CLIENT_BASE: Act like ROUTER_LATE for fav'd nodes, instead of like ROUTER (#8567)

* Client_Base - Dont rebroadcast in early (Router) window

Removed early rebroadcast check for CLIENT_BASE role.

* Client_Base - Clamp rebroadcast to late (Router_Late) window on dupe

* Only clamp to Router_Late window if packet from fav'd node

---------

Co-authored-by: Ben Meadors <benmmeadors@gmail.com>

.github/workflows/build_firmware.yml

@@ -56,16 +56,18 @@ jobs:
           ota_firmware_source: ${{ steps.ota_dir.outputs.src || '' }}
           ota_firmware_target: ${{ steps.ota_dir.outputs.tgt || '' }}
 
-      - name: Echo manifest from release/firmware-*.mt.json to job summary
-        if: ${{ always() }}
+      - name: Job summary
         env:
           PIO_ENV: ${{ inputs.pio_env }}
         run: |
-          echo "## Manifest: \`$PIO_ENV\`" >> $GITHUB_STEP_SUMMARY
+          echo "## $PIO_ENV" >> $GITHUB_STEP_SUMMARY
+          echo "<details><summary><strong>Manifest</strong></summary>" >> $GITHUB_STEP_SUMMARY
+          echo '' >> $GITHUB_STEP_SUMMARY
           echo '```json' >> $GITHUB_STEP_SUMMARY
           cat release/firmware-*.mt.json >> $GITHUB_STEP_SUMMARY
           echo '' >> $GITHUB_STEP_SUMMARY
           echo '```' >> $GITHUB_STEP_SUMMARY
+          echo "</details>" >> $GITHUB_STEP_SUMMARY
 
       - name: Store binaries as an artifact
         uses: actions/upload-artifact@v6

.trunk/trunk.yaml

@@ -9,14 +9,14 @@ plugins:
 lint:
   enabled:
     - checkov@3.2.495
-    - renovate@42.64.1
+    - renovate@42.57.1
     - prettier@3.7.4
     - trufflehog@3.92.3
     - yamllint@1.37.1
     - bandit@1.9.2
-    - trivy@0.68.2
+    - trivy@0.68.1
     - taplo@0.10.0
-    - ruff@0.14.10
+    - ruff@0.14.9
     - isort@7.0.0
     - markdownlint@0.47.0
     - oxipng@10.0.0

platformio.ini

@@ -103,17 +103,13 @@ lib_deps =
 	thingsboard/TBPubSubClient@2.12.1
 	# renovate: datasource=custom.pio depName=NTPClient packageName=arduino-libraries/library/NTPClient
 	arduino-libraries/NTPClient@3.2.1
+
+; Extra TCP/IP networking libs for supported devices
+[networking_extra]
+lib_deps =
 	# renovate: datasource=custom.pio depName=Syslog packageName=arcao/library/Syslog
 	arcao/Syslog@2.0.0
 
-; Minimal networking libs for nrf52 (excludes Syslog to save flash)
-[nrf52_networking_base]
-lib_deps =
-	# renovate: datasource=custom.pio depName=TBPubSubClient packageName=thingsboard/library/TBPubSubClient
-	thingsboard/TBPubSubClient@2.12.1
-	# renovate: datasource=custom.pio depName=NTPClient packageName=arduino-libraries/library/NTPClient
-	arduino-libraries/NTPClient@3.2.1
-
 [radiolib_base]
 lib_deps =
 	# renovate: datasource=custom.pio depName=RadioLib packageName=jgromes/library/RadioLib
@@ -162,8 +158,8 @@ lib_deps =
 	emotibit/EmotiBit MLX90632@1.0.8
 	# renovate: datasource=custom.pio depName=Adafruit MLX90614 packageName=adafruit/library/Adafruit MLX90614 Library
 	adafruit/Adafruit MLX90614 Library@2.1.5
-	# renovate: datasource=github-tags depName=INA3221 packageName=sgtwilko/INA3221
-	https://github.com/sgtwilko/INA3221#bb03d7e9bfcc74fc798838a54f4f99738f29fc6a
+	# renovate: datasource=git-refs depName=INA3221 packageName=https://github.com/sgtwilko/INA3221 gitBranch=FixOverflow
+	https://github.com/sgtwilko/INA3221/archive/bb03d7e9bfcc74fc798838a54f4f99738f29fc6a.zip
 	# renovate: datasource=custom.pio depName=QMC5883L Compass packageName=mprograms/library/QMC5883LCompass
 	mprograms/QMC5883LCompass@1.2.3
 	# renovate: datasource=custom.pio depName=DFRobot_RTU packageName=dfrobot/library/DFRobot_RTU

src/graphics/niche/InkHUD/PlatformioConfig.ini

@@ -8,4 +8,5 @@ build_flags =
   -D MESHTASTIC_EXCLUDE_INPUTBROKER ; Suppress default input handling
   -D HAS_BUTTON=0 ; Suppress default ButtonThread
 lib_deps =
-  https://github.com/ZinggJM/GFX_Root#2.0.0 ; Used by InkHUD as a "slimmer" version of AdafruitGFX
+  # TODO renovate
+  https://github.com/ZinggJM/GFX_Root#2.0.0 ; Used by InkHUD as a "slimmer" version of AdafruitGFX

src/main.cpp

@@ -428,10 +428,17 @@ void setup()
 #endif
 
 #if ARCH_PORTDUINO
+    RTCQuality ourQuality = RTCQualityDevice;
+
+    std::string timeCommandResult = exec("timedatectl status | grep synchronized | grep yes -c");
+    if (timeCommandResult[0] == '1') {
+        ourQuality = RTCQualityNTP;
+    }
+
     struct timeval tv;
     tv.tv_sec = time(NULL);
     tv.tv_usec = 0;
-    perhapsSetRTC(RTCQualityDevice, &tv);
+    perhapsSetRTC(ourQuality, &tv);
 #endif
 
     powerMonInit();
@@ -440,9 +447,11 @@ void setup()
     LOG_INFO("\n\n//\\ E S H T /\\ S T / C\n");
 
 #if defined(ARCH_ESP32) && defined(BOARD_HAS_PSRAM)
+#ifndef SENSECAP_INDICATOR
     // use PSRAM for malloc calls > 256 bytes
     heap_caps_malloc_extmem_enable(256);
 #endif
+#endif
 
 #if defined(DEBUG_MUTE) && defined(DEBUG_PORT)
     DEBUG_PORT.printf("\r\n\r\n//\\ E S H T /\\ S T / C\r\n");

src/mesh/Channels.h

@@ -96,6 +96,8 @@ class Channels
 
     bool setDefaultPresetCryptoForHash(ChannelHash channelHash);
 
+    int16_t getHash(ChannelIndex i) { return hashes[i]; }
+
   private:
     /** Given a channel index, change to use the crypto key specified by that index
      *
@@ -113,8 +115,6 @@ class Channels
      */
     int16_t generateHash(ChannelIndex channelNum);
 
-    int16_t getHash(ChannelIndex i) { return hashes[i]; }
-
     /**
      * Validate a channel, fixing any errors as needed
      */

src/mesh/FloodingRouter.cpp

@@ -124,6 +124,9 @@ void FloodingRouter::perhapsCancelDupe(const meshtastic_MeshPacket *p)
     if (config.device.role == meshtastic_Config_DeviceConfig_Role_ROUTER_LATE && iface) {
         iface->clampToLateRebroadcastWindow(getFrom(p), p->id);
     }
+    if (config.device.role == meshtastic_Config_DeviceConfig_Role_CLIENT_BASE && iface && nodeDB && nodeDB->isFromOrToFavoritedNode(*p)) {
+        iface->clampToLateRebroadcastWindow(getFrom(p), p->id);
+    }
 }
 
 bool FloodingRouter::isRebroadcaster()

src/mesh/NodeDB.cpp

@@ -805,11 +805,11 @@ void NodeDB::installDefaultModuleConfig()
     moduleConfig.external_notification.output_ms = 500;
     moduleConfig.external_notification.nag_timeout = 2;
 #endif
-#if defined(RAK4630) || defined(RAK11310) || defined(RAK3312) || defined(MUZI_BASE) || defined(ELECROW_ThinkNode_M3)
-    // Default to PIN_LED2 for external notification output (LED color depends on device variant)
+#if defined(RAK4630) || defined(RAK11310) || defined(RAK3312) || defined(MUZI_BASE)
+    // Default to RAK led pin 2 (blue)
     moduleConfig.external_notification.enabled = true;
     moduleConfig.external_notification.output = PIN_LED2;
-#if defined(MUZI_BASE) || defined(ELECROW_ThinkNode_M3)
+#if defined(MUZI_BASE)
     moduleConfig.external_notification.active = false;
 #else
     moduleConfig.external_notification.active = true;

src/mesh/RadioInterface.cpp

@@ -296,11 +296,6 @@ bool RadioInterface::shouldRebroadcastEarlyLikeRouter(meshtastic_MeshPacket *p)
         return true;
     }
 
-    // If we are a CLIENT_BASE and the packet is from or to a favorited node, we should rebroadcast early
-    if (config.device.role == meshtastic_Config_DeviceConfig_Role_CLIENT_BASE) {
-        return nodeDB->isFromOrToFavoritedNode(*p);
-    }
-
     return false;
 }
 

src/mesh/Router.cpp

@@ -692,7 +692,7 @@ void Router::handleReceived(meshtastic_MeshPacket *p, RxSource src)
 
     // Store a copy of encrypted packet for MQTT
     DEBUG_HEAP_BEFORE;
-    meshtastic_MeshPacket *p_encrypted = packetPool.allocCopy(*p);
+    p_encrypted = packetPool.allocCopy(*p);
     DEBUG_HEAP_AFTER("Router::handleReceived", p_encrypted);
 
     // Take those raw bytes and convert them back into a well structured protobuf we can understand
@@ -758,6 +758,7 @@ void Router::handleReceived(meshtastic_MeshPacket *p, RxSource src)
     }
 
     packetPool.release(p_encrypted); // Release the encrypted packet
+    p_encrypted = nullptr;
 }
 
 void Router::perhapsHandleReceived(meshtastic_MeshPacket *p)

src/mesh/Router.h

@@ -91,6 +91,9 @@ class Router : protected concurrency::OSThread, protected PacketHistory
         before us */
     uint32_t rxDupe = 0, txRelayCanceled = 0;
 
+    // pointer to the encrypted packet
+    meshtastic_MeshPacket *p_encrypted = nullptr;
+
   protected:
     friend class RoutingModule;
 

src/modules/AdminModule.cpp

@@ -417,6 +417,9 @@ bool AdminModule::handleReceivedProtobuf(const meshtastic_MeshPacket &mp, meshta
     }
     case meshtastic_AdminMessage_enter_dfu_mode_request_tag: {
         LOG_INFO("Client requesting to enter DFU mode");
+#if HAS_SCREEN
+        IF_SCREEN(screen->showSimpleBanner("Device is rebooting\ninto DFU mode.", 0));
+#endif
 #if defined(ARCH_NRF52) || defined(ARCH_RP2040)
         enterDfuMode();
 #endif

src/modules/StatusLEDModule.cpp

@@ -26,11 +26,7 @@ int StatusLEDModule::handleStatusUpdate(const meshtastic::Status *arg)
                 power_state = charged;
             }
         } else {
-            if (powerStatus->getBatteryChargePercent() > 5) {
-                power_state = discharging;
-            } else {
-                power_state = critical;
-            }
+            power_state = discharging;
         }
         break;
     }
@@ -62,33 +58,16 @@ int StatusLEDModule::handleStatusUpdate(const meshtastic::Status *arg)
 
 int32_t StatusLEDModule::runOnce()
 {
-    my_interval = 1000;
 
     if (power_state == charging) {
         CHARGE_LED_state = !CHARGE_LED_state;
     } else if (power_state == charged) {
         CHARGE_LED_state = LED_STATE_ON;
-    } else if (power_state == critical) {
-        if (POWER_LED_starttime + 30000 < millis() && !doing_fast_blink) {
-            doing_fast_blink = true;
-            POWER_LED_starttime = millis();
-        }
-        if (doing_fast_blink) {
-            PAIRING_LED_state = LED_STATE_OFF;
-            CHARGE_LED_state = !CHARGE_LED_state;
-            my_interval = 250;
-            if (POWER_LED_starttime + 2000 < millis()) {
-                doing_fast_blink = false;
-            }
-        } else {
-            CHARGE_LED_state = LED_STATE_OFF;
-        }
-
     } else {
         CHARGE_LED_state = LED_STATE_OFF;
     }
 
