>
-    <release version="2.6.4" date="2025-03-28">
-      <url type="details">https://github.com/meshtastic/firmware/releases?q=tag%3Av2.6.4</url>
-    </release>
-  </releases>
-</component>

bin/org.meshtastic.meshtasticd.svg

@@ -1,16 +0,0 @@
-<?xml version="1.0" encoding="UTF-8" standalone="no" ?>
-<!DOCTYPE svg PUBLIC "-//W3C//DTD SVG 1.1//EN" "http://www.w3.org/Graphics/SVG/1.1/DTD/svg11.dtd">
-<svg xmlns="http://www.w3.org/2000/svg" xmlns:xlink="http://www.w3.org/1999/xlink" version="1.1" width="512" height="512" viewBox="0 0 512 512" xml:space="preserve">
-<desc>Created with Fabric.js 4.6.0</desc>
-<defs>
-</defs>
-<g transform="matrix(1 0 0 1 256 256)" id="xYQ9Gk9Jwpgj_HMOXB3F_"  >
-<path style="stroke: rgb(213,130,139); stroke-width: 0; stroke-dasharray: none; stroke-linecap: butt; stroke-dashoffset: 0; stroke-linejoin: miter; stroke-miterlimit: 4; fill: rgb(103,234,148); fill-rule: nonzero; opacity: 1;" vector-effect="non-scaling-stroke"  transform=" translate(-256, -256)" d="M 0 0 L 512 0 L 512 512 L 0 512 z" stroke-linecap="round" />
-</g>
-<g transform="matrix(1.79 0 0 1.79 313.74 258.36)" id="1xBsk2n9FZp60Rz1O-ceJ"  >
-<path style="stroke: none; stroke-width: 1; stroke-dasharray: none; stroke-linecap: butt; stroke-dashoffset: 0; stroke-linejoin: round; stroke-miterlimit: 2; fill: rgb(44,45,60); fill-rule: evenodd; opacity: 1;" vector-effect="non-scaling-stroke"  transform=" translate(-250.97, -362.41)" d="M 250.908 330.267 L 193.126 415.005 L 180.938 406.694 L 244.802 313.037 C 246.174 311.024 248.453 309.819 250.889 309.816 C 253.326 309.814 255.606 311.015 256.982 313.026 L 320.994 406.536 L 308.821 414.869 L 250.908 330.267 Z" stroke-linecap="round" />
-</g>
-<g transform="matrix(1.81 0 0 1.81 145 256.15)" id="KxN7E9YpbyPgz0S4z4Cl6"  >
-<path style="stroke: none; stroke-width: 1; stroke-dasharray: none; stroke-linecap: butt; stroke-dashoffset: 0; stroke-linejoin: round; stroke-miterlimit: 2; fill: rgb(44,45,60); fill-rule: evenodd; opacity: 1;" vector-effect="non-scaling-stroke"  transform=" translate(-115.14, -528.06)" d="M 87.642 581.398 L 154.757 482.977 L 142.638 474.713 L 75.523 573.134 L 87.642 581.398 Z" stroke-linecap="round" />
-</g>
-</svg>

bin/platformio-custom.py

@@ -83,7 +83,7 @@ if platform.name == "espressif32":
 
 if platform.name == "nordicnrf52":
     env.AddPostAction("$BUILD_DIR/${PROGNAME}.hex",
-                      env.VerboseAction(f"\"{sys.executable}\" ./bin/uf2conv.py $BUILD_DIR/firmware.hex -c -f 0xADA52840 -o $BUILD_DIR/firmware.uf2",
+                      env.VerboseAction(f"{sys.executable} ./bin/uf2conv.py $BUILD_DIR/firmware.hex -c -f 0xADA52840 -o $BUILD_DIR/firmware.uf2",
                                         "Generating UF2 file"))
 
