Increase duration of chirp sound in playChirp

* Fix LNA/PA power control for Heltec v4, wireless tracker v2

* Stop using pin 46 as RF switch, just let DIO2 switch handle the RF path

---------

Co-authored-by: Ben Meadors <benmmeadors@gmail.com>

bin/build-esp32.sh

@@ -38,4 +38,4 @@ cp bin/device-install.* $OUTDIR/
 cp bin/device-update.* $OUTDIR/
 
 echo "Copying manifest"
-cp $BUILDDIR/$basename.mt.json $OUTDIR/$basename.mt.json
+cp $BUILDDIR/$basename.mt.json $OUTDIR/$basename.mt.json || true

bin/build-nrf52.sh

@@ -49,4 +49,4 @@ if (echo $1 | grep -q "rak4631"); then
 fi
 
 echo "Copying manifest"
-cp $BUILDDIR/$basename.mt.json $OUTDIR/$basename.mt.json
+cp $BUILDDIR/$basename.mt.json $OUTDIR/$basename.mt.json || true

bin/build-rp2xx0.sh

@@ -30,4 +30,4 @@ echo "Copying uf2 file"
 cp $BUILDDIR/$basename.uf2 $OUTDIR/$basename.uf2
 
 echo "Copying manifest"
-cp $BUILDDIR/$basename.mt.json $OUTDIR/$basename.mt.json
+cp $BUILDDIR/$basename.mt.json $OUTDIR/$basename.mt.json || true

bin/build-stm32wl.sh

@@ -30,4 +30,4 @@ echo "Copying STM32 bin file"
 cp $BUILDDIR/$basename.bin $OUTDIR/$basename.bin
 
 echo "Copying manifest"
-cp $BUILDDIR/$basename.mt.json $OUTDIR/$basename.mt.json
+cp $BUILDDIR/$basename.mt.json $OUTDIR/$basename.mt.json || true

bin/config.d/lora-usb-meshstick-1262.yaml

@@ -0,0 +1,14 @@
+Lora:
+  Module: sx1262
+  CS: 0
+  IRQ: 6
+  Reset: 2
+  Busy: 4
+  RXen: 1
+  DIO2_AS_RF_SWITCH: true
+  spidev: ch341
+  DIO3_TCXO_VOLTAGE: true
+#  USB_Serialnum: 12345678
+  USB_PID: 0x5512
+  USB_VID: 0x1A86
+  SX126X_MAX_POWER: 22

bin/platformio-custom.py

@@ -2,11 +2,12 @@
 # trunk-ignore-all(ruff/F821)
 # trunk-ignore-all(flake8/F821): For SConstruct imports
 import sys
-from os.path import join, basename, isfile
+from os.path import join
 import subprocess
 import json
 import re
 from datetime import datetime
+from typing import Dict
 
 from readprops import readProps
 
@@ -14,8 +15,47 @@ Import("env")
 platform = env.PioPlatform()
 progname = env.get("PROGNAME")
 lfsbin = f"{progname.replace('firmware-', 'littlefs-')}.bin"
+manifest_ran = False
+
+def infer_architecture(board_cfg):
+    try:
+        mcu = board_cfg.get("build.mcu") if board_cfg else None
+    except KeyError:
+        mcu = None
+    except Exception:
+        mcu = None
+    if not mcu:
+        return None
+    mcu_l = str(mcu).lower()
+    if "esp32s3" in mcu_l:
+        return "esp32-s3"
+    if "esp32c6" in mcu_l:
+        return "esp32-c6"
+    if "esp32c3" in mcu_l:
+        return "esp32-c3"
+    if "esp32" in mcu_l:
+        return "esp32"
+    if "rp2040" in mcu_l:
+        return "rp2040"
+    if "rp2350" in mcu_l:
+        return "rp2350"
+    if "nrf52" in mcu_l or "nrf52840" in mcu_l:
+        return "nrf52840"
+    if "stm32" in mcu_l:
+        return "stm32"
+    return None
 