-    if (!config.bluetooth.enabled || PAIRING_LED_starttime + 30 * 1000 < millis() || doing_fast_blink) {
+    if (!config.bluetooth.enabled || PAIRING_LED_starttime + 30 * 1000 < millis()) {
         PAIRING_LED_state = LED_STATE_OFF;
     } else if (ble_state == unpaired) {
         if (slowTrack) {

src/modules/StatusLEDModule.h

@@ -31,10 +31,8 @@ class StatusLEDModule : private concurrency::OSThread
     bool PAIRING_LED_state = LED_STATE_OFF;
 
     uint32_t PAIRING_LED_starttime = 0;
-    uint32_t POWER_LED_starttime = 0;
-    bool doing_fast_blink = false;
 
-    enum PowerState { discharging, charging, charged, critical };
+    enum PowerState { discharging, charging, charged };
 
     PowerState power_state = discharging;
 

src/nimble/NimbleBluetooth.cpp

@@ -14,11 +14,11 @@
 #include <atomic>
 #include <mutex>
 
+#ifdef NIMBLE_TWO
 #include "NimBLEAdvertising.h"
-#ifdef CONFIG_BT_NIMBLE_EXT_ADV
 #include "NimBLEExtAdvertising.h"
-#endif
 #include "PowerStatus.h"
+#endif
 
 #if defined(CONFIG_NIMBLE_CPP_IDF)
 #include "host/ble_gap.h"
@@ -26,12 +26,15 @@
 #include "nimble/nimble/host/include/host/ble_gap.h"
 #endif
 
+#if defined(CONFIG_IDF_TARGET_ESP32S3) || defined(CONFIG_IDF_TARGET_ESP32C6)
+
 namespace
 {
 constexpr uint16_t kPreferredBleMtu = 517;
 constexpr uint16_t kPreferredBleTxOctets = 251;
 constexpr uint16_t kPreferredBleTxTimeUs = (kPreferredBleTxOctets + 14) * 8;
 } // namespace
+#endif
 
 // Debugging options: careful, they slow things down quite a bit!
 // #define DEBUG_NIMBLE_ON_READ_TIMING  // uncomment to time onRead duration
@@ -310,9 +313,11 @@ class BluetoothPhoneAPI : public PhoneAPI, public concurrency::OSThread
     {
         PhoneAPI::onNowHasData(fromRadioNum);
 
-#ifdef DEBUG_NIMBLE_NOTIFY
         int currentNotifyCount = notifyCount.fetch_add(1);
+
         uint8_t cc = bleServer->getConnectedCount();
+
+#ifdef DEBUG_NIMBLE_NOTIFY
         // This logging slows things down when there are lots of packets going to the phone, like initial connection:
         LOG_DEBUG("BLE notify(%d) fromNum: %d connections: %d", currentNotifyCount, fromRadioNum, cc);
 #endif
@@ -321,7 +326,13 @@ class BluetoothPhoneAPI : public PhoneAPI, public concurrency::OSThread
         put_le32(val, fromRadioNum);
 
         fromNumCharacteristic->setValue(val, sizeof(val));
+#ifdef NIMBLE_TWO
+        // NOTE: I don't have any NIMBLE_TWO devices, but this line makes me suspicious, and I suspect it needs to just be
+        // notify().
         fromNumCharacteristic->notify(val, sizeof(val), BLE_HS_CONN_HANDLE_NONE);
+#else
+        fromNumCharacteristic->notify();
+#endif
     }
 
     /// Check the current underlying physical link to see if the client is currently connected
@@ -386,7 +397,12 @@ static uint8_t lastToRadio[MAX_TO_FROM_RADIO_SIZE];
 
 class NimbleBluetoothToRadioCallback : public NimBLECharacteristicCallbacks
 {
-    void onWrite(NimBLECharacteristic *pCharacteristic, NimBLEConnInfo &) override
+#ifdef NIMBLE_TWO
+    virtual void onWrite(NimBLECharacteristic *pCharacteristic, NimBLEConnInfo &connInfo)
+#else
+    virtual void onWrite(NimBLECharacteristic *pCharacteristic)
+
+#endif
     {
         // CAUTION: This callback runs in the NimBLE task!!! Don't do anything except communicate with the main task's runOnce.
         // Assumption: onWrite is serialized by NimBLE, so we don't need to lock here against multiple concurrent onWrite calls.
@@ -433,7 +449,11 @@ class NimbleBluetoothToRadioCallback : public NimBLECharacteristicCallbacks
 
 class NimbleBluetoothFromRadioCallback : public NimBLECharacteristicCallbacks
 {
-    void onRead(NimBLECharacteristic *pCharacteristic, NimBLEConnInfo &) override
+#ifdef NIMBLE_TWO
+    virtual void onRead(NimBLECharacteristic *pCharacteristic, NimBLEConnInfo &connInfo)
+#else
+    virtual void onRead(NimBLECharacteristic *pCharacteristic)
+#endif
     {
         // CAUTION: This callback runs in the NimBLE task!!! Don't do anything except communicate with the main task's runOnce.
 
@@ -541,27 +561,32 @@ class NimbleBluetoothFromRadioCallback : public NimBLECharacteristicCallbacks
 
 class NimbleBluetoothServerCallback : public NimBLEServerCallbacks
 {
+#ifdef NIMBLE_TWO
   public:
-    explicit NimbleBluetoothServerCallback(NimbleBluetooth *ble) : ble(ble) {}
+    NimbleBluetoothServerCallback(NimbleBluetooth *ble) { this->ble = ble; }
 
   private:
     NimbleBluetooth *ble;
 
-    uint32_t onPassKeyDisplay() override
+    virtual uint32_t onPassKeyDisplay()
+#else
+    virtual uint32_t onPassKeyRequest()
+#endif
     {
         uint32_t passkey = config.bluetooth.fixed_pin;
 
         if (config.bluetooth.mode == meshtastic_Config_BluetoothConfig_PairingMode_RANDOM_PIN) {
             LOG_INFO("Use random passkey");
+            // This is the passkey to be entered on peer - we pick a number >100,000 to ensure 6 digits
             passkey = random(100000, 999999);
         }
-        LOG_INFO("*** Enter passkey %06u on the peer side ***", passkey);
+        LOG_INFO("*** Enter passkey %d on the peer side ***", passkey);
 
         powerFSM.trigger(EVENT_BLUETOOTH_PAIR);
         meshtastic::BluetoothStatus newStatus(std::to_string(passkey));
         bluetoothStatus->updateStatus(&newStatus);
 
-#if HAS_SCREEN
+#if HAS_SCREEN // Todo: migrate this display code back into Screen class, and observe bluetoothStatus
         if (screen) {
             screen->startAlert([passkey](OLEDDisplay *display, OLEDDisplayUiState *state, int16_t x, int16_t y) -> void {
                 char btPIN[16] = "888888";
@@ -590,29 +615,39 @@ class NimbleBluetoothServerCallback : public NimBLEServerCallbacks
             });
         }
 #endif
-
         passkeyShowing = true;
+
         return passkey;
     }
 
-    void onAuthenticationComplete(NimBLEConnInfo &connInfo) override
+#ifdef NIMBLE_TWO
+    virtual void onAuthenticationComplete(NimBLEConnInfo &connInfo)
+#else
+    virtual void onAuthenticationComplete(ble_gap_conn_desc *desc)
+#endif
     {
         LOG_INFO("BLE authentication complete");
 
         meshtastic::BluetoothStatus newStatus(meshtastic::BluetoothStatus::ConnectionState::CONNECTED);
         bluetoothStatus->updateStatus(&newStatus);
 
+        // Todo: migrate this display code back into Screen class, and observe bluetoothStatus
         if (passkeyShowing) {
             passkeyShowing = false;
-            if (screen) {
+            if (screen)
                 screen->endAlert();
-            }
         }
 
+        // Store the connection handle for future use
+#ifdef NIMBLE_TWO
         nimbleBluetoothConnHandle = connInfo.getConnHandle();
+#else
+        nimbleBluetoothConnHandle = desc->conn_handle;
+#endif
     }
 
-    void onConnect(NimBLEServer *pServer, NimBLEConnInfo &connInfo) override
+#ifdef NIMBLE_TWO
+    virtual void onConnect(NimBLEServer *pServer, NimBLEConnInfo &connInfo)
     {
         LOG_INFO("BLE incoming connection %s", connInfo.getAddress().toString().c_str());
 
@@ -637,12 +672,21 @@ class NimbleBluetoothServerCallback : public NimBLEServerCallbacks
         LOG_INFO("BLE conn %u initial MTU %u (target %u)", connHandle, connInfo.getMTU(), kPreferredBleMtu);
         pServer->updateConnParams(connHandle, 6, 12, 0, 200);
     }
+#endif
 
-    void onDisconnect(NimBLEServer *pServer, NimBLEConnInfo &connInfo, int reason) override
+#ifdef NIMBLE_TWO
+    virtual void onDisconnect(NimBLEServer *pServer, NimBLEConnInfo &connInfo, int reason)
     {
         LOG_INFO("BLE disconnect reason: %d", reason);
+#else
+    virtual void onDisconnect(NimBLEServer *pServer, ble_gap_conn_desc *desc)
+    {
+        LOG_INFO("BLE disconnect");
+#endif
+#ifdef NIMBLE_TWO
         if (ble->isDeInit)
             return;
+#endif
 
         meshtastic::BluetoothStatus newStatus(meshtastic::BluetoothStatus::ConnectionState::DISCONNECTED);
         bluetoothStatus->updateStatus(&newStatus);
@@ -666,69 +710,35 @@ class NimbleBluetoothServerCallback : public NimBLEServerCallbacks
             bluetoothPhoneAPI->writeCount = 0;
         }
 
+        // Clear the last ToRadio packet buffer to avoid rejecting first packet from new connection
         memset(lastToRadio, 0, sizeof(lastToRadio));
 
-        nimbleBluetoothConnHandle = BLE_HS_CONN_HANDLE_NONE;
+        nimbleBluetoothConnHandle = BLE_HS_CONN_HANDLE_NONE; // BLE_HS_CONN_HANDLE_NONE means "no connection"
 
+#ifdef NIMBLE_TWO
+        // Restart Advertising
         ble->startAdvertising();
+#else
+        NimBLEAdvertising *pAdvertising = NimBLEDevice::getAdvertising();
+        if (!pAdvertising->start(0)) {
+            if (pAdvertising->isAdvertising()) {
+                LOG_DEBUG("BLE advertising already running");
+            } else {
+                LOG_ERROR("BLE failed to restart advertising");
+            }
+        }
+#endif
     }
 };
 
 static NimbleBluetoothToRadioCallback *toRadioCallbacks;
 static NimbleBluetoothFromRadioCallback *fromRadioCallbacks;
 