 Import("projenv")
@@ -131,33 +131,3 @@ for lb in env.GetLibBuilders():
     if lb.name == "meshtastic-device-ui":
         lb.env.Append(CPPDEFINES=[("APP_VERSION", verObj["long"])])
         break
-
-# Get the display resolution from macros
-def get_display_resolution(build_flags):
-    # Check "DISPLAY_SIZE" to determine the screen resolution
-    for flag in build_flags:
-        if isinstance(flag, tuple) and flag[0] == "DISPLAY_SIZE":
-            screen_width, screen_height = map(int, flag[1].split("x"))
-            return screen_width, screen_height
-    print("No screen resolution defined in build_flags. Please define DISPLAY_SIZE.")
-    exit(1)
-
-def load_boot_logo(source, target, env):
-    build_flags = env.get("CPPDEFINES", [])
-    logo_w, logo_h = get_display_resolution(build_flags)
-    print(f"TFT build with {logo_w}x{logo_h} resolution detected")
-
-    # Load the boot logo from `branding/logo_<width>x<height>.png` if it exists
-    source_path = join(env["PROJECT_DIR"], "branding", f"logo_{logo_w}x{logo_h}.png")
-    dest_dir = join(env["PROJECT_DIR"], "data", "boot")
-    dest_path = join(dest_dir, "logo.png")
-    if env.File(source_path).exists():
-        print(f"Loading boot logo from {source_path}")
-        # Prepare the destination
-        env.Execute(f"mkdir -p {dest_dir} && rm -f {dest_path}")
-        # Copy the logo to the `data/boot` directory
-        env.Execute(f"cp {source_path} {dest_path}")
-
-# Load the boot logo on TFT builds
-if ("HAS_TFT", 1) in env.get("CPPDEFINES", []):
-    env.AddPreAction('$BUILD_DIR/littlefs.bin', load_boot_logo)

bin/rpkg.macros

@@ -2,10 +2,6 @@ function meshtastic_version {
     meshtastic_version=$(python3 bin/buildinfo.py short)
     echo -n "$meshtastic_version"
 }
-function web_version {
-    web_version=$(cat bin/web.version)
-    echo -n "$web_version"
-}
 function git_commits_num {
     total_commits=$(git rev-list --all --count)
     echo -n "$total_commits"

bin/web.version

@@ -1 +0,0 @@
-2.6.4

boards/ThinkNode-M1.json

@@ -1,53 +0,0 @@
-{
-  "build": {
-    "arduino": {
-      "ldscript": "nrf52840_s140_v6.ld"
-    },
-    "core": "nRF5",
-    "cpu": "cortex-m4",
-    "extra_flags": "-DARDUINO_NRF52840_TTGO_EINK -DNRF52840_XXAA",
-    "f_cpu": "64000000L",
-    "hwids": [
-      ["0x239A", "0x4405"],
-      ["0x239A", "0x0029"],
-      ["0x239A", "0x002A"]
-    ],
-    "usb_product": "elecrow_eink",
-    "mcu": "nrf52840",
-    "variant": "ELECROW-ThinkNode-M1",
-    "variants_dir": "variants",
-    "bsp": {
-      "name": "adafruit"
-    },
-    "softdevice": {
-      "sd_flags": "-DS140",
-      "sd_name": "s140",
-      "sd_version": "6.1.1",
-      "sd_fwid": "0x00B6"
-    },
-    "bootloader": {
-      "settings_addr": "0xFF000"
-    }
-  },
-  "connectivity": ["bluetooth"],
-  "debug": {
-    "jlink_device": "nRF52840_xxAA",
-    "onboard_tools": ["jlink"],
-    "svd_path": "nrf52840.svd",
-    "openocd_target": "nrf52840-mdk-rs"
-  },
-  "frameworks": ["arduino"],
-  "name": "elecrow eink",
-  "upload": {
-    "maximum_ram_size": 248832,
-    "maximum_size": 815104,
-    "speed": 115200,
-    "protocol": "nrfutil",
-    "protocols": ["jlink", "nrfjprog", "nrfutil", "stlink"],
-    "use_1200bps_touch": true,
-    "require_upload_port": true,
-    "wait_for_upload_port": true
-  },
-  "url": "https://www.elecrow.com/thinknode-m1-meshtastic-lora-signal-transceiver-powered-by-nrf52840-with-154-screen-support-gps.html",
-  "vendor": "ELECROW"
-}