 def manifest_gather(source, target, env):
+    global manifest_ran
+    if manifest_ran:
+        return
+    # Skip manifest generation if we cannot determine architecture (host/native builds)
+    board_arch = infer_architecture(env.BoardConfig())
+    if not board_arch:
+        print(f"Skipping mtjson generation for unknown architecture (env={env.get('PIOENV')})")
+        manifest_ran = True
+        return
+    manifest_ran = True
     out = []
     board_platform = env.BoardConfig().get("platform")
     needs_ota_suffix = board_platform == "nordicnrf52"
@@ -47,14 +87,39 @@ def manifest_gather(source, target, env):
     manifest_write(out, env)
 
 def manifest_write(files, env):
+    # Defensive: also skip manifest writing if we cannot determine architecture
+    def get_project_option(name):
+        try:
+            return env.GetProjectOption(name)
+        except Exception:
+            return None
+
+    def get_project_option_any(names):
+        for name in names:
+            val = get_project_option(name)
+            if val is not None:
+                return val
+        return None
+
+    def as_bool(val):
+        return str(val).strip().lower() in ("1", "true", "yes", "on")
+
+    def as_int(val):
+        try:
+            return int(str(val), 10)
+        except (TypeError, ValueError):
+            return None
+
+    def as_list(val):
+        return [item.strip() for item in str(val).split(",") if item.strip()]
+
     manifest = {
         "version": verObj["long"],
         "build_epoch": build_epoch,
-        "board": env.get("PIOENV"),
+        "platformioTarget": env.get("PIOENV"),
         "mcu": env.get("BOARD_MCU"),
         "repo": repo_owner,
         "files": files,
-        "part": None,
         "has_mui": False,
         "has_inkhud": False,
     }
@@ -69,6 +134,51 @@ def manifest_write(files, env):
     if "MESHTASTIC_INCLUDE_INKHUD" in env.get("CPPDEFINES", []):
         manifest["has_inkhud"] = True
 
+    pioenv = env.get("PIOENV")
+    device_meta = {}
+    device_meta_fields = [
+        ("hwModel", ["custom_meshtastic_hw_model"], as_int),
+        ("hwModelSlug", ["custom_meshtastic_hw_model_slug"], str),
+        ("architecture", ["custom_meshtastic_architecture"], str),
+        ("activelySupported", ["custom_meshtastic_actively_supported"], as_bool),
+        ("displayName", ["custom_meshtastic_display_name"], str),
+        ("supportLevel", ["custom_meshtastic_support_level"], as_int),
+        ("images", ["custom_meshtastic_images"], as_list),
+        ("tags", ["custom_meshtastic_tags"], as_list),
+        ("requiresDfu", ["custom_meshtastic_requires_dfu"], as_bool),
+        ("partitionScheme", ["custom_meshtastic_partition_scheme"], str),
+        ("url", ["custom_meshtastic_url"], str),
+        ("key", ["custom_meshtastic_key"], str),
+        ("variant", ["custom_meshtastic_variant"], str),
+    ]
+
+
+    for manifest_key, option_keys, caster in device_meta_fields:
+        raw_val = get_project_option_any(option_keys)
+        if raw_val is None:
+            continue
+        parsed = caster(raw_val) if callable(caster) else raw_val
+        if parsed is not None and parsed != "":
+            device_meta[manifest_key] = parsed
+
+    # Determine architecture once; if we can't infer it, skip manifest generation
+    board_arch = device_meta.get("architecture") or infer_architecture(env.BoardConfig())
+    if not board_arch:
+        print(f"Skipping mtjson write for unknown architecture (env={env.get('PIOENV')})")
+        return
+
+    device_meta["architecture"] = board_arch
+
+    # Always set requiresDfu: true for nrf52840 targets
+    if board_arch == "nrf52840":
+        device_meta["requiresDfu"] = True
+
+    device_meta.setdefault("displayName", pioenv)
+    device_meta.setdefault("activelySupported", False)
+
+    if device_meta:
+        manifest.update(device_meta)
+
     # Write the manifest to the build directory
     with open(env.subst("$BUILD_DIR/${PROGNAME}.mt.json"), "w") as f:
         json.dump(manifest, f, indent=2)
@@ -166,8 +276,12 @@ def load_boot_logo(source, target, env):
 if ("HAS_TFT", 1) in env.get("CPPDEFINES", []):
     env.AddPreAction(f"$BUILD_DIR/{lfsbin}", load_boot_logo)
 