-void NimbleBluetooth::startAdvertising()
-{
-#if defined(CONFIG_BT_NIMBLE_EXT_ADV)
-    NimBLEExtAdvertising *pAdvertising = NimBLEDevice::getAdvertising();
-    NimBLEExtAdvertisement legacyAdvertising;
-
-    legacyAdvertising.setLegacyAdvertising(true);
-    legacyAdvertising.setScannable(true);
-    legacyAdvertising.setConnectable(true);
-    legacyAdvertising.setFlags(BLE_HS_ADV_F_DISC_GEN);
-    if (powerStatus->getHasBattery() == 1) {
-        legacyAdvertising.setCompleteServices(NimBLEUUID((uint16_t)0x180f));
-    }
-    legacyAdvertising.setCompleteServices(NimBLEUUID(MESH_SERVICE_UUID));
-    legacyAdvertising.setMinInterval(500);
-    legacyAdvertising.setMaxInterval(1000);
-
-    NimBLEExtAdvertisement legacyScanResponse;
-    legacyScanResponse.setLegacyAdvertising(true);
-    legacyScanResponse.setConnectable(true);
-    legacyScanResponse.setName(getDeviceName());
-
-    if (!pAdvertising->setInstanceData(0, legacyAdvertising)) {
-        LOG_ERROR("BLE failed to set legacyAdvertising");
-    } else if (!pAdvertising->setScanResponseData(0, legacyScanResponse)) {
-        LOG_ERROR("BLE failed to set legacyScanResponse");
-    } else if (!pAdvertising->start(0, 0, 0)) {
-        LOG_ERROR("BLE failed to start legacyAdvertising");
-    }
-#else
-    NimBLEAdvertising *pAdvertising = NimBLEDevice::getAdvertising();
-    pAdvertising->reset();
-    pAdvertising->addServiceUUID(MESH_SERVICE_UUID);
-    if (powerStatus->getHasBattery() == 1) {
-        pAdvertising->addServiceUUID(NimBLEUUID((uint16_t)0x180f));
-    }
-
-    NimBLEAdvertisementData scan;
-    scan.setName(getDeviceName());
-    pAdvertising->setScanResponseData(scan);
-    pAdvertising->enableScanResponse(true);
-
-    if (!pAdvertising->start(0)) {
-        LOG_ERROR("BLE failed to start advertising");
-    }
-#endif
-    LOG_DEBUG("BLE Advertising started");
-}
-
 void NimbleBluetooth::shutdown()
 {
+    // No measurable power saving for ESP32 during light-sleep(?)
 #ifndef ARCH_ESP32
+    // Shutdown bluetooth for minimum power draw
     LOG_INFO("Disable bluetooth");
     NimBLEAdvertising *pAdvertising = NimBLEDevice::getAdvertising();
     pAdvertising->reset();
@@ -736,6 +746,7 @@ void NimbleBluetooth::shutdown()
 #endif
 }
 
+// Proper shutdown for ESP32. Needs reboot to reverse.
 void NimbleBluetooth::deinit()
 {
 #ifdef ARCH_ESP32
@@ -749,17 +760,21 @@ void NimbleBluetooth::deinit()
     digitalWrite(BLE_LED, LOW);
 #endif
 #endif
+#ifndef NIMBLE_TWO
+    NimBLEDevice::deinit();
+#endif
 #endif
 }
 
+// Has initial setup been completed
 bool NimbleBluetooth::isActive()
 {
-    return bleServer != nullptr;
+    return bleServer;
 }
 
 bool NimbleBluetooth::isConnected()
 {
-    return bleServer && bleServer->getConnectedCount() > 0;
+    return bleServer->getConnectedCount() > 0;
 }
 
 int NimbleBluetooth::getRssi()
@@ -803,7 +818,7 @@ void NimbleBluetooth::setup()
     LOG_INFO("Init the NimBLE bluetooth module");
 
     NimBLEDevice::init(getDeviceName());
-    NimBLEDevice::setPower(9);
+    NimBLEDevice::setPower(ESP_PWR_LVL_P9);
 
 #if NIMBLE_ENABLE_2M_PHY && (defined(CONFIG_IDF_TARGET_ESP32S3) || defined(CONFIG_IDF_TARGET_ESP32C6))
     int mtuResult = NimBLEDevice::setMTU(kPreferredBleMtu);
@@ -836,7 +851,11 @@ void NimbleBluetooth::setup()
         NimBLEDevice::setSecurityIOCap(BLE_HS_IO_DISPLAY_ONLY);
     }
     bleServer = NimBLEDevice::createServer();
-    auto *serverCallbacks = new NimbleBluetoothServerCallback(this);
+#ifdef NIMBLE_TWO
+    NimbleBluetoothServerCallback *serverCallbacks = new NimbleBluetoothServerCallback(this);
+#else
+    NimbleBluetoothServerCallback *serverCallbacks = new NimbleBluetoothServerCallback();
+#endif
     bleServer->setCallbacks(serverCallbacks, true);
     setupService();
     startAdvertising();
@@ -881,7 +900,11 @@ void NimbleBluetooth::setupService()
     NimBLEService *batteryService = bleServer->createService(NimBLEUUID((uint16_t)0x180f)); // 0x180F is the Battery Service
     BatteryCharacteristic = batteryService->createCharacteristic( // 0x2A19 is the Battery Level characteristic)
         (uint16_t)0x2a19, NIMBLE_PROPERTY::READ | NIMBLE_PROPERTY::NOTIFY, 1);
+#ifdef NIMBLE_TWO
     NimBLE2904 *batteryLevelDescriptor = BatteryCharacteristic->create2904();
+#else
+    NimBLE2904 *batteryLevelDescriptor = (NimBLE2904 *)BatteryCharacteristic->createDescriptor((uint16_t)0x2904);
+#endif
     batteryLevelDescriptor->setFormat(NimBLE2904::FORMAT_UINT8);
     batteryLevelDescriptor->setNamespace(1);
     batteryLevelDescriptor->setUnit(0x27ad);
@@ -889,12 +912,54 @@ void NimbleBluetooth::setupService()
     batteryService->start();
 }
 
+void NimbleBluetooth::startAdvertising()
+{
+#ifdef NIMBLE_TWO
+    NimBLEExtAdvertising *pAdvertising = NimBLEDevice::getAdvertising();
+    NimBLEExtAdvertisement legacyAdvertising;
+
+    legacyAdvertising.setLegacyAdvertising(true);
+    legacyAdvertising.setScannable(true);
+    legacyAdvertising.setConnectable(true);
+    legacyAdvertising.setFlags(BLE_HS_ADV_F_DISC_GEN);
+    if (powerStatus->getHasBattery() == 1) {
+        legacyAdvertising.setCompleteServices(NimBLEUUID((uint16_t)0x180f));
+    }
+    legacyAdvertising.setCompleteServices(NimBLEUUID(MESH_SERVICE_UUID));
+    legacyAdvertising.setMinInterval(500);
+    legacyAdvertising.setMaxInterval(1000);
+
+    NimBLEExtAdvertisement legacyScanResponse;
+    legacyScanResponse.setLegacyAdvertising(true);
+    legacyScanResponse.setConnectable(true);
+    legacyScanResponse.setName(getDeviceName());
+
+    if (!pAdvertising->setInstanceData(0, legacyAdvertising)) {
+        LOG_ERROR("BLE failed to set legacyAdvertising");
+    } else if (!pAdvertising->setScanResponseData(0, legacyScanResponse)) {
+        LOG_ERROR("BLE failed to set legacyScanResponse");
+    } else if (!pAdvertising->start(0, 0, 0)) {
+        LOG_ERROR("BLE failed to start legacyAdvertising");
+    }
+#else
+    NimBLEAdvertising *pAdvertising = NimBLEDevice::getAdvertising();
+    pAdvertising->reset();
+    pAdvertising->addServiceUUID(MESH_SERVICE_UUID);
+    pAdvertising->addServiceUUID(NimBLEUUID((uint16_t)0x180f)); // 0x180F is the Battery Service
+    pAdvertising->start(0);
+#endif
+}
+
 /// Given a level between 0-100, update the BLE attribute
 void updateBatteryLevel(uint8_t level)
 {
     if ((config.bluetooth.enabled == true) && bleServer && nimbleBluetooth->isConnected()) {
         BatteryCharacteristic->setValue(&level, 1);
+#ifdef NIMBLE_TWO
         BatteryCharacteristic->notify(&level, 1, BLE_HS_CONN_HANDLE_NONE);
+#else
+        BatteryCharacteristic->notify();
+#endif
     }
 }
 
@@ -909,7 +974,11 @@ void NimbleBluetooth::sendLog(const uint8_t *logMessage, size_t length)
     if (!bleServer || !isConnected() || length > 512) {
         return;
     }
+#ifdef NIMBLE_TWO
     logRadioCharacteristic->notify(logMessage, length, BLE_HS_CONN_HANDLE_NONE);
+#else
+    logRadioCharacteristic->notify(logMessage, length, true);
+#endif
 }
 
 void clearNVS()

src/nimble/NimbleBluetooth.h

@@ -12,11 +12,16 @@ class NimbleBluetooth : BluetoothApi
     bool isConnected();
     int getRssi();
     void sendLog(const uint8_t *logMessage, size_t length);
+#if defined(NIMBLE_TWO)
     void startAdvertising();
+#endif
     bool isDeInit = false;
 
   private:
     void setupService();
+#if !defined(NIMBLE_TWO)
+    void startAdvertising();
+#endif
 };
 
 void setBluetoothEnable(bool enable);

variants/esp32/betafpv_2400_tx_micro/platformio.ini

@@ -15,4 +15,5 @@ upload_protocol = esptool
 upload_speed = 460800
 lib_deps =
   ${esp32_base.lib_deps}
-  adafruit/Adafruit NeoPixel @ ^1.12.0
+  # renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
+  adafruit/Adafruit NeoPixel@1.15.2

variants/esp32/betafpv_900_tx_nano/platformio.ini

@@ -13,5 +13,3 @@ board_build.f_cpu = 240000000L
 upload_protocol = esptool
 ;upload_port = /dev/ttyUSB0
 upload_speed = 460800
-lib_deps =
-  ${esp32_base.lib_deps}

variants/esp32/chatter2/platformio.ini

@@ -9,4 +9,5 @@ build_flags =
   
 lib_deps =
   ${esp32_base.lib_deps}
-  lovyan03/LovyanGFX@^1.2.0
+  # renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
+  lovyan03/LovyanGFX@1.2.7