boards/crowpanel.json

@@ -1,43 +0,0 @@
-{
-  "build": {
-    "arduino": {
-      "ldscript": "esp32s3_out.ld",
-      "memory_type": "qio_opi",
-      "partitions": "default_16MB.csv"
-    },
-    "core": "esp32",
-    "extra_flags": [
-      "-DBOARD_HAS_PSRAM",
-      "-DARDUINO_USB_CDC_ON_BOOT=0",
-      "-DARDUINO_USB_MODE=1",
-      "-DARDUINO_RUNNING_CORE=1",
-      "-DARDUINO_EVENT_RUNNING_CORE=0"
-    ],
-    "f_cpu": "240000000L",
-    "f_flash": "80000000L",
-    "flash_mode": "qio",
-    "hwids": [["0x303A", "0x1001"]],
-    "mcu": "esp32s3",
-    "variant": "ESP32-S3-WROOM-1-N16R8"
-  },
-  "connectivity": ["wifi", "bluetooth", "lora"],
-  "debug": {
-    "default_tool": "esp-builtin",
-    "onboard_tools": ["esp-builtin"],
-    "openocd_target": "esp32s3.cfg"
-  },
-  "frameworks": ["arduino", "espidf"],
-  "name": "ESP32-S3-WROOM-1-N16R8 (16 MB Flash, 8 MB PSRAM)",
-  "upload": {
-    "flash_size": "16MB",
-    "maximum_ram_size": 524288,
-    "maximum_size": 16777216,
-    "require_upload_port": true,
-    "speed": 921600
-  },
-  "monitor": {
-    "speed": 115200
-  },
-  "url": "https://www.espressif.com/sites/default/files/documentation/esp32-s3-wroom-1_wroom-1u_datasheet_en.pdf",
-  "vendor": "Espressif"
-}

boards/gat562_mesh_trial_tracker.json

@@ -1,52 +0,0 @@
-{
-  "build": {
-    "arduino": {
-      "ldscript": "nrf52840_s140_v6.ld"
-    },
-    "core": "nRF5",
-    "cpu": "cortex-m4",
-    "extra_flags": "-DARDUINO_NRF52840_FEATHER -DNRF52840_XXAA",
-    "f_cpu": "64000000L",
-    "hwids": [
-      ["0x239A", "0x8029"],
-      ["0x239A", "0x0029"],
-      ["0x239A", "0x002A"],
-      ["0x239A", "0x802A"]
-    ],
-    "usb_product": "GAT562 Mesh Trial Tracker",
-    "mcu": "nrf52840",
-    "variant": "gat562_mesh_trial_tracker",
-    "bsp": {
-      "name": "adafruit"
-    },
-    "softdevice": {
-      "sd_flags": "-DS140",
-      "sd_name": "s140",
-      "sd_version": "6.1.1",
-      "sd_fwid": "0x00B6"
-    },
-    "bootloader": {
-      "settings_addr": "0xFF000"
-    }
-  },
-  "connectivity": ["bluetooth"],
-  "debug": {
-    "jlink_device": "nRF52840_xxAA",
-    "svd_path": "nrf52840.svd",
-    "openocd_target": "nrf52840-mdk-rs"
-  },
-  "frameworks": ["arduino", "freertos"],
-  "name": "GAT562 Mesh Trial Tracker",
-  "upload": {
-    "maximum_ram_size": 248832,
-    "maximum_size": 815104,
-    "speed": 115200,
-    "protocol": "nrfutil",
-    "protocols": ["jlink", "nrfjprog", "nrfutil", "stlink"],
-    "use_1200bps_touch": true,
-    "require_upload_port": true,
-    "wait_for_upload_port": true
-  },
-  "url": "http://www.gat-iot.com/",
-  "vendor": "GAT-IOT"
-}

boards/heltec_mesh_node_t114.json

@@ -10,8 +10,7 @@
     "hwids": [
       ["0x239A", "0x4405"],
       ["0x239A", "0x0029"],
-      ["0x239A", "0x002A"],
-      ["0x2886", "0x1667"]
+      ["0x239A", "0x002A"]
     ],
     "usb_product": "HT-n5262",
     "mcu": "nrf52840",
@@ -49,6 +48,6 @@
     "require_upload_port": true,
     "wait_for_upload_port": true
   },
-  "url": "https://heltec.org/project/mesh-node-t114/",
+  "url": "FIXME",
   "vendor": "Heltec"
 }