-mtjson_deps = ["buildprog"]
-if platform.name == "espressif32":
+board_arch = infer_architecture(env.BoardConfig())
+should_skip_manifest = board_arch is None
+
+# For host/native envs, avoid depending on 'buildprog' (some targets don't define it)
+mtjson_deps = [] if should_skip_manifest else ["buildprog"]
+if not should_skip_manifest and platform.name == "espressif32":
     # Build littlefs image as part of mtjson target
     # Equivalent to `pio run -t buildfs`
     target_lfs = env.DataToBin(
@@ -175,11 +289,27 @@ if platform.name == "espressif32":
     )
     mtjson_deps.append(target_lfs)
 
-env.AddCustomTarget(
-    name="mtjson",
-    dependencies=mtjson_deps,
-    actions=[manifest_gather],
-    title="Meshtastic Manifest",
-    description="Generating Meshtastic manifest JSON + Checksums",
-    always_build=False,
-)
+if should_skip_manifest:
+    def skip_manifest(source, target, env):
+        print(f"mtjson: skipped for native environment: {env.get('PIOENV')}")
+
+    env.AddCustomTarget(
+        name="mtjson",
+        dependencies=mtjson_deps,
+        actions=[skip_manifest],
+        title="Meshtastic Manifest (skipped)",
+        description="mtjson generation is skipped for native environments",
+        always_build=True,
+    )
+else:
+    env.AddCustomTarget(
+        name="mtjson",
+        dependencies=mtjson_deps,
+        actions=[manifest_gather],
+        title="Meshtastic Manifest",
+        description="Generating Meshtastic manifest JSON + Checksums",
+        always_build=True,
+    )
+
+    # Run manifest generation as part of the default build pipeline for non-native builds.
+    env.Default("mtjson")

bin/readprops.py

@@ -18,8 +18,9 @@ def readProps(prefsLoc):
 
     # Try to find current build SHA if if the workspace is clean.  This could fail if git is not installed
     try:
+        # Pin abbreviation length to keep local builds and CI matching (avoid auto-shortening)
         sha = (
-            subprocess.check_output(["git", "rev-parse", "--short", "HEAD"])
+            subprocess.check_output(["git", "rev-parse", "--short=7", "HEAD"])
             .decode("utf-8")
             .strip()
         )

src/buzz/BuzzerFeedbackThread.cpp

@@ -22,15 +22,19 @@ int BuzzerFeedbackThread::handleInputEvent(const InputEvent *event)
 
     // Handle different input events with appropriate buzzer feedback
     switch (event->inputEvent) {
-    case INPUT_BROKER_USER_PRESS:
-    case INPUT_BROKER_ALT_PRESS:
-        playClick(); // Low delay feedback
-        break;
-
+#ifdef INPUTDRIVER_ENCODER_TYPE
     case INPUT_BROKER_SELECT:
     case INPUT_BROKER_SELECT_LONG:
-        playBeep(); // Confirmation feedback
+        playClick();
         break;
+#else
+    case INPUT_BROKER_USER_PRESS:
+    case INPUT_BROKER_ALT_PRESS:
+    case INPUT_BROKER_SELECT:
+    case INPUT_BROKER_SELECT_LONG:
+        playBeep();
+        break;
+#endif
 
     case INPUT_BROKER_UP:
     case INPUT_BROKER_UP_LONG:

src/buzz/buzz.cpp

@@ -65,7 +65,7 @@ void playTones(const ToneDuration *tone_durations, int size)
 
 void playBeep()
 {
-    ToneDuration melody[] = {{NOTE_B3, DURATION_1_8}};
+    ToneDuration melody[] = {{NOTE_B3, DURATION_1_16}};
     playTones(melody, sizeof(melody) / sizeof(ToneDuration));
 }
 

src/detect/ScanI2CTwoWire.cpp

@@ -487,7 +487,7 @@ void ScanI2CTwoWire::scanPort(I2CPort port, uint8_t *address, uint8_t asize)
                 }
                 break;
             case TSL25911_ADDR:
-                registerValue = getRegisterValue(ScanI2CTwoWire::RegisterLocation(addr, 0x12), 1);
+                registerValue = getRegisterValue(ScanI2CTwoWire::RegisterLocation(addr, 0xA0 | 0x12), 1);
                 if (registerValue == 0x50) {
                     type = TSL2591;
                     logFoundDevice("TSL25911", (uint8_t)addr.address);