variants/esp32/esp32.ini

@@ -38,7 +38,6 @@ build_flags =
   -DAXP_DEBUG_PORT=Serial
   -DCONFIG_BT_NIMBLE_ENABLED
   -DCONFIG_BT_NIMBLE_MAX_BONDS=6 # default is 3
-  -DCONFIG_BT_NIMBLE_ROLE_CENTRAL_DISABLED
   -DCONFIG_NIMBLE_CPP_LOG_LEVEL=2
   -DCONFIG_BT_NIMBLE_MAX_CCCDS=20
   -DCONFIG_BT_NIMBLE_HOST_TASK_STACK_SIZE=8192
@@ -54,17 +53,18 @@ build_flags =
 lib_deps =
   ${arduino_base.lib_deps}
   ${networking_base.lib_deps}
+  ${networking_extra.lib_deps}
   ${environmental_base.lib_deps}
   ${environmental_extra.lib_deps}
   ${radiolib_base.lib_deps}
   # renovate: datasource=git-refs depName=meshtastic-esp32_https_server packageName=https://github.com/meshtastic/esp32_https_server gitBranch=master
   https://github.com/meshtastic/esp32_https_server/archive/3223704846752e6d545139204837bdb2a55459ca.zip
   # renovate: datasource=custom.pio depName=NimBLE-Arduino packageName=h2zero/library/NimBLE-Arduino
-  h2zero/NimBLE-Arduino@^2.3.7
+  h2zero/NimBLE-Arduino@1.4.3
   # renovate: datasource=git-refs depName=libpax packageName=https://github.com/dbinfrago/libpax gitBranch=master
   https://github.com/dbinfrago/libpax/archive/3cdc0371c375676a97967547f4065607d4c53fd1.zip
-  # renovate: datasource=github-tags depName=XPowersLib packageName=lewisxhe/XPowersLib
-  https://github.com/lewisxhe/XPowersLib/archive/v0.3.2.zip
+  # renovate: datasource=custom.pio depName=XPowersLib packageName=lewisxhe/library/XPowersLib
+  lewisxhe/XPowersLib@0.3.2
   # renovate: datasource=git-refs depName=meshtastic-ESP32_Codec2 packageName=https://github.com/meshtastic/ESP32_Codec2 gitBranch=master
   https://github.com/meshtastic/ESP32_Codec2/archive/633326c78ac251c059ab3a8c430fcdf25b41672f.zip
   # renovate: datasource=custom.pio depName=rweather/Crypto packageName=rweather/library/Crypto

variants/esp32/m5stack_core/platformio.ini

@@ -25,4 +25,5 @@ lib_ignore =
   m5stack-core
 lib_deps = 
   ${esp32_base.lib_deps}
-  lovyan03/LovyanGFX@^1.2.0
+  # renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
+  lovyan03/LovyanGFX@1.2.7

variants/esp32/m5stack_coreink/platformio.ini

@@ -18,8 +18,10 @@ build_flags =
   -DM5STACK
 lib_deps = 
   ${esp32_base.lib_deps}
-  zinggjm/GxEPD2@^1.6.2
-  lewisxhe/PCF8563_Library@^1.0.1
+  # renovate: datasource=custom.pio depName=GxEPD2 packageName=zinggjm/library/GxEPD2
+  zinggjm/GxEPD2@1.6.5
+  # renovate: datasource=custom.pio depName=PCF8563 packageName=lewisxhe/library/PCF8563_Library
+  lewisxhe/PCF8563_Library@1.0.1
 lib_ignore =
   m5stack-coreink
 monitor_filters = esp32_exception_decoder

variants/esp32/nano-g1-explorer/platformio.ini

@@ -2,8 +2,6 @@
 [env:nano-g1-explorer]
 extends = esp32_base
 board = ttgo-t-beam
-lib_deps =
-  ${esp32_base.lib_deps}
 build_flags = 
   ${esp32_base.build_flags}
   -D NANO_G1_EXPLORER

variants/esp32/nano-g1/platformio.ini

@@ -2,8 +2,6 @@
 [env:nano-g1]
 extends = esp32_base
 board = ttgo-t-beam
-lib_deps =
-  ${esp32_base.lib_deps}
 build_flags = 
   ${esp32_base.build_flags}
   -D NANO_G1

variants/esp32/radiomaster_900_bandit/platformio.ini

@@ -13,4 +13,5 @@ board_build.f_cpu = 240000000L
 upload_protocol = esptool
 lib_deps =
   ${esp32_base.lib_deps}
+  # renovate: datasource=github-tags depName=STK8xxx-Accelerometer packageName=gjelsoe/STK8xxx-Accelerometer
   https://github.com/gjelsoe/STK8xxx-Accelerometer/archive/v0.1.1.zip

variants/esp32/radiomaster_900_bandit_micro/platformio.ini

@@ -15,5 +15,3 @@ build_flags =
   -I variants/esp32/radiomaster_900_bandit_nano
 board_build.f_cpu = 240000000L
 upload_protocol = esptool
-lib_deps =
-  ${esp32_base.lib_deps}

variants/esp32/radiomaster_900_bandit_nano/platformio.ini

@@ -10,5 +10,3 @@ build_flags =
   -I variants/esp32/radiomaster_900_bandit_nano
 board_build.f_cpu = 240000000L
 upload_protocol = esptool
-lib_deps =
-  ${esp32_base.lib_deps}

variants/esp32/station-g1/platformio.ini

@@ -2,8 +2,6 @@
 [env:station-g1]
 extends = esp32_base
 board = ttgo-t-beam
-lib_deps =
-  ${esp32_base.lib_deps}
 build_flags = 
   ${esp32_base.build_flags}
   -D STATION_G1

variants/esp32/tbeam/platformio.ini

@@ -4,7 +4,6 @@ extends = esp32_base
 board = ttgo-t-beam
 board_level = extra
 board_check = true
-lib_deps = ${esp32_base.lib_deps}
 build_flags = ${esp32_base.build_flags}
   -D TBEAM_V10
   -I variants/esp32/tbeam
@@ -21,5 +20,7 @@ build_flags =
 
 lib_deps =
   ${env:tbeam.lib_deps}
-  https://github.com/meshtastic/st7796/archive/refs/tags/1.0.5.zip ; display addon
-  lewisxhe/SensorLib@0.3.1 ; touchscreen addon
+  # renovate: datasource=github-tags depName=meshtastic-st7796 packageName=meshtastic/st7796
+  https://github.com/meshtastic/st7796/archive/1.0.5.zip
+  # renovate: datasource=custom.pio depName=lewisxhe-SensorLib packageName=lewisxhe/library/SensorLib
+  lewisxhe/SensorLib@0.3.1

variants/esp32/wiphone/platformio.ini

@@ -10,6 +10,9 @@ build_flags =
   -I variants/esp32/wiphone
 lib_deps = 
   ${esp32_base.lib_deps}
-  lovyan03/LovyanGFX@^1.2.0
-  sparkfun/SX1509 IO Expander@^3.0.5
-  pololu/APA102@^3.0.0
+  # renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
+  lovyan03/LovyanGFX@1.2.7
+  # renovate: datasource=custom.pio depName=SX1509 IO Expander packageName=sparkfun/library/SX1509 IO Expander
+  sparkfun/SX1509 IO Expander@3.0.6
+  # renovate: datasource=custom.pio depName=APA102 packageName=pololu/library/APA102
+  pololu/APA102@3.0.0

variants/esp32c3/diy/esp32c3_super_mini/platformio.ini

@@ -4,7 +4,7 @@
 extends = esp32c3_base
 board = esp32-c3-devkitm-1
 build_flags =
-  ${esp32_base.build_flags}
+  ${esp32c3_base.build_flags}
   -D PRIVATE_HW
   -I variants/esp32c3/diy/esp32c3_super_mini
   -D ARDUINO_USB_MODE=1

variants/esp32c3/esp32c3.ini

@@ -4,8 +4,3 @@ custom_esp32_kind = esp32c3
 
 monitor_speed = 115200
 monitor_filters = esp32_c3_exception_decoder
-
-build_flags =
-	${esp32_base.build_flags}
-	-DCONFIG_BT_NIMBLE_EXT_ADV=1
-	-DCONFIG_BT_NIMBLE_MAX_EXT_ADV_INSTANCES=2

variants/esp32c3/hackerboxes_esp32c3_oled/platformio.ini

@@ -3,7 +3,7 @@ extends = esp32c3_base
 board = esp32-c3-devkitm-1
 board_level = extra
 build_flags = 
-  ${esp32_base.build_flags}
+  ${esp32c3_base.build_flags}
   -D PRIVATE_HW
   -D ARDUINO_USB_MODE=1
   -D ARDUINO_USB_CDC_ON_BOOT=1

variants/esp32c3/heltec_esp32c3/platformio.ini

@@ -3,7 +3,7 @@ extends = esp32c3_base
 board = esp32-c3-devkitm-1
 board_level = pr
 build_flags = 
-  ${esp32_base.build_flags}
+  ${esp32c3_base.build_flags}
   -D HELTEC_HT62
   -I variants/esp32c3/heltec_esp32c3
 monitor_speed = 115200

variants/esp32c3/heltec_hru_3601/platformio.ini

@@ -2,8 +2,9 @@
 extends = esp32c3_base
 board = adafruit_qtpy_esp32c3
 build_flags =
-  ${esp32_base.build_flags}
+  ${esp32c3_base.build_flags}
   -D HELTEC_HRU_3601
   -I variants/esp32c3/heltec_hru_3601
 lib_deps = ${esp32c3_base.lib_deps}
-  adafruit/Adafruit NeoPixel @ ^1.12.0
+  # renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
+  adafruit/Adafruit NeoPixel@1.15.2

variants/esp32c3/m5stack-stamp-c3/platformio.ini

@@ -3,7 +3,7 @@ extends = esp32c3_base
 board = esp32-c3-devkitm-1
 board_level = extra
 build_flags = 
-  ${esp32_base.build_flags}
+  ${esp32c3_base.build_flags}
   -D PRIVATE_HW
   -I variants/esp32c3/m5stack-stamp-c3
 monitor_speed = 115200

variants/esp32c6/m5stack_unitc6l/platformio.ini

@@ -12,8 +12,10 @@ build_unflags =
   -D HAS_WIFI
 lib_deps =
   ${esp32c6_base.lib_deps}
-  adafruit/Adafruit NeoPixel@^1.12.3
-  h2zero/NimBLE-Arduino@^2.3.7
+  # renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
+  adafruit/Adafruit NeoPixel@1.15.2
+  # renovate: datasource=custom.pio depName=NimBLE-Arduino packageName=h2zero/library/NimBLE-Arduino
+  h2zero/NimBLE-Arduino@2.3.7
 build_flags = 
   ${esp32c6_base.build_flags}
   -D M5STACK_UNITC6L
@@ -24,6 +26,7 @@ build_flags =
   -D HAS_BLUETOOTH=1
 	-DCONFIG_BT_NIMBLE_EXT_ADV=1
 	-DCONFIG_BT_NIMBLE_MAX_EXT_ADV_INSTANCES=2
+  -D NIMBLE_TWO
 monitor_speed=115200
 lib_ignore =
   NonBlockingRTTTL

variants/esp32s3/ELECROW-ThinkNode-M5/platformio.ini

@@ -16,6 +16,9 @@ build_flags =
   -DEINK_BACKGROUND_USES_FAST          ; (Optional) Use FAST refresh for both BACKGROUND and RESPONSIVE, until a limit is reached.
 
 lib_deps = ${esp32s3_base.lib_deps}
+  # renovate: datasource=git-refs depName=meshtastic-GxEPD2 packageName=https://github.com/meshtastic/GxEPD2 gitBranch=master
   https://github.com/meshtastic/GxEPD2/archive/1655054ba298e0e29fc2044741940f927f9c2a43.zip
-  lewisxhe/PCF8563_Library@^1.0.1
-  maxpromer/PCA9557-arduino @ ^1.0.0
+  # renovate: datasource=custom.pio depName=PCF8563 packageName=lewisxhe/library/PCF8563_Library
+  lewisxhe/PCF8563_Library@1.0.1
+  # renovate: datasource=custom.pio depName=PCA9557-arduino packageName=maxpromer/library/PCA9557-arduino
+  maxpromer/PCA9557-arduino@1.0.0

variants/esp32s3/bpi_picow_esp32_s3/platformio.ini

@@ -8,9 +8,10 @@ board_level = extra
 upload_protocol = esptool
 ;upload_port = /dev/ttyACM2
 lib_deps =
-  ${esp32_base.lib_deps}
-  caveman99/ESP32 Codec2@^1.0.1
+  ${esp32s3_base.lib_deps}
+  # renovate: datasource=custom.pio depName=caveman99-ESP32_Codec2 packageName=caveman99/library/ESP32 Codec2
+  caveman99/ESP32 Codec2@1.0.1
 build_flags = 
-  ${esp32_base.build_flags}
+  ${esp32s3_base.build_flags}
   -D PRIVATE_HW
   -I variants/esp32s3/bpi_picow_esp32_s3

variants/esp32s3/crowpanel-esp32s3-5-epaper/platformio.ini

@@ -25,6 +25,7 @@ build_flags =
   ;-DEINK_LIMIT_RATE_RESPONSIVE_SEC=1 
 lib_deps =
   ${esp32s3_base.lib_deps}
+  # renovate: datasource=git-refs depName=meshtastic-GxEPD2 packageName=https://github.com/meshtastic/GxEPD2 gitBranch=master
   https://github.com/meshtastic/GxEPD2/archive/33db3fa8ee6fc47d160bdb44f8f127c9a9203a10.zip
 