boards/heltec_mesh_pocket.json

@@ -1,53 +0,0 @@
-{
-  "build": {
-    "arduino": {
-      "ldscript": "nrf52840_s140_v6.ld"
-    },
-    "core": "nRF5",
-    "cpu": "cortex-m4",
-    "extra_flags": "-DNRF52840_XXAA",
-    "f_cpu": "64000000L",
-    "hwids": [
-      ["0x239A", "0x4405"],
-      ["0x239A", "0x0029"],
-      ["0x239A", "0x002A"]
-    ],
-    "usb_product": "HT-n5262",
-    "mcu": "nrf52840",
-    "variant": "heltec_mesh_pocket",
-    "variants_dir": "variants",
-    "bsp": {
-      "name": "adafruit"
-    },
-    "softdevice": {
-      "sd_flags": "-DS140",
-      "sd_name": "s140",
-      "sd_version": "6.1.1",
-      "sd_fwid": "0x00B6"
-    },
-    "bootloader": {
-      "settings_addr": "0xFF000"
-    }
-  },
-  "connectivity": ["bluetooth"],
-  "debug": {
-    "jlink_device": "nRF52840_xxAA",
-    "onboard_tools": ["jlink"],
-    "svd_path": "nrf52840.svd",
-    "openocd_target": "nrf52840-mdk-rs"
-  },
-  "frameworks": ["arduino"],
-  "name": "Heltec nrf (Adafruit BSP)",
-  "upload": {
-    "maximum_ram_size": 248832,
-    "maximum_size": 815104,
-    "speed": 115200,
-    "protocol": "nrfutil",
-    "protocols": ["jlink", "nrfjprog", "nrfutil", "stlink"],
-    "use_1200bps_touch": true,
-    "require_upload_port": true,
-    "wait_for_upload_port": true
-  },
-  "url": "https://heltec.org/project/meshpocket/",
-  "vendor": "Heltec"
-}

boards/heltec_vision_master_e213.json

@@ -2,8 +2,7 @@
   "build": {
     "arduino": {
       "ldscript": "esp32s3_out.ld",
-      "partitions": "default_8MB.csv",
-      "memory_type": "qio_opi"
+      "partitions": "default_8MB.csv"
     },
     "core": "esp32",
     "extra_flags": [
@@ -16,7 +15,6 @@
     "f_cpu": "240000000L",
     "f_flash": "80000000L",
     "flash_mode": "qio",
-    "psram_type": "opi",
     "hwids": [
       ["0x303A", "0x1001"],
       ["0x303A", "0x0002"]

boards/heltec_vision_master_e290.json

@@ -2,8 +2,7 @@
   "build": {
     "arduino": {
       "ldscript": "esp32s3_out.ld",
-      "partitions": "default_8MB.csv",
-      "memory_type": "qio_opi"
+      "partitions": "default_8MB.csv"
     },
     "core": "esp32",
     "extra_flags": [
@@ -16,7 +15,6 @@
     "f_cpu": "240000000L",
     "f_flash": "80000000L",
     "flash_mode": "qio",
-    "psram_type": "opi",
     "hwids": [
       ["0x303A", "0x1001"],
       ["0x303A", "0x0002"]

boards/heltec_vision_master_t190.json

@@ -2,8 +2,7 @@
   "build": {
     "arduino": {
       "ldscript": "esp32s3_out.ld",
-      "partitions": "default_8MB.csv",
-      "memory_type": "qio_opi"
+      "partitions": "default_8MB.csv"
     },
     "core": "esp32",
     "extra_flags": [
@@ -16,7 +15,6 @@
     "f_cpu": "240000000L",
     "f_flash": "80000000L",
     "flash_mode": "qio",
-    "psram_type": "opi",
     "hwids": [
       ["0x303A", "0x1001"],
       ["0x303A", "0x0002"]

boards/seeed-sensecap-indicator.json

@@ -18,7 +18,6 @@
     "f_boot": "120000000L",
     "boot": "qio",
     "flash_mode": "qio",
-    "psram_type": "opi",
     "hwids": [["0x1A86", "0x7523"]],
     "mcu": "esp32s3",
     "variant": "esp32s3"

boards/seeed-xiao-s3.json

@@ -15,7 +15,6 @@
     "f_cpu": "240000000L",
     "f_flash": "80000000L",
     "flash_mode": "qio",
-    "psram_type": "opi",
     "hwids": [["0x2886", "0x0059"]],
     "mcu": "esp32s3",
     "variant": "seeed-xiao-s3"