src/graphics/draw/MenuHandler.cpp

@@ -449,13 +449,14 @@ void menuHandler::clockMenu()
 }
 void menuHandler::messageResponseMenu()
 {
-    enum optionsNumbers { Back = 0, ViewMode, DeleteAll, DeleteOldest, ReplyMenu, Aloud, enumEnd };
+    enum optionsNumbers { Back = 0, ViewMode, DeleteAll, DeleteOldest, ReplyMenu, MuteChannel, Aloud, enumEnd };
 
     static const char *optionsArray[enumEnd];
     static int optionsEnumArray[enumEnd];
     int options = 0;
 
     auto mode = graphics::MessageRenderer::getThreadMode();
+    int threadChannel = graphics::MessageRenderer::getThreadChannel();
 
     optionsArray[options] = "Back";
     optionsEnumArray[options++] = Back;
@@ -467,6 +468,15 @@ void menuHandler::messageResponseMenu()
     optionsArray[options] = "View Chats";
     optionsEnumArray[options++] = ViewMode;
 
+    // If viewing ALL chats, hide “Mute Chat”
+    if (mode != graphics::MessageRenderer::ThreadMode::ALL && mode != graphics::MessageRenderer::ThreadMode::DIRECT) {
+        const uint8_t chIndex = (threadChannel != 0) ? (uint8_t)threadChannel : channels.getPrimaryIndex();
+        auto &chan = channels.getByIndex(chIndex);
+
+        optionsArray[options] = chan.settings.module_settings.is_muted ? "Unmute Channel" : "Mute Channel";
+        optionsEnumArray[options++] = MuteChannel;
+    }
+
     // Delete submenu
     optionsArray[options] = "Delete";
     optionsEnumArray[options++] = 900;
@@ -502,6 +512,14 @@ void menuHandler::messageResponseMenu()
             menuHandler::menuQueue = menuHandler::reply_menu;
             screen->runNow();
 
+        } else if (selected == MuteChannel) {
+            const uint8_t chIndex = (ch != 0) ? (uint8_t)ch : channels.getPrimaryIndex();
+            auto &chan = channels.getByIndex(chIndex);
+            if (chan.settings.has_module_settings) {
+                chan.settings.module_settings.is_muted = !chan.settings.module_settings.is_muted;
+                nodeDB->saveToDisk();
+            }
+
             // Delete submenu
         } else if (selected == 900) {
             menuHandler::menuQueue = menuHandler::delete_messages_menu;

src/mesh/FloodingRouter.cpp

@@ -4,6 +4,7 @@
 #include "configuration.h"
 #include "mesh-pb-constants.h"
 #include "meshUtils.h"
+#include "modules/TextMessageModule.h"
 #if !MESHTASTIC_EXCLUDE_TRACEROUTE
 #include "modules/TraceRouteModule.h"
 #endif
@@ -35,6 +36,10 @@ bool FloodingRouter::shouldFilterReceived(const meshtastic_MeshPacket *p)
         return true; // we handled it, so stop processing
     }
 
+    if (!seenRecently && !wasUpgraded && textMessageModule) {
+        seenRecently = textMessageModule->recentlySeen(p->id);
+    }
+
     if (seenRecently) {
         printPacket("Ignore dupe incoming msg", p);
         rxDupe++;

src/mesh/RadioInterface.cpp

@@ -246,7 +246,8 @@ uint32_t RadioInterface::getPacketTime(const meshtastic_MeshPacket *p, bool rece
 /** The delay to use for retransmitting dropped packets */
 uint32_t RadioInterface::getRetransmissionMsec(const meshtastic_MeshPacket *p)
 {
-    size_t numbytes = pb_encode_to_bytes(bytes, sizeof(bytes), &meshtastic_Data_msg, &p->decoded);
+    size_t numbytes =p->which_payload_variant == meshtastic_MeshPacket_decoded_tag ? 
+      pb_encode_to_bytes(bytes, sizeof(bytes), &meshtastic_Data_msg, &p->decoded) : p->encrypted.size+MESHTASTIC_HEADER_LENGTH;
     uint32_t packetAirtime = getPacketTime(numbytes + sizeof(PacketHeader));
     // Make sure enough time has elapsed for this packet to be sent and an ACK is received.
     // LOG_DEBUG("Waiting for flooding message with airtime %d and slotTime is %d", packetAirtime, slotTimeMsec);