 [env:crowpanel-esp32s3-4-epaper]
@@ -54,6 +55,7 @@ build_flags =
   ;-DEINK_LIMIT_RATE_RESPONSIVE_SEC=1 
 lib_deps =
   ${esp32s3_base.lib_deps}
+  # renovate: datasource=git-refs depName=meshtastic-GxEPD2 packageName=https://github.com/meshtastic/GxEPD2 gitBranch=master
   https://github.com/meshtastic/GxEPD2/archive/33db3fa8ee6fc47d160bdb44f8f127c9a9203a10.zip
 
 [env:crowpanel-esp32s3-2-epaper]
@@ -83,4 +85,5 @@ build_flags =
   ;-DEINK_LIMIT_RATE_RESPONSIVE_SEC=1 
 lib_deps =
   ${esp32s3_base.lib_deps}
+  # renovate: datasource=git-refs depName=meshtastic-GxEPD2 packageName=https://github.com/meshtastic/GxEPD2 gitBranch=master
   https://github.com/meshtastic/GxEPD2/archive/33db3fa8ee6fc47d160bdb44f8f127c9a9203a10.zip

variants/esp32s3/diy/my_esp32s3_diy_eink/platformio.ini

@@ -9,14 +9,16 @@ upload_protocol = esptool
 ;upload_port = /dev/ttyACM1
 upload_speed = 921600
 lib_deps =
-  ${esp32_base.lib_deps}
-  zinggjm/GxEPD2@^1.6.2
-  adafruit/Adafruit NeoPixel @ ^1.12.0
+  ${esp32s3_base.lib_deps}
+  # renovate: datasource=custom.pio depName=GxEPD2 packageName=zinggjm/library/GxEPD2
+  zinggjm/GxEPD2@1.6.5
+  # renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
+  adafruit/Adafruit NeoPixel@1.15.2
 build_unflags =
   ${esp32s3_base.build_unflags}
   -DARDUINO_USB_MODE=1
 build_flags = 
-  ${esp32_base.build_flags}
+  ${esp32s3_base.build_flags}
   -D PRIVATE_HW
   -I variants/esp32s3/diy/my_esp32s3_diy_eink
   -Dmy

variants/esp32s3/diy/my_esp32s3_diy_oled/platformio.ini

@@ -9,13 +9,14 @@ upload_protocol = esptool
 ;upload_port = /dev/ttyACM0
 upload_speed = 921600
 lib_deps =
-  ${esp32_base.lib_deps}
-  adafruit/Adafruit NeoPixel @ ^1.12.0
+  ${esp32s3_base.lib_deps}
+  # renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
+  adafruit/Adafruit NeoPixel@1.15.2
 build_unflags =
   ${esp32s3_base.build_unflags}
   -DARDUINO_USB_MODE=1
 build_flags = 
-  ${esp32_base.build_flags}
+  ${esp32s3_base.build_flags}
   -D PRIVATE_HW
   -I variants/esp32s3/diy/my_esp32s3_diy_oled
   -DBOARD_HAS_PSRAM

variants/esp32s3/dreamcatcher/platformio.ini

@@ -12,8 +12,10 @@ build_flags =
   -D ARDUINO_USB_CDC_ON_BOOT=1
 
 lib_deps = ${esp32s3_base.lib_deps}
-  earlephilhower/ESP8266Audio@^1.9.9
-  earlephilhower/ESP8266SAM@^1.0.1
+  # renovate: datasource=custom.pio depName=ESP8266Audio packageName=earlephilhower/library/ESP8266Audio
+  earlephilhower/ESP8266Audio@1.9.9
+  # renovate: datasource=custom.pio depName=ESP8266SAM packageName=earlephilhower/library/ESP8266SAM
+  earlephilhower/ESP8266SAM@1.1.0
 
 [env:dreamcatcher-2206] 
 extends = esp32s3_base

variants/esp32s3/elecrow_panel/platformio.ini

@@ -41,9 +41,13 @@ build_flags = ${esp32s3_base.build_flags} -Os
 
 lib_deps = ${esp32s3_base.lib_deps}
   ${device-ui_base.lib_deps}
+  # renovate: datasource=custom.pio depName=ESP8266Audio packageName=earlephilhower/library/ESP8266Audio
   earlephilhower/ESP8266Audio@1.9.9
+  # renovate: datasource=custom.pio depName=ESP8266SAM packageName=earlephilhower/library/ESP8266SAM
   earlephilhower/ESP8266SAM@1.0.1
+  # renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
   lovyan03/LovyanGFX@1.2.0 ; note: v1.2.7 breaks the elecrow 7" display functionality
+  # renovate: datasource=custom.pio depName=TCA9534 packageName=hideakitai/library/TCA9534
   hideakitai/TCA9534@0.1.1
 
 [crowpanel_small_esp32s3_base] ; 2.4, 2.8, 3.5 inch

variants/esp32s3/esp32-s3-pico/platformio.ini

@@ -22,5 +22,7 @@ build_flags = ${esp32s3_base.build_flags}
   -DEINK_HEIGHT=128
 
 lib_deps = ${esp32s3_base.lib_deps}
-  zinggjm/GxEPD2@^1.6.2
-  adafruit/Adafruit NeoPixel @ ^1.12.0
+  # renovate: datasource=custom.pio depName=GxEPD2 packageName=zinggjm/library/GxEPD2
+  zinggjm/GxEPD2@1.6.5
+  # renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
+  adafruit/Adafruit NeoPixel@1.15.2

variants/esp32s3/esp32s3.ini

@@ -3,8 +3,3 @@ extends = esp32_base
 custom_esp32_kind = esp32s3
 
 monitor_speed = 115200
-
-build_flags =
-	${esp32_base.build_flags}
-	-DCONFIG_BT_NIMBLE_EXT_ADV=1
-	-DCONFIG_BT_NIMBLE_MAX_EXT_ADV_INSTANCES=2

variants/esp32s3/hackaday-communicator/platformio.ini

@@ -12,4 +12,5 @@ build_flags = ${esp32s3_base.build_flags}
   -I variants/esp32s3/hackaday-communicator
 
 lib_deps = ${esp32s3_base.lib_deps}
-  https://github.com/meshtastic/Arduino_GFX/archive/054e81ffaf23784830a734e3c184346789349406.zip
+  # renovate: datasource=git-refs depName=meshtastic-Arduino_GFX packageName=https://github.com/meshtastic/Arduino_GFX gitBranch=master
+  https://github.com/meshtastic/Arduino_GFX/archive/054e81ffaf23784830a734e3c184346789349406.zip

variants/esp32s3/heltec_sensor_hub/platformio.ini

@@ -9,4 +9,5 @@ build_flags =
   -D HELTEC_SENSOR_HUB
 
 lib_deps = ${esp32s3_base.lib_deps}
-  adafruit/Adafruit NeoPixel @ ^1.12.0
+  # renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
+  adafruit/Adafruit NeoPixel@1.15.2

variants/esp32s3/heltec_v4/platformio.ini

@@ -7,8 +7,6 @@ build_flags =
   ${esp32s3_base.build_flags}
   -D HELTEC_V4
   -I variants/esp32s3/heltec_v4
-lib_deps = 
-  ${esp32s3_base.lib_deps}
 
 
 [env:heltec-v4]
@@ -23,8 +21,6 @@ build_flags =
   -D I2C_SCL=18
   -D I2C_SDA1=4
   -D I2C_SCL1=3
-lib_deps = 
-  ${heltec_v4_base.lib_deps}
 
 [env:heltec-v4-tft]
 extends = heltec_v4_base
@@ -107,6 +103,10 @@ build_flags =
 
 lib_deps = ${heltec_v4_base.lib_deps}
   ; ${device-ui_base.lib_deps}
+  # renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
   lovyan03/LovyanGFX@1.2.0
+  # renovate: datasource=git-refs depName=Quency-D_chsc6x packageName=https://github.com/Quency-D/chsc6x gitBranch=master
   https://github.com/Quency-D/chsc6x/archive/5cbead829d6b432a8d621ed1aafd4eb474fd4f27.zip
+  ; TODO revert to official device-ui (when merged)
+  # renovate: datasource=git-refs depName=Quency-D_device-ui packageName=https://github.com/Quency-D/device-ui gitBranch=heltec-v4-tft
   https://github.com/Quency-D/device-ui/archive/7c9870b8016641190b059bdd90fe16c1012a39eb.zip

variants/esp32s3/heltec_vision_master_e213/platformio.ini

@@ -17,8 +17,10 @@ build_flags =
   -DEINK_HASQUIRK_GHOSTING             ; Display model is identified as "prone to ghosting"
 lib_deps =
   ${esp32s3_base.lib_deps}
+  # renovate: datasource=git-refs depName=meshtastic-GxEPD2 packageName=https://github.com/meshtastic/GxEPD2 gitBranch=master
   https://github.com/meshtastic/GxEPD2/archive/1655054ba298e0e29fc2044741940f927f9c2a43.zip
-  lewisxhe/PCF8563_Library@^1.0.1
+  # renovate: datasource=custom.pio depName=PCF8563 packageName=lewisxhe/library/PCF8563_Library
+  lewisxhe/PCF8563_Library@1.0.1
 upload_speed = 115200
 
 [env:heltec-vision-master-e213-inkhud]
@@ -27,7 +29,7 @@ board = heltec_vision_master_e213
 board_level = pr
 board_build.partitions = default_8MB.csv
 build_src_filter =
-  ${esp32_base.build_src_filter}
+  ${esp32s3_base.build_src_filter}
   ${inkhud.build_src_filter}
 build_flags =  
   ${esp32s3_base.build_flags}

variants/esp32s3/heltec_vision_master_e290/platformio.ini

@@ -20,8 +20,10 @@ build_flags =
 
 lib_deps =
   ${esp32s3_base.lib_deps}
+  # renovate: datasource=git-refs depName=meshtastic-GxEPD2 packageName=https://github.com/meshtastic/GxEPD2 gitBranch=master
   https://github.com/meshtastic/GxEPD2/archive/448c8538129fde3d02a7cb5e6fc81971ad92547f.zip
-  lewisxhe/PCF8563_Library@^1.0.1
+  # renovate: datasource=custom.pio depName=PCF8563 packageName=lewisxhe/library/PCF8563_Library
+  lewisxhe/PCF8563_Library@1.0.1
 upload_speed = 115200
 