boards/seeed_solar_node.json

@@ -1,54 +0,0 @@
-{
-  "build": {
-    "arduino": {
-      "ldscript": "nrf52840_s140_v7.ld"
-    },
-    "core": "nRF5",
-    "cpu": "cortex-m4",
-    "extra_flags": "-DARDUINO_MDBT50Q_RX -DNRF52840_XXAA",
-    "f_cpu": "64000000L",
-    "hwids": [["0x2886", "0x0059"]],
-    "usb_product": "XIAO-BOOT",
-    "mcu": "nrf52840",
-    "variant": "seeed_solar_node",
-    "bsp": {
-      "name": "adafruit"
-    },
-    "softdevice": {
-      "sd_flags": "-DS140",
-      "sd_name": "s140",
-      "sd_version": "7.3.0",
-      "sd_fwid": "0x0123"
-    },
-    "bootloader": {
-      "settings_addr": "0xFF000"
-    }
-  },
-  "connectivity": ["bluetooth"],
-  "debug": {
-    "jlink_device": "nRF52840_xxAA",
-    "svd_path": "nrf52840.svd",
-    "openocd_target": "nrf52840-mdk-rs"
-  },
-  "frameworks": ["arduino"],
-  "name": "seeed_solar_node",
-  "upload": {
-    "maximum_ram_size": 248832,
-    "maximum_size": 815104,
-    "speed": 115200,
-    "protocol": "nrfutil",
-    "protocols": [
-      "jlink",
-      "nrfjprog",
-      "nrfutil",
-      "stlink",
-      "cmsis-dap",
-      "blackmagic"
-    ],
-    "use_1200bps_touch": true,
-    "require_upload_port": true,
-    "wait_for_upload_port": true
-  },
-  "url": "https://www.seeedstudio.com/Seeed-XIAO-BLE-Sense-nRF52840-p-5253.html",
-  "vendor": "Seeed Studio"
-}

boards/seeed_wio_tracker_L1.json

@@ -1,57 +0,0 @@
-{
-  "build": {
-    "arduino": {
-      "ldscript": "nrf52840_s140_v7.ld"
-    },
-    "core": "nRF5",
-    "cpu": "cortex-m4",
-    "extra_flags": "-DARDUINO_MDBT50Q_RX -DNRF52840_XXAA",
-    "f_cpu": "64000000L",
-    "hwids": [
-      ["0x2886", "0x1668"],
-      ["0x2886", "0x1667"]
-    ],
-    "usb_product": "TRACKER L1",
-    "mcu": "nrf52840",
-    "variant": "seeed_wio_tracker_L1",
-    "bsp": {
-      "name": "adafruit"
-    },
-    "softdevice": {
-      "sd_flags": "-DS140",
-      "sd_name": "s140",
-      "sd_version": "7.3.0",
-      "sd_fwid": "0x0123"
-    },
-    "bootloader": {
-      "settings_addr": "0xFF000"
-    }
-  },
-  "connectivity": ["bluetooth"],
-  "debug": {
-    "jlink_device": "nRF52840_xxAA",
-    "svd_path": "nrf52840.svd",
-    "openocd_target": "nrf52840-mdk-rs"
-  },
-  "frameworks": ["arduino"],
-  "name": "seeed_wio_tracker_L1",
-  "upload": {
-    "maximum_ram_size": 248832,
-    "maximum_size": 815104,
-    "speed": 115200,
-    "protocol": "nrfutil",
-    "protocols": [
-      "jlink",
-      "nrfjprog",
-      "nrfutil",
-      "stlink",
-      "cmsis-dap",
-      "blackmagic"
-    ],
-    "use_1200bps_touch": true,
-    "require_upload_port": true,
-    "wait_for_upload_port": true
-  },
-  "url": "https://www.seeedstudio.com/Wio-Tracker-L1-p-6477.html",
-  "vendor": "Seeed Studio"
-}

boards/seeed_xiao_nrf52840_kit.json

@@ -7,7 +7,9 @@
     "cpu": "cortex-m4",
     "extra_flags": "-DARDUINO_MDBT50Q_RX -DNRF52840_XXAA",
     "f_cpu": "64000000L",
-    "hwids": [["0x2886", "0x0166"]],
+    "hwids": [
+      ["0x2886", "0x0166"]
+    ],
     "usb_product": "XIAO-BOOT",
     "mcu": "nrf52840",
     "variant": "seeed_xiao_nrf52840_kit",

boards/t-watch-s3.json

@@ -16,7 +16,6 @@
     "f_cpu": "240000000L",
     "f_flash": "80000000L",
     "flash_mode": "qio",
-    "psram_type": "opi",
     "hwids": [
       ["0x303A", "0x1001"],
       ["0x303A", "0x0002"]
@@ -24,16 +23,16 @@
     "mcu": "esp32s3",
     "variant": "t-watch-s3"
   },
-  "connectivity": ["wifi", "bluetooth", "lora"],
+  "connectivity": ["wifi"],
   "debug": {
     "openocd_target": "esp32s3.cfg"
   },
   "frameworks": ["arduino"],
   "name": "LilyGo T-Watch 2020 V3",
   "upload": {
-    "flash_size": "16MB",
+    "flash_size": "8MB",
     "maximum_ram_size": 327680,
-    "maximum_size": 16777216,
+    "maximum_size": 8388608,
     "require_upload_port": true,
     "use_1200bps_touch": true,
     "wait_for_upload_port": true,