src/mesh/SX126xInterface.cpp

@@ -53,13 +53,21 @@ template <typename T> bool SX126xInterface<T>::init()
 #endif
 
 #if defined(USE_GC1109_PA)
+    // GC1109 FEM chip initialization
+    // See variant.h for full pin mapping and control logic documentation
+
+    // VFEM_Ctrl (LORA_PA_POWER): Power enable for GC1109 LDO (always on)
     pinMode(LORA_PA_POWER, OUTPUT);
     digitalWrite(LORA_PA_POWER, HIGH);
 
+    // CSD (LORA_PA_EN): Chip enable - must be HIGH to enable GC1109 for both RX and TX
     pinMode(LORA_PA_EN, OUTPUT);
-    digitalWrite(LORA_PA_EN, LOW);
+    digitalWrite(LORA_PA_EN, HIGH);
+
+    // CPS (LORA_PA_TX_EN): PA mode select - HIGH enables full PA during TX, LOW for RX (don't care)
+    // Note: TX/RX path switching (CTX) is handled by DIO2 via SX126X_DIO2_AS_RF_SWITCH
     pinMode(LORA_PA_TX_EN, OUTPUT);
-    digitalWrite(LORA_PA_TX_EN, LOW);
+    digitalWrite(LORA_PA_TX_EN, LOW); // Start in RX-ready state
 #endif
 
 #ifdef RF95_FAN_EN
@@ -377,13 +385,13 @@ template <typename T> bool SX126xInterface<T>::sleep()
     return true;
 }
 
-/** Some boards require GPIO control of tx vs rx paths */
+/** Control PA mode for GC1109 FEM - CPS pin selects full PA (txon=true) or bypass mode (txon=false) */
 template <typename T> void SX126xInterface<T>::setTransmitEnable(bool txon)
 {
 #if defined(USE_GC1109_PA)
-    digitalWrite(LORA_PA_POWER, HIGH);
-    digitalWrite(LORA_PA_EN, HIGH);
-    digitalWrite(LORA_PA_TX_EN, txon ? 1 : 0);
+    digitalWrite(LORA_PA_POWER, HIGH);  // Ensure LDO is on
+    digitalWrite(LORA_PA_EN, HIGH);     // CSD=1: Chip enabled
+    digitalWrite(LORA_PA_TX_EN, txon ? 1 : 0);  // CPS: 1=full PA, 0=bypass (for RX, CPS is don't care)
 #endif
 }
 

src/modules/SystemCommandsModule.cpp

@@ -45,9 +45,9 @@ int SystemCommandsModule::handleInputEvent(const InputEvent *event)
     // Mute
     case INPUT_BROKER_MSG_MUTE_TOGGLE:
         if (moduleConfig.external_notification.enabled && externalNotificationModule) {
-            externalNotificationModule->setMute(externalNotificationModule->getMute());
+            externalNotificationModule->setMute(!externalNotificationModule->getMute());
             IF_SCREEN(if (!externalNotificationModule->getMute()) externalNotificationModule->stopNow(); screen->showSimpleBanner(
-                externalNotificationModule->getMute() ? "Notifications\nEnabled" : "Notifications\nDisabled", 3000);)
+                externalNotificationModule->getMute() ? "Notifications\nDisabled" : "Notifications\nEnabled", 3000);)
         }
         return 0;
     // Bluetooth

src/modules/TextMessageModule.cpp

@@ -17,6 +17,9 @@ ProcessMessage TextMessageModule::handleReceived(const meshtastic_MeshPacket &mp
     auto &p = mp.decoded;
     LOG_INFO("Received text msg from=0x%0x, id=0x%x, msg=%.*s", mp.from, mp.id, p.payload.size, p.payload.bytes);
 #endif
+    // add packet ID to the rolling list of packets
+    textPacketList[textPacketListIndex] = mp.id;
+    textPacketListIndex = (textPacketListIndex + 1) % TEXT_PACKET_LIST_SIZE;
 