 [env:heltec-vision-master-e290-inkhud]
@@ -29,7 +31,7 @@ extends = esp32s3_base, inkhud
 board = heltec_vision_master_e290
 board_build.partitions = default_8MB.csv
 build_src_filter = 
-  ${esp32_base.build_src_filter} 
+  ${esp32s3_base.build_src_filter}
   ${inkhud.build_src_filter}
 build_flags = 
   ${esp32s3_base.build_flags}

variants/esp32s3/heltec_vision_master_t190/platformio.ini

@@ -8,6 +8,8 @@ build_flags =
   -D HELTEC_VISION_MASTER_T190
 lib_deps =
   ${esp32s3_base.lib_deps}
-  lewisxhe/PCF8563_Library@^1.0.1
+  # renovate: datasource=custom.pio depName=PCF8563 packageName=lewisxhe/library/PCF8563_Library
+  lewisxhe/PCF8563_Library@1.0.1
+  # renovate: datasource=git-refs depName=meshtastic-st7789 packageName=https://github.com/meshtastic/st7789 gitBranch=main
   https://github.com/meshtastic/st7789/archive/bd33ea58ddfe4a5e4a66d53300ccbd38d66ac21f.zip
 upload_speed = 921600

variants/esp32s3/heltec_wireless_paper/platformio.ini

@@ -18,8 +18,10 @@ build_flags =
   -D EINK_HASQUIRK_GHOSTING             ; Display model is identified as "prone to ghosting"
 lib_deps =
   ${esp32s3_base.lib_deps}
+  # renovate: datasource=git-refs depName=meshtastic-GxEPD2 packageName=https://github.com/meshtastic/GxEPD2 gitBranch=master
   https://github.com/meshtastic/GxEPD2/archive/1655054ba298e0e29fc2044741940f927f9c2a43.zip
-  lewisxhe/PCF8563_Library@^1.0.1
+  # renovate: datasource=custom.pio depName=PCF8563 packageName=lewisxhe/library/PCF8563_Library
+  lewisxhe/PCF8563_Library@1.0.1
 upload_speed = 115200
 
 [env:heltec-wireless-paper-inkhud]
@@ -27,7 +29,7 @@ extends = esp32s3_base, inkhud
 board = heltec_wifi_lora_32_V3
 board_build.partitions = default_8MB.csv
 build_src_filter =
-  ${esp32_base.build_src_filter} 
+  ${esp32s3_base.build_src_filter}
   ${inkhud.build_src_filter}
 build_flags =
   ${esp32s3_base.build_flags}

variants/esp32s3/heltec_wireless_paper_v1/platformio.ini

@@ -15,6 +15,8 @@ build_flags =
   -D EINK_LIMIT_GHOSTING_PX=2000        ; (Optional) How much image ghosting is tolerated
 lib_deps =
   ${esp32s3_base.lib_deps}
+  # renovate: datasource=git-refs depName=meshtastic-GxEPD2 packageName=https://github.com/meshtastic/GxEPD2 gitBranch=master
   https://github.com/meshtastic/GxEPD2/archive/55f618961db45a23eff0233546430f1e5a80f63a.zip
-  lewisxhe/PCF8563_Library@^1.0.1
+  # renovate: datasource=custom.pio depName=PCF8563 packageName=lewisxhe/library/PCF8563_Library
+  lewisxhe/PCF8563_Library@1.0.1
 upload_speed = 115200

variants/esp32s3/heltec_wireless_tracker/platformio.ini

@@ -12,4 +12,5 @@ build_flags =
 
 lib_deps =
   ${esp32s3_base.lib_deps}
-  lovyan03/LovyanGFX@^1.2.0
+  # renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
+  lovyan03/LovyanGFX@1.2.7

variants/esp32s3/heltec_wireless_tracker_V1_0/platformio.ini

@@ -11,4 +11,5 @@ build_flags =
   ;-D DEBUG_DISABLED ; uncomment this line to disable DEBUG output
 lib_deps =
   ${esp32s3_base.lib_deps}
-  lovyan03/LovyanGFX@^1.2.0
+  # renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
+  lovyan03/LovyanGFX@1.2.7

variants/esp32s3/heltec_wireless_tracker_v2/platformio.ini

@@ -10,4 +10,5 @@ build_flags =
   -D HELTEC_WIRELESS_TRACKER_V2
 lib_deps =
   ${esp32s3_base.lib_deps}
-  lovyan03/LovyanGFX@^1.2.0
+  # renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
+  lovyan03/LovyanGFX@1.2.7

variants/esp32s3/icarus/platformio.ini

@@ -7,9 +7,8 @@ board_build.mcu = esp32s3
 board_build.partitions = default_8MB.csv
 upload_protocol = esptool
 upload_speed = 921600
+; TODO renovate or remove
 platform_packages = platformio/framework-arduinoespressif32@https://github.com/PowerFeather/powerfeather-meshtastic-arduino-lib/releases/download/2.0.16a/esp32-2.0.16.zip
-lib_deps =
-  ${esp32s3_base.lib_deps}
 build_unflags =
   ${esp32s3_base.build_unflags}
   -DARDUINO_USB_MODE=1

variants/esp32s3/link32_s3_v1/platformio.ini

@@ -3,7 +3,7 @@ extends = esp32s3_base
 board = esp32-s3-devkitc-1
 board_level = extra
 build_flags = 
-  ${esp32_base.build_flags}
+  ${esp32s3_base.build_flags}
   -D LINK_32
   -I variants/esp32s3/link32_s3_v1
   -DARDUINO_USB_CDC_ON_BOOT

variants/esp32s3/m5stack_cores3/platformio.ini

@@ -6,8 +6,7 @@ board_check = true
 board_build.partitions = default_16MB.csv
 upload_protocol = esptool
 build_flags = 
-  ${esp32_base.build_flags} 
+  ${esp32s3_base.build_flags}
   -D PRIVATE_HW
   -D M5STACK_CORES3
   -I variants/esp32s3/m5stack_cores3
-lib_deps = ${esp32_base.lib_deps}

variants/esp32s3/mesh-tab/platformio.ini

@@ -46,11 +46,12 @@ build_flags = ${esp32s3_base.build_flags}
   -D VIEW_320x240
   -D USE_PACKET_API
   -I variants/esp32s3/mesh-tab
-build_src_filter = ${esp32_base.build_src_filter}
+build_src_filter = ${esp32s3_base.build_src_filter}
 lib_deps =
-  ${esp32_base.lib_deps}
+  ${esp32s3_base.lib_deps}
   ${device-ui_base.lib_deps}
-  lovyan03/LovyanGFX@^1.2.0
+  # renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
+  lovyan03/LovyanGFX@1.2.7
 
 [mesh_tab_xpt2046]
 extends = mesh_tab_base

variants/esp32s3/nibble_esp32/platformio.ini

@@ -3,6 +3,6 @@ extends = esp32s3_base
 board = esp32-s3-zero
 board_level = extra
 build_flags = 
-  ${esp32_base.build_flags}
+  ${esp32s3_base.build_flags}
   -D PRIVATE_HW
   -I variants/esp32s3/nibble_esp32

variants/esp32s3/picomputer-s3/platformio.ini

@@ -15,7 +15,8 @@ build_flags =
 
 lib_deps = 
   ${esp32s3_base.lib_deps}
-  lovyan03/LovyanGFX@^1.2.0
+  # renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
+  lovyan03/LovyanGFX@1.2.7
 
 build_src_filter =
   ${esp32s3_base.build_src_filter}

variants/esp32s3/rak3312/platformio.ini

@@ -6,6 +6,6 @@ board_check = true
 upload_protocol = esptool
 
 build_flags = 
-  ${esp32_base.build_flags}
+  ${esp32s3_base.build_flags}
   -D RAK3312
   -I variants/esp32s3/rak3312

variants/esp32s3/rak_wismesh_tap_v2/platformio.ini

@@ -8,14 +8,15 @@ upload_protocol = esptool
 board_build.partitions = default_8MB.csv
 
 build_flags = 
-  ${esp32_base.build_flags} 
+  ${esp32s3_base.build_flags}
   -D RAK3312
   -D RAK_WISMESH_TAP_V2 
   -I variants/esp32s3/rak_wismesh_tap_v2
 
 lib_deps =
   ${esp32s3_base.lib_deps}
-  lovyan03/LovyanGFX@^1.2.0
+  # renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
+  lovyan03/LovyanGFX@1.2.7
 
 [ft5x06]
 extends = mesh_tab_base

variants/esp32s3/seeed-sensecap-indicator/platformio.ini

@@ -9,7 +9,7 @@ board_check = true
 board_build.partitions = partition-table-8MB.csv
 upload_protocol = esptool
 
-build_flags = ${esp32_base.build_flags}
+build_flags = ${esp32s3_base.build_flags}
   -Ivariants/esp32s3/seeed-sensecap-indicator
   -DSENSECAP_INDICATOR
   -DCONFIG_ARDUHAL_LOG_COLORS
@@ -24,10 +24,12 @@ build_flags = ${esp32_base.build_flags}
   -DUSE_ARDUINO_HAL_GPIO
 
 lib_deps = ${esp32s3_base.lib_deps}
+  ; TODO switch back to official LovyanGFX
   https://github.com/mverch67/LovyanGFX/archive/4c76238c1344162a234ae917b27651af146d6fb2.zip
-  earlephilhower/ESP8266Audio@^1.9.9
-  earlephilhower/ESP8266SAM@^1.0.1
-
+  # renovate: datasource=custom.pio depName=ESP8266Audio packageName=earlephilhower/library/ESP8266Audio
+  earlephilhower/ESP8266Audio@1.9.9
+  # renovate: datasource=custom.pio depName=ESP8266SAM packageName=earlephilhower/library/ESP8266SAM
+  earlephilhower/ESP8266SAM@1.1.0
 
 [env:seeed-sensecap-indicator-tft]
 extends = env:seeed-sensecap-indicator
@@ -64,4 +66,5 @@ build_flags =
 lib_deps =
   ${env:seeed-sensecap-indicator.lib_deps}
   ${device-ui_base.lib_deps}
+  ; TODO switch back to official bb_captouch
   https://github.com/mverch67/bb_captouch/archive/8626412fe650d808a267791c0eae6e5860c85a5d.zip ; alternative touch library supporting FT6x36

variants/esp32s3/seeed_xiao_s3/platformio.ini

@@ -6,8 +6,6 @@ board_check = true
 board_build.partitions = default_8MB.csv
 upload_protocol = esptool
 upload_speed = 921600
-lib_deps =
-  ${esp32s3_base.lib_deps}
 build_unflags =
   ${esp32s3_base.build_unflags}
   -DARDUINO_USB_MODE=1

variants/esp32s3/station-g2/platformio.ini

@@ -8,8 +8,6 @@ board_build.mcu = esp32s3
 upload_protocol = esptool
 ;upload_port = /dev/ttyACM0
 upload_speed = 921600
-lib_deps =
-  ${esp32s3_base.lib_deps}
 build_unflags =
   ${esp32s3_base.build_unflags}
   -DARDUINO_USB_MODE=1

variants/esp32s3/t-deck-pro/platformio.ini

@@ -5,7 +5,7 @@ board_check = true
 upload_protocol = esptool
 
 build_flags = 
-  ${esp32_base.build_flags} -I variants/esp32s3/t-deck-pro
+  ${esp32s3_base.build_flags} -I variants/esp32s3/t-deck-pro
   -D T_DECK_PRO
   -D USE_EINK
   -D EINK_DISPLAY_MODEL=GxEPD2_310_GDEQ031T10
@@ -17,7 +17,11 @@ build_flags =
 
 lib_deps =
   ${esp32s3_base.lib_deps}
-  https://github.com/ZinggJM/GxEPD2/archive/refs/tags/1.6.4.zip
+  # renovate: datasource=custom.pio depName=GxEPD2 packageName=zinggjm/library/GxEPD2
+  zinggjm/GxEPD2@1.6.4
+  # renovate: datasource=git-refs depName=CSE_Touch packageName=https://github.com/CIRCUITSTATE/CSE_Touch gitBranch=main
   https://github.com/CIRCUITSTATE/CSE_Touch/archive/b44f23b6f870b848f1fbe453c190879bc6cfaafa.zip
+  # renovate: datasource=github-tags depName=CSE_CST328 packageName=CIRCUITSTATE/CSE_CST328
   https://github.com/CIRCUITSTATE/CSE_CST328/archive/refs/tags/v0.0.4.zip
+  # renovate: datasource=git-refs depName=BQ27220 packageName=https://github.com/mverch67/BQ27220 gitBranch=main
   https://github.com/mverch67/BQ27220/archive/07d92be846abd8a0258a50c23198dac0858b22ed.zip

variants/esp32s3/t-deck/platformio.ini

@@ -12,9 +12,12 @@ build_flags = ${esp32s3_base.build_flags}
   -I variants/esp32s3/t-deck
 
 lib_deps = ${esp32s3_base.lib_deps}
-	lovyan03/LovyanGFX@^1.2.0
-  earlephilhower/ESP8266Audio@^1.9.9
-  earlephilhower/ESP8266SAM@^1.0.1
+  # renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
+  lovyan03/LovyanGFX@1.2.7
+  # renovate: datasource=custom.pio depName=ESP8266Audio packageName=earlephilhower/library/ESP8266Audio
+  earlephilhower/ESP8266Audio@1.9.9
+  # renovate: datasource=custom.pio depName=ESP8266SAM packageName=earlephilhower/library/ESP8266SAM
+  earlephilhower/ESP8266SAM@1.1.0
 