boards/tracker-t1000-e.json

@@ -11,8 +11,7 @@
       ["0x239A", "0x8029"],
       ["0x239A", "0x0029"],
       ["0x239A", "0x002A"],
-      ["0x239A", "0x802A"],
-      ["0x2886", "0x0057"]
+      ["0x239A", "0x802A"]
     ],
     "usb_product": "T1000-E-BOOT",
     "mcu": "nrf52840",

boards/wiscore_rak3312.json

@@ -1,41 +0,0 @@
-{
-  "build": {
-    "arduino": {
-      "ldscript": "esp32s3_out.ld",
-      "memory_type": "qio_opi",
-      "partitions": "default_16MB.csv"
-    },
-    "core": "esp32",
-    "extra_flags": [
-      "-DRAK3312",
-      "-DARDUINO_USB_CDC_ON_BOOT=1",
-      "-DARDUINO_USB_MODE=1",
-      "-DARDUINO_RUNNING_CORE=1",
-      "-DARDUINO_EVENT_RUNNING_CORE=1",
-      "-DBOARD_HAS_PSRAM"
-    ],
-    "f_cpu": "240000000L",
-    "f_flash": "80000000L",
-    "flash_mode": "dio",
-    "hwids": [["0x303A", "0x1001"]],
-    "mcu": "esp32s3",
-    "variant": "rak3312"
-  },
-  "connectivity": ["wifi", "bluetooth"],
-  "debug": {
-    "openocd_target": "esp32s3.cfg"
-  },
-  "frameworks": ["arduino", "espidf"],
-  "name": "WisCore RAK3312 Board",
-  "upload": {
-    "flash_size": "16MB",
-    "maximum_ram_size": 327680,
-    "maximum_size": 16777216,
-    "use_1200bps_touch": true,
-    "wait_for_upload_port": true,
-    "require_upload_port": true,
-    "speed": 921600
-  },
-  "url": "https://www.rakwireless.com/en-us",
-  "vendor": "rakwireless"
-}

branding/README.md

@@ -1,17 +0,0 @@
-# Meshtastic Branding / Whitelabeling
-
-This directory is consumed during the creation of **event** firmware.
-
-`bin/platformio-custom.py` determines the display resolution, and locates the corresponding `logo_<width>x<height>.png`.
-
-Ex:
-
-- `logo_800x480.png`
-- `logo_480x480.png`
-- `logo_480x320.png`
-- `logo_320x480.png`
-- `logo_320x240.png`
-
-This file is copied to `data/boot/logo.png` before filesytem image compilation.
-
-For additional examples see the [`event/defcon33` branch](https://github.com/meshtastic/firmware/tree/event/defcon33).

debian/changelog

@@ -1,34 +1,9 @@
-meshtasticd (2.7.3.0) UNRELEASED; urgency=medium
+meshtasticd (2.5.22.0) UNRELEASED; urgency=medium
 
-  [ Austin Lane ]
   * Initial packaging
   * GitHub Actions Automatic version bump
   * GitHub Actions Automatic version bump
   * GitHub Actions Automatic version bump
   * GitHub Actions Automatic version bump
 
-  [  ]
-  * GitHub Actions Automatic version bump
-
-  [  ]
-  * GitHub Actions Automatic version bump
-
-  [  ]
-  * GitHub Actions Automatic version bump
-
-  [  ]
-  * GitHub Actions Automatic version bump
-
-  [  ]
-  * GitHub Actions Automatic version bump
-
-  [  ]
-  * GitHub Actions Automatic version bump
-
-  [  ]
-  * GitHub Actions Automatic version bump
-
-  [ Ubuntu ]
-  * GitHub Actions Automatic version bump
-
- -- Ubuntu <github-actions[bot]@users.noreply.github.com>  Thu, 10 Jul 2025 16:29:27 +0000
+ -- Austin Lane <github-actions[bot]@users.noreply.github.com>  Wed, 05 Feb 2025 01:10:33 +0000

debian/ci_pack_sdeb.sh

@@ -5,14 +5,13 @@ export PLATFORMIO_PACKAGES_DIR=pio/packages
 export PLATFORMIO_CORE_DIR=pio/core
 