     // We only store/display messages destined for us.
     devicestate.rx_text_message = mp;
@@ -47,3 +50,13 @@ bool TextMessageModule::wantPacket(const meshtastic_MeshPacket *p)
 {
     return MeshService::isTextPayload(p);
 }
+
+bool TextMessageModule::recentlySeen(uint32_t id)
+{
+    for (size_t i = 0; i < TEXT_PACKET_LIST_SIZE; i++) {
+        if (textPacketList[i] != 0 && textPacketList[i] == id) {
+            return true;
+        }
+    }
+    return false;
+}

src/modules/TextMessageModule.h

@@ -1,6 +1,7 @@
 #pragma once
 #include "Observer.h"
 #include "SinglePortModule.h"
+#define TEXT_PACKET_LIST_SIZE 50
 
 /**
  * Text message handling for Meshtastic.
@@ -19,6 +20,8 @@ class TextMessageModule : public SinglePortModule, public Observable<const mesht
      */
     TextMessageModule() : SinglePortModule("text", meshtastic_PortNum_TEXT_MESSAGE_APP) {}
 
+    bool recentlySeen(uint32_t id);
+
   protected:
     /** Called to handle a particular incoming message
      *
@@ -27,6 +30,10 @@ class TextMessageModule : public SinglePortModule, public Observable<const mesht
      */
     virtual ProcessMessage handleReceived(const meshtastic_MeshPacket &mp) override;
     virtual bool wantPacket(const meshtastic_MeshPacket *p) override;
+
+  private:
+    uint32_t textPacketList[TEXT_PACKET_LIST_SIZE] = {0};
+    size_t textPacketListIndex = 0;
 };
 
 extern TextMessageModule *textMessageModule;

src/platform/portduino/PortduinoGlue.cpp

@@ -366,6 +366,14 @@ void portduinoSetup()
                         cleanupNameForAutoconf("lora-hat-" + std::string(hat_vendor) + "-" + autoconf_product + ".yaml");
                 } else if (found_ch341) {
                     product_config = cleanupNameForAutoconf("lora-usb-" + std::string(autoconf_product) + ".yaml");
+                    // look for more data after the null terminator
+                    size_t len = strlen(autoconf_product);
+                    if (len < 74) {
+                        memcpy(portduino_config.device_id, autoconf_product + len + 1, 16);
+                        if (!memfll(portduino_config.device_id, '\0', 16) && !memfll(portduino_config.device_id, 0xff, 16)) {
+                            portduino_config.has_device_id = true;
+                        }
+                    }
                 }
 
                 // Don't try to automatically find config for a device with RAK eeprom.

src/platform/portduino/USBHal.h

@@ -64,7 +64,7 @@ class Ch341Hal : public RadioLibHal
     void getProductString(char *_product_string, size_t len)
     {
         len = len > 95 ? 95 : len;
-        strncpy(_product_string, pinedio.product_string, len);
+        memcpy(_product_string, pinedio.product_string, len);
     }
 
     void init() override {}

variants/esp32/diy/dr-dev/platformio.ini

@@ -1,5 +1,12 @@
 ; Port to Disaster Radio's ESP32-v3 Dev Board
 [env:meshtastic-dr-dev]
+custom_meshtastic_hw_model = 41
+custom_meshtastic_hw_model_slug = DR_DEV
+custom_meshtastic_architecture = esp32
+custom_meshtastic_actively_supported = false
+custom_meshtastic_display_name = DR-DEV
+custom_meshtastic_tags = DIY
+
 extends = esp32_base
 board = esp32doit-devkit-v1
 board_level = extra

variants/esp32/diy/hydra/platformio.ini

@@ -1,5 +1,13 @@
 ; Hydra - Meshtastic DIY v1 hardware with some specific changes
 [env:hydra]
+custom_meshtastic_hw_model = 39
+custom_meshtastic_hw_model_slug = HYDRA
+custom_meshtastic_architecture = esp32
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = Hydra
+custom_meshtastic_tags = DIY
+
 extends = esp32_base
 board = esp32doit-devkit-v1
 build_flags =