 [env:t-deck-tft]
 extends = env:t-deck
@@ -68,4 +71,5 @@ build_flags =
 lib_deps =
   ${env:t-deck.lib_deps}
   ${device-ui_base.lib_deps}
+  # renovate: datasource=github-tags depName=bb_captouch packageName=bitbank2/bb_captouch
   https://github.com/bitbank2/bb_captouch/archive/refs/tags/1.3.1.zip

variants/esp32s3/t-eth-elite/platformio.ini

@@ -15,4 +15,5 @@ lib_ignore =
 
 lib_deps = 
   ${esp32s3_base.lib_deps}
+  # renovate: datasource=github-tags depName=ETHClass2 packageName=meshtastic/ETHClass2
   https://github.com/meshtastic/ETHClass2/archive/v1.0.0.zip

variants/esp32s3/t-watch-s3/platformio.ini

@@ -6,16 +6,22 @@ board_check = true
 board_build.partitions = default_16MB.csv
 upload_protocol = esptool
 
-build_flags = ${esp32_base.build_flags} 
+build_flags = ${esp32s3_base.build_flags}
   -DT_WATCH_S3
   -Ivariants/esp32s3/t-watch-s3
   -DPCF8563_RTC=0x51
   -DHAS_BMA423=1
 
 lib_deps = ${esp32s3_base.lib_deps}
-	lovyan03/LovyanGFX@^1.2.0
+  # renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
+  lovyan03/LovyanGFX@1.2.7
+  # renovate: datasource=custom.pio depName=PCF8563 packageName=lewisxhe/library/PCF8563_Library
   lewisxhe/PCF8563_Library@1.0.1
-  adafruit/Adafruit DRV2605 Library@^1.2.2
-  earlephilhower/ESP8266Audio@^1.9.9
-  earlephilhower/ESP8266SAM@^1.0.1
+  # renovate: datasource=custom.pio depName=Adafruit DRV2605 packageName=adafruit/library/Adafruit DRV2605 Library
+  adafruit/Adafruit DRV2605 Library@1.2.4
+  # renovate: datasource=custom.pio depName=ESP8266Audio packageName=earlephilhower/library/ESP8266Audio
+  earlephilhower/ESP8266Audio@1.9.9
+  # renovate: datasource=custom.pio depName=ESP8266SAM packageName=earlephilhower/library/ESP8266SAM
+  earlephilhower/ESP8266SAM@1.1.0
+  # renovate: datasource=custom.pio depName=lewisxhe-SensorLib packageName=lewisxhe/library/SensorLib
   lewisxhe/SensorLib@0.2.0

variants/esp32s3/tbeam-s3-core/platformio.ini

@@ -7,6 +7,7 @@ board_check = true
 
 lib_deps =
   ${esp32s3_base.lib_deps}
+  # renovate: datasource=custom.pio depName=PCF8563 packageName=lewisxhe/library/PCF8563_Library
   lewisxhe/PCF8563_Library@1.0.1
 
 build_flags = 

variants/esp32s3/tlora-pager/platformio.ini

@@ -17,14 +17,23 @@ build_flags = ${esp32s3_base.build_flags}
   -D ROTARY_BUXTRONICS
 
 lib_deps = ${esp32s3_base.lib_deps}
+  # renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
   lovyan03/LovyanGFX@1.2.7
+  # renovate: datasource=custom.pio depName=ESP8266Audio packageName=earlephilhower/library/ESP8266Audio
   earlephilhower/ESP8266Audio@1.9.9
+  # renovate: datasource=custom.pio depName=ESP8266SAM packageName=earlephilhower/library/ESP8266SAM
   earlephilhower/ESP8266SAM@1.0.1
+  # renovate: datasource=custom.pio depName=Adafruit DRV2605 packageName=adafruit/library/Adafruit DRV2605 Library
   adafruit/Adafruit DRV2605 Library@1.2.4
+  # renovate: datasource=custom.pio depName=PCF8563 packageName=lewisxhe/library/PCF8563_Library
   lewisxhe/PCF8563_Library@1.0.1
+  # renovate: datasource=custom.pio depName=lewisxhe-SensorLib packageName=lewisxhe/library/SensorLib
   lewisxhe/SensorLib@0.3.1
-  https://github.com/pschatzmann/arduino-audio-driver/archive/refs/tags/v0.1.3.zip
+  # renovate: datasource=github-tags depName=pschatzmann_arduino-audio-driver packageName=pschatzmann/arduino-audio-driver
+  https://github.com/pschatzmann/arduino-audio-driver/archive/v0.1.3.zip
+  # TODO renovate
   https://github.com/mverch67/BQ27220/archive/07d92be846abd8a0258a50c23198dac0858b22ed.zip
+  # TODO renovate
   https://github.com/mverch67/RotaryEncoder/archive/da958a21389cbcd485989705df602a33e092dd88.zip
 
 [env:tlora-pager-tft]

variants/esp32s3/tlora_t3s3_epaper/platformio.ini

@@ -5,7 +5,7 @@ board_check = true
 upload_protocol = esptool
 
 build_flags = 
-  ${esp32_base.build_flags}
+  ${esp32s3_base.build_flags}
   -D TLORA_T3S3_EPAPER
   -I variants/esp32s3/tlora_t3s3_epaper
   -DUSE_EINK
@@ -20,6 +20,7 @@ build_flags =
 
 lib_deps =
   ${esp32s3_base.lib_deps}
+  # renovate: datasource=git-refs depName=meshtastic-GxEPD2 packageName=https://github.com/meshtastic/GxEPD2 gitBranch=master
   https://github.com/meshtastic/GxEPD2/archive/b202ebfec6a4821e098cf7a625ba0f6f2400292d.zip
 
 [env:tlora-t3s3-epaper-inkhud]
@@ -28,7 +29,7 @@ board = tlora-t3s3-v1
 board_check = true
 upload_protocol = esptool
 build_src_filter =
-  ${esp32_base.build_src_filter}
+  ${esp32s3_base.build_src_filter}
   ${inkhud.build_src_filter}
 build_flags =
   ${esp32s3_base.build_flags}

variants/esp32s3/tlora_t3s3_v1/platformio.ini

@@ -5,4 +5,6 @@ board_check = true
 upload_protocol = esptool
 
 build_flags = 
-  ${esp32_base.build_flags} -D TLORA_T3S3_V1 -I variants/esp32s3/tlora_t3s3_v1
+  ${esp32s3_base.build_flags}
+  -D TLORA_T3S3_V1
+  -I variants/esp32s3/tlora_t3s3_v1

variants/esp32s3/tracksenger/platformio.ini

@@ -12,7 +12,8 @@ build_flags =
 
 lib_deps =
   ${esp32s3_base.lib_deps}
-  lovyan03/LovyanGFX@^1.2.0
+  # renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
+  lovyan03/LovyanGFX@1.2.7
 
 [env:tracksenger-lcd]
 extends = esp32s3_base
@@ -28,7 +29,8 @@ build_flags =
 
 lib_deps =
   ${esp32s3_base.lib_deps}
-  lovyan03/LovyanGFX@^1.2.0
+  # renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
+  lovyan03/LovyanGFX@1.2.7
 
 [env:tracksenger-oled]
 extends = esp32s3_base

variants/esp32s3/unphone/platformio.ini

@@ -27,10 +27,12 @@ build_src_filter =
   +<../variants/esp32s3/unphone>
 
 lib_deps = ${esp32s3_base.lib_deps}
-  lovyan03/LovyanGFX@ 1.2.0
+  # renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
+  lovyan03/LovyanGFX@1.2.0
+  # TODO renovate
   https://gitlab.com/hamishcunningham/unphonelibrary#meshtastic@9.0.0
-  adafruit/Adafruit NeoPixel @ ^1.12.0
-
+  # renovate: datasource=custom.pio depName=NeoPixel packageName=adafruit/library/Adafruit NeoPixel
+  adafruit/Adafruit NeoPixel@1.15.2
 
 [env:unphone-tft]
 board_level = extra

variants/native/portduino-buildroot/platformio.ini

@@ -5,5 +5,4 @@ extends = portduino_base
 build_flags = ${portduino_base.build_flags} -O0 -I variants/native/portduino-buildroot
 board = buildroot
 board_level = extra
-lib_deps = ${portduino_base.lib_deps}
 build_src_filter = ${portduino_base.build_src_filter}

variants/native/portduino.ini

@@ -21,12 +21,13 @@ build_src_filter =
 lib_deps =
   ${env.lib_deps}
   ${networking_base.lib_deps}
+  ${networking_extra.lib_deps}
   ${radiolib_base.lib_deps}
   ${environmental_base.lib_deps}
   # renovate: datasource=custom.pio depName=rweather/Crypto packageName=rweather/library/Crypto
   rweather/Crypto@0.4.0
   # renovate: datasource=custom.pio depName=LovyanGFX packageName=lovyan03/library/LovyanGFX
-  lovyan03/LovyanGFX@^1.2.0
+  lovyan03/LovyanGFX@1.2.7
   # renovate: datasource=git-refs depName=libch341-spi-userspace packageName=https://github.com/pine64/libch341-spi-userspace gitBranch=main
   https://github.com/pine64/libch341-spi-userspace/archive/af9bc27c9c30fa90772279925b7c5913dff789b4.zip
   # renovate: datasource=custom.pio depName=adafruit/Adafruit seesaw Library packageName=adafruit/library/Adafruit seesaw Library

variants/native/portduino/platformio.ini

@@ -6,7 +6,8 @@ board = cross_platform
 board_level = extra
 lib_deps = 
   ${portduino_base.lib_deps}
-  melopero/Melopero RV3028@^1.1.0
+  # renovate: datasource=custom.pio depName=Melopero RV3028 packageName=melopero/library/Melopero RV3028
+  melopero/Melopero RV3028@1.2.0
 
 build_src_filter = ${portduino_base.build_src_filter}
 

variants/nrf52840/Dongle_nRF52840-pca10059-v1/platformio.ini

@@ -11,5 +11,6 @@ build_flags = ${nrf52840_base.build_flags}
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/Dongle_nRF52840-pca10059-v1>
 lib_deps = 
   ${nrf52840_base.lib_deps}
-  zinggjm/GxEPD2@^1.6.2
+  # renovate: datasource=custom.pio depName=GxEPD2 packageName=zinggjm/library/GxEPD2
+  zinggjm/GxEPD2@1.6.5
 debug_tool = jlink

variants/nrf52840/ELECROW-ThinkNode-M1/platformio.ini

@@ -23,9 +23,12 @@ build_flags = ${nrf52840_base.build_flags}
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/ELECROW-ThinkNode-M1>
 lib_deps = 
   ${nrf52840_base.lib_deps}
+  # renovate: datasource=git-refs depName=meshtastic-GxEPD2 packageName=https://github.com/meshtastic/GxEPD2 gitBranch=master
   https://github.com/meshtastic/GxEPD2/archive/33db3fa8ee6fc47d160bdb44f8f127c9a9203a10.zip
-  lewisxhe/PCF8563_Library@^1.0.1
-  khoih-prog/nRF52_PWM@^1.0.1
+  # renovate: datasource=custom.pio depName=PCF8563 packageName=lewisxhe/library/PCF8563_Library
+  lewisxhe/PCF8563_Library@1.0.1
+  # renovate: datasource=custom.pio depName=nRF52_PWM packageName=khoih-prog/library/nRF52_PWM
+  khoih-prog/nRF52_PWM@1.0.1
 ;upload_protocol = fs
 