 # Download libraries to `pio`
-platformio pkg install -e native-tft
-platformio pkg install -e native-tft -t platformio/tool-scons@4.40502.0
+platformio pkg install -e native
+platformio pkg install -e native -t platformio/tool-scons@4.40502.0
 # Compress `pio` directory to prevent dh_clean from sanitizing it
 tar -cf pio.tar pio/
 rm -rf pio
-# Download the meshtastic/web release build.tar to `web.tar`
-web_ver=$(cat bin/web.version)
-curl -L "https://github.com/meshtastic/web/releases/download/v$web_ver/build.tar" -o web.tar
+# Download the latest meshtastic/web release build.tar to `web.tar`
+curl -L https://github.com/meshtastic/web/releases/latest/download/build.tar -o web.tar
 
 package=$(dpkg-parsechangelog --show-field Source)
 

debian/control

@@ -21,19 +21,14 @@ Build-Depends: debhelper-compat (= 13),
                openssl,
                libssl-dev,
                libulfius-dev,
-               liborcania-dev,
-               libx11-dev,
-               libinput-dev,
-               libxkbcommon-x11-dev
+               liborcania-dev
 Standards-Version: 4.6.2
 Homepage: https://github.com/meshtastic/firmware
 Rules-Requires-Root: no
 
 Package: meshtasticd
 Architecture: any
-Depends: adduser,
-         ${misc:Depends},
-         ${shlibs:Depends}
+Depends: ${misc:Depends}, ${shlibs:Depends}
 Description: Meshtastic daemon for communicating with Meshtastic devices
  Meshtastic is an off-grid text communication platform that uses inexpensive 
- LoRa radios.
+ LoRa radios.

debian/meshtasticd.dirs

@@ -1,6 +1,5 @@
-var/lib/meshtasticd
 etc/meshtasticd
 etc/meshtasticd/config.d
 etc/meshtasticd/available.d
 usr/share/meshtasticd/web
-etc/meshtasticd/ssl
+etc/meshtasticd/ssl

debian/meshtasticd.install

@@ -1,8 +1,8 @@
-.pio/build/native-tft/meshtasticd  usr/bin
+.pio/build/native/meshtasticd  usr/sbin
 
-bin/config.yaml                    etc/meshtasticd
-bin/config.d/*                     etc/meshtasticd/available.d
+bin/config.yaml                etc/meshtasticd
+bin/config.d/*                 etc/meshtasticd/available.d
 
-bin/meshtasticd.service            lib/systemd/system
+bin/meshtasticd.service        lib/systemd/system
 
-web/*                              usr/share/meshtasticd/web
+web/*                          usr/share/meshtasticd/web

debian/meshtasticd.postinst

@@ -1,80 +0,0 @@
-#!/bin/sh
-# postinst script for meshtasticd
-#
-# see: dh_installdeb(1)
-
-set -e
-
-# summary of how this script can be called:
-#        * <postinst> `configure' <most-recently-configured-version>
-#        * <old-postinst> `abort-upgrade' <new version>
-#        * <conflictor's-postinst> `abort-remove' `in-favour' <package>
-#          <new-version>
-#        * <postinst> `abort-remove'
-#        * <deconfigured's-postinst> `abort-deconfigure' `in-favour'
-#          <failed-install-package> <version> `removing'
-#          <conflicting-package> <version>
-# for details, see http://www.debian.org/doc/debian-policy/ or
-# the debian-policy package
-
-
-case "$1" in
-    configure|reconfigure)
-    # create spi, gpio groups (for udev rules)
-    # these groups already exist on Raspberry Pi OS
-        getent group spi >/dev/null 2>/dev/null || addgroup --system spi
-        getent group gpio >/dev/null 2>/dev/null || addgroup --system gpio
-    # create a meshtasticd group and user
-        getent passwd meshtasticd >/dev/null 2>/dev/null || adduser --system --home /var/lib/meshtasticd --no-create-home meshtasticd
-        getent group meshtasticd >/dev/null 2>/dev/null || addgroup --system meshtasticd
-        adduser meshtasticd meshtasticd >/dev/null 2>/dev/null
-        adduser meshtasticd spi >/dev/null 2>/dev/null
-        adduser meshtasticd gpio >/dev/null 2>/dev/null
-    # add meshtasticd user to appropriate groups (if they exist)
-        getent group plugdev >/dev/null 2>/dev/null && adduser meshtasticd plugdev >/dev/null 2>/dev/null
-        getent group dialout >/dev/null 2>/dev/null && adduser meshtasticd dialout >/dev/null 2>/dev/null
-        getent group i2c >/dev/null 2>/dev/null && adduser meshtasticd i2c >/dev/null 2>/dev/null
-        getent group video >/dev/null 2>/dev/null && adduser meshtasticd video >/dev/null 2>/dev/null
-        getent group audio >/dev/null 2>/dev/null && adduser meshtasticd audio >/dev/null 2>/dev/null
-        getent group input >/dev/null 2>/dev/null && adduser meshtasticd input >/dev/null 2>/dev/null
-
-
-    # migrate /root/.portduino to /var/lib/meshtasticd/.portduino
-    # should only run once, upon upgrade from < 2.6.9
-    if [ -n "$2" ] && dpkg --compare-versions "$2" lt 2.6.9; then
-        if [ -d /root/.portduino ] && [ ! -e /var/lib/meshtasticd/.portduino ]; then
-            cp -r /root/.portduino /var/lib/meshtasticd/.portduino
-            echo "Migrated meshtasticd VFS from /root/.portduino to /var/lib/meshtasticd/.portduino"
-            echo "meshtasticd now runs as the 'meshtasticd' user, not 'root'."
-            echo "See https://github.com/meshtastic/firmware/pull/6718 for details"
-        fi
-    fi
-
-    if [ -d /var/lib/meshtasticd ]; then
-        chown -R meshtasticd:meshtasticd /var/lib/meshtasticd
-    fi
-
-    if [ -d /etc/meshtasticd ]; then
-        chown -R meshtasticd:meshtasticd /etc/meshtasticd
-    fi
-
-    if [ -d /usr/share/meshtasticd ]; then
-        chown -R meshtasticd:meshtasticd /usr/share/meshtasticd
-    fi
-    ;;
-
-    abort-upgrade|abort-remove|abort-deconfigure)
-    ;;
-
-    *)
-        echo "postinst called with unknown argument \`$1'" >&2
-        exit 1
-    ;;
-esac
-
-# dh_installdeb will replace this with shell code automatically
-# generated by other debhelper scripts.
-
-#DEBHELPER#
-
-exit 0