variants/esp32/diy/v1/platformio.ini

@@ -1,5 +1,14 @@
 ; Meshtastic DIY v1 by Nano VHF Schematic based on ESP32-WROOM-32 (38 pins) devkit & EBYTE E22 SX1262/SX1268 module
 [env:meshtastic-diy-v1]
+custom_meshtastic_hw_model = 39
+custom_meshtastic_hw_model_slug = DIY_V1
+custom_meshtastic_architecture = esp32
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = DIY V1
+custom_meshtastic_images = diy.svg
+custom_meshtastic_tags = DIY
+
 extends = esp32_base
 board = esp32doit-devkit-v1
 board_check = true

variants/esp32/heltec_v1/platformio.ini

@@ -1,4 +1,11 @@
 [env:heltec-v1]
+custom_meshtastic_hw_model = 11
+custom_meshtastic_hw_model_slug = HELTEC_V1
+custom_meshtastic_architecture = esp32
+custom_meshtastic_actively_supported = false
+custom_meshtastic_display_name = Heltec V1
+custom_meshtastic_tags = Heltec
+
 ;build_type = debug ; to make it possible to step through our jtag debugger 
 extends = esp32_base
 board_level = extra

variants/esp32/heltec_v2.1/platformio.ini

@@ -1,4 +1,11 @@
 [env:heltec-v2_1]
+custom_meshtastic_hw_model = 10
+custom_meshtastic_hw_model_slug = HELTEC_V2_1
+custom_meshtastic_architecture = esp32
+custom_meshtastic_actively_supported = false
+custom_meshtastic_display_name = Heltec V2.1
+custom_meshtastic_tags = Heltec
+
 board_level = extra
 ;build_type = debug ; to make it possible to step through our jtag debugger 
 extends = esp32_base

variants/esp32/heltec_v2/platformio.ini

@@ -1,4 +1,11 @@
 [env:heltec-v2_0]
+custom_meshtastic_hw_model = 5
+custom_meshtastic_hw_model_slug = HELTEC_V2_0
+custom_meshtastic_architecture = esp32
+custom_meshtastic_actively_supported = false
+custom_meshtastic_display_name = Heltec V2.0
+custom_meshtastic_tags = Heltec
+
 ;build_type = debug ; to make it possible to step through our jtag debugger
 board_level = extra
 extends = esp32_base

variants/esp32/m5stack_core/platformio.ini

@@ -1,4 +1,12 @@
 [env:m5stack-core]
+custom_meshtastic_hw_model = 42
+custom_meshtastic_hw_model_slug = M5STACK
+custom_meshtastic_architecture = esp32
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = M5 Stack
+custom_meshtastic_tags = M5Stack
+
 extends = esp32_base
 board = m5stack-core-esp32
 monitor_filters = esp32_exception_decoder

variants/esp32/nano-g1-explorer/platformio.ini

@@ -1,5 +1,13 @@
 ; The 1.0 release of the nano-g1-explorer board 
 [env:nano-g1-explorer]
+custom_meshtastic_hw_model = 17
+custom_meshtastic_hw_model_slug = NANO_G1_EXPLORER
+custom_meshtastic_architecture = esp32
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = Nano G1 Explorer
+custom_meshtastic_tags = B&Q
+
 extends = esp32_base
 board = ttgo-t-beam
 build_flags = 

variants/esp32/nano-g1/platformio.ini

@@ -1,5 +1,13 @@
 ; The 1.0 release of the nano-g1 board 
 [env:nano-g1]
+custom_meshtastic_hw_model = 14
+custom_meshtastic_hw_model_slug = NANO_G1
+custom_meshtastic_architecture = esp32
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = Nano G1
+custom_meshtastic_tags = B&Q
+
 extends = esp32_base
 board = ttgo-t-beam
 build_flags = 