 [env:thinknode_m1-inkhud]
@@ -45,4 +48,5 @@ build_src_filter =
 lib_deps = 
   ${inkhud.lib_deps} ; InkHUD libs first, so we get GFXRoot instead of AdafruitGFX
   ${nrf52840_base.lib_deps}
-  lewisxhe/PCF8563_Library@^1.0.1
+  # renovate: datasource=custom.pio depName=PCF8563 packageName=lewisxhe/library/PCF8563_Library
+  lewisxhe/PCF8563_Library@1.0.1

variants/nrf52840/ELECROW-ThinkNode-M3/platformio.ini

@@ -13,5 +13,7 @@ build_flags =
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/ELECROW-ThinkNode-M3>
 lib_deps = 
   ${nrf52840_base.lib_deps}
-  khoih-prog/nRF52_PWM@^1.0.1
-  lewisxhe/PCF8563_Library@^1.0.1
+  # renovate: datasource=custom.pio depName=nRF52_PWM packageName=khoih-prog/library/nRF52_PWM
+  khoih-prog/nRF52_PWM@1.0.1
+  # renovate: datasource=custom.pio depName=PCF8563 packageName=lewisxhe/library/PCF8563_Library
+  lewisxhe/PCF8563_Library@1.0.1

variants/nrf52840/ELECROW-ThinkNode-M3/variant.h

@@ -54,7 +54,6 @@ extern "C" {
 #define LED_POWER red_LED_PIN
 #define LED_CHARGE LED_POWER // Signals the Status LED Module to handle this LED
 #define green_LED_PIN 35
-#define PIN_LED2 green_LED_PIN
 #define LED_BLUE 37
 #define LED_PAIRING LED_BLUE // Signals the Status LED Module to handle this LED
 

variants/nrf52840/ELECROW-ThinkNode-M6/platformio.ini

@@ -12,4 +12,5 @@ build_flags = ${nrf52840_base.build_flags}
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/ELECROW-ThinkNode-M6>
 lib_deps =
   ${nrf52840_base.lib_deps}
-  lewisxhe/PCF8563_Library@^1.0.1
+  # renovate: datasource=custom.pio depName=PCF8563 packageName=lewisxhe/library/PCF8563_Library
+  lewisxhe/PCF8563_Library@1.0.1

variants/nrf52840/ME25LS01-4Y10TD/platformio.ini

@@ -10,8 +10,6 @@ build_flags = ${nrf52840_base.build_flags}
   -DME25LS01_4Y10TD
 board_build.ldscript = src/platform/nrf52/nrf52840_s140_v7.ld
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/ME25LS01-4Y10TD>
-lib_deps = 
-  ${nrf52840_base.lib_deps}
 ; If not set we will default to uploading over serial (first it forces bootloader entry by talking 1200bps to cdcacm)
 upload_protocol = nrfutil
 ;upload_port = /dev/ttyACM1

variants/nrf52840/ME25LS01-4Y10TD_e-ink/platformio.ini

@@ -15,7 +15,8 @@ board_build.ldscript = src/platform/nrf52/nrf52840_s140_v7.ld
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/ME25LS01-4Y10TD_e-ink>
 lib_deps = 
   ${nrf52840_base.lib_deps}
-  zinggjm/GxEPD2@^1.6.2
+  # renovate: datasource=custom.pio depName=GxEPD2 packageName=zinggjm/library/GxEPD2
+  zinggjm/GxEPD2@1.6.5
 ; If not set we will default to uploading over serial (first it forces bootloader entry by talking 1200bps to cdcacm)
 upload_protocol = nrfutil
 ;upload_port = /dev/ttyACM1

variants/nrf52840/MS24SF1/platformio.ini

@@ -9,8 +9,6 @@ build_flags = ${nrf52840_base.build_flags}
   -Isrc/platform/nrf52/softdevice/nrf52
 board_build.ldscript = src/platform/nrf52/nrf52840_s140_v7.ld
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/MS24SF1>
-lib_deps =
-  ${nrf52840_base.lib_deps}
 ; If not set we will default to uploading over serial (first it forces bootloader entry by talking 1200bps to cdcacm)
 upload_protocol = nrfutil
 ;upload_port = /dev/ttyACM1

variants/nrf52840/MakePython_nRF52840_eink/platformio.ini

@@ -12,7 +12,9 @@ build_flags = ${nrf52840_base.build_flags}
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/MakePython_nRF52840_eink>
 lib_deps = 
   ${nrf52840_base.lib_deps}
+  # renovate: datasource=git-refs depName=meshtastic-ESP32_Codec2 packageName=https://github.com/meshtastic/ESP32_Codec2 gitBranch=master
   https://github.com/meshtastic/ESP32_Codec2/archive/633326c78ac251c059ab3a8c430fcdf25b41672f.zip
-  zinggjm/GxEPD2@^1.6.2
+  # renovate: datasource=custom.pio depName=GxEPD2 packageName=zinggjm/library/GxEPD2
+  zinggjm/GxEPD2@1.6.5
 debug_tool = jlink
 ;upload_port = /dev/ttyACM4

variants/nrf52840/MakePython_nRF52840_oled/platformio.ini

@@ -8,5 +8,6 @@ build_flags = ${nrf52840_base.build_flags}
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/MakePython_nRF52840_oled>
 lib_deps = 
   ${nrf52840_base.lib_deps}
+  # renovate: datasource=git-refs depName=meshtastic-ESP32_Codec2 packageName=https://github.com/meshtastic/ESP32_Codec2 gitBranch=master
   https://github.com/meshtastic/ESP32_Codec2/archive/633326c78ac251c059ab3a8c430fcdf25b41672f.zip
 debug_tool = jlink

variants/nrf52840/TWC_mesh_v4/platformio.ini

@@ -8,5 +8,6 @@ build_flags = ${nrf52840_base.build_flags}
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/TWC_mesh_v4>
 lib_deps = 
   ${nrf52840_base.lib_deps}
-  zinggjm/GxEPD2@^1.6.2
+  # renovate: datasource=custom.pio depName=GxEPD2 packageName=zinggjm/library/GxEPD2
+  zinggjm/GxEPD2@1.6.5
 debug_tool = jlink

variants/nrf52840/canaryone/platformio.ini

@@ -11,5 +11,6 @@ build_flags =
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/canaryone>
 lib_deps = 
   ${nrf52840_base.lib_deps}
-  lewisxhe/PCF8563_Library@^1.0.1
+  # renovate: datasource=custom.pio depName=PCF8563 packageName=lewisxhe/library/PCF8563_Library
+  lewisxhe/PCF8563_Library@1.0.1
 ;upload_protocol = fs

variants/nrf52840/diy/WashTastic/platformio.ini

@@ -8,6 +8,4 @@ build_flags = ${nrf52840_base.build_flags}
   -D PRIVATE_HW
   -D EBYTE_E22_900M30S
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/diy/nrf52_promicro_diy_tcxo>
-lib_deps = 
-  ${nrf52840_base.lib_deps}
 debug_tool = jlink

variants/nrf52840/diy/nrf52_promicro_diy_tcxo/platformio.ini

@@ -6,8 +6,6 @@ build_flags = ${nrf52840_base.build_flags}
   -I variants/nrf52840/diy/nrf52_promicro_diy_tcxo
   -D NRF52_PROMICRO_DIY
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/diy/nrf52_promicro_diy_tcxo>
-lib_deps = 
-  ${nrf52840_base.lib_deps}
 debug_tool = jlink
 
 ; NRF52 ProMicro w/ E-Ink display

variants/nrf52840/diy/seeed-xiao-nrf52840-wio-sx1262/platformio.ini

@@ -10,6 +10,4 @@ build_flags = ${nrf52840_base.build_flags}
   -Isrc/platform/nrf52/softdevice/nrf52
 board_build.ldscript = src/platform/nrf52/nrf52840_s140_v7.ld
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/diy/seeed-xiao-nrf52840-wio-sx1262>
-lib_deps =
-  ${nrf52840_base.lib_deps}
 debug_tool = jlink

variants/nrf52840/feather_diy/platformio.ini

@@ -6,8 +6,6 @@ build_flags = ${nrf52840_base.build_flags}
   -Ivariants/nrf52840/feather_diy
   -Dfeather_diy
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/feather_diy>
-lib_deps = 
-  ${nrf52840_base.lib_deps}
 debug_tool = jlink
 ; If not set we will default to uploading over serial (first it forces bootloader entry by talking 1200bps to cdcacm)
 ;upload_protocol = jlink

variants/nrf52840/gat562_mesh_trial_tracker/platformio.ini

@@ -12,5 +12,3 @@ build_flags = ${nrf52840_base.build_flags}
   -DRADIOLIB_EXCLUDE_SX127X=1
   -DRADIOLIB_EXCLUDE_LR11X0=1
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/gat562_mesh_trial_tracker>
-lib_deps =
-  ${nrf52840_base.lib_deps}

variants/nrf52840/heltec_mesh_node_t114-inkhud/platformio.ini

@@ -14,7 +14,8 @@ build_src_filter =
 lib_deps = 
   ${inkhud.lib_deps} ; InkHUD libs first, so we get GFXRoot instead of AdafruitGFX
   ${nrf52840_base.lib_deps}
-  lewisxhe/PCF8563_Library@^1.0.1
+  # renovate: datasource=custom.pio depName=PCF8563 packageName=lewisxhe/library/PCF8563_Library
+  lewisxhe/PCF8563_Library@1.0.1
 extra_scripts =
   ${env.extra_scripts}
   variants/nrf52840/diy/nrf52_promicro_diy_tcxo/custom_build_tasks.py ; Add to PIO's Project Tasks pane: preset builds for common displays

variants/nrf52840/heltec_mesh_node_t114/platformio.ini

@@ -13,5 +13,7 @@ build_flags = ${nrf52840_base.build_flags}
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/heltec_mesh_node_t114>
 lib_deps = 
   ${nrf52840_base.lib_deps}
-  lewisxhe/PCF8563_Library@^1.0.1
-  https://github.com/meshtastic/st7789/archive/bd33ea58ddfe4a5e4a66d53300ccbd38d66ac21f.zip
+  # renovate: datasource=custom.pio depName=PCF8563 packageName=lewisxhe/library/PCF8563_Library
+  lewisxhe/PCF8563_Library@1.0.1
+  # renovate: datasource=git-refs depName=meshtastic-st7789 packageName=https://github.com/meshtastic/st7789 gitBranch=main
+  https://github.com/meshtastic/st7789/archive/bd33ea58ddfe4a5e4a66d53300ccbd38d66ac21f.zip