debian/meshtasticd.postrm

@@ -1,41 +0,0 @@
-#!/bin/sh
-# postrm script for meshtasticd
-#
-# see: dh_installdeb(1)
-
-set -e
-
-# summary of how this script can be called:
-#        * <postrm> `remove'
-#        * <postrm> `purge'
-#        * <old-postrm> `upgrade' <new-version>
-#        * <new-postrm> `failed-upgrade' <old-version>
-#        * <new-postrm> `abort-install'
-#        * <new-postrm> `abort-install' <old-version>
-#        * <new-postrm> `abort-upgrade' <old-version>
-#        * <disappearer's-postrm> `disappear' <overwriter>
-#          <overwriter-version>
-# for details, see http://www.debian.org/doc/debian-policy/ or
-# the debian-policy package
-
-
-case "$1" in
-    purge|remove|upgrade|failed-upgrade|abort-install|abort-upgrade|disappear)
-      # Only remove /var/lib/meshtasticd on purge
-      if [ "${1}" = "purge" ] ; then
-          rm -rf /var/lib/meshtasticd
-      fi
-    ;;
-
-    *)
-        echo "postrm called with unknown argument \`$1'" >&2
-        exit 1
-    ;;
-esac
-
-# dh_installdeb will replace this with shell code automatically
-# generated by other debhelper scripts.
-
-#DEBHELPER#
-
-exit 0

debian/meshtasticd.udev

@@ -1,7 +0,0 @@
-# Set spidev ownership to 'spi' group
-SUBSYSTEM=="spidev", KERNEL=="spidev*", GROUP="spi", MODE="0660"
-# Allow access to USB CH341 devices
-SUBSYSTEM=="usb", ATTRS{idVendor}=="1a86", ATTRS{idProduct}=="5512", MODE="0666"
-# Set gpio ownership to 'gpio' group
-SUBSYSTEM=="*gpiomem*", GROUP="gpio", MODE="0660"
-SUBSYSTEM=="gpio", GROUP="gpio", MODE="0660"

debian/rules

@@ -26,7 +26,7 @@ override_dh_auto_build:
 	mkdir -p web && tar -xf web.tar -C web
 	gunzip web/ -r
 	# Build with platformio
-	$(PIO_ENV) platformio run -e native-tft
+	$(PIO_ENV) platformio run -e native
 	# Move the binary and default config to the correct name
-	mv .pio/build/native-tft/program .pio/build/native-tft/meshtasticd
+	mv .pio/build/native/program .pio/build/native/meshtasticd
 	cp bin/config-dist.yaml bin/config.yaml