variants/esp32/radiomaster_900_bandit_nano/platformio.ini

@@ -1,4 +1,12 @@
 [env:radiomaster_900_bandit_nano]
+custom_meshtastic_hw_model = 64
+custom_meshtastic_hw_model_slug = RADIOMASTER_900_BANDIT_NANO
+custom_meshtastic_architecture = esp32
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 2
+custom_meshtastic_display_name = RadioMaster 900 Bandit Nano
+custom_meshtastic_tags = RadioMaster
+
 extends = esp32_base
 board = esp32doit-devkit-v1
 build_flags =

variants/esp32/rak11200/platformio.ini

@@ -1,4 +1,13 @@
 [env:rak11200]
+custom_meshtastic_hw_model = 13
+custom_meshtastic_hw_model_slug = RAK11200
+custom_meshtastic_architecture = esp32
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = RAK WisBlock 11200
+custom_meshtastic_images = rak11200.svg
+custom_meshtastic_tags = RAK
+
 extends = esp32_base
 board = wiscore_rak11200
 board_level = pr

variants/esp32/station-g1/platformio.ini

@@ -1,5 +1,13 @@
 ; The 1.0 release of the nano-g1 board 
 [env:station-g1]
+custom_meshtastic_hw_model = 25
+custom_meshtastic_hw_model_slug = STATION_G1
+custom_meshtastic_architecture = esp32
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = Station G1
+custom_meshtastic_tags = B&Q
+
 extends = esp32_base
 board = ttgo-t-beam
 build_flags = 

variants/esp32/tbeam/platformio.ini

@@ -1,5 +1,14 @@
 ; The 1.0 release of the TBEAM board 
 [env:tbeam]
+custom_meshtastic_hw_model = 4
+custom_meshtastic_hw_model_slug = TBEAM
+custom_meshtastic_architecture = esp32
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = LILYGO T-Beam
+custom_meshtastic_images = tbeam.svg
+custom_meshtastic_tags = LilyGo
+
 extends = esp32_base
 board = ttgo-t-beam
 

variants/esp32/tbeam_v07/platformio.ini

@@ -1,5 +1,12 @@
 ; The original TBEAM board without the AXP power chip and a few other changes
 [env:tbeam0_7]
+custom_meshtastic_hw_model = 6
+custom_meshtastic_hw_model_slug = TBEAM_V0P7
+custom_meshtastic_architecture = esp32
+custom_meshtastic_actively_supported = false
+custom_meshtastic_display_name = LILYGO T-Beam V0.7
+custom_meshtastic_tags = LilyGo
+
 board_level = extra
 extends = esp32_base
 board = ttgo-t-beam

variants/esp32/tlora_v1/platformio.ini

@@ -1,4 +1,11 @@
 [env:tlora-v1]
+custom_meshtastic_hw_model = 2
+custom_meshtastic_hw_model_slug = TLORA_V1
+custom_meshtastic_architecture = esp32
+custom_meshtastic_actively_supported = false
+custom_meshtastic_display_name = LILYGO T-LoRa V1
+custom_meshtastic_tags = LilyGo
+
 board_level = extra
 extends = esp32_base
 board = ttgo-lora32-v1

variants/esp32/tlora_v2/platformio.ini

@@ -1,4 +1,11 @@
 [env:tlora-v2]
+custom_meshtastic_hw_model = 1
+custom_meshtastic_hw_model_slug = TLORA_V2
+custom_meshtastic_architecture = esp32
+custom_meshtastic_actively_supported = false
+custom_meshtastic_display_name = LILYGO T-LoRa V2
+custom_meshtastic_tags = LilyGo
+
 board_level = extra
 extends = esp32_base
 board = ttgo-lora32-v1

variants/esp32/tlora_v2_1_16/platformio.ini

@@ -1,4 +1,13 @@
 [env:tlora-v2-1-1_6]
+custom_meshtastic_hw_model = 3
+custom_meshtastic_hw_model_slug = TLORA_V2_1_1P6
+custom_meshtastic_architecture = esp32
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = LILYGO T-LoRa V2.1-1.6
+custom_meshtastic_images = tlora-v2-1-1_6.svg
+custom_meshtastic_tags = LilyGo
+
 extends = esp32_base
 board = ttgo-lora32-v21
 board_check = true

variants/esp32/tlora_v2_1_18/platformio.ini

@@ -1,4 +1,13 @@
 [env:tlora-v2-1-1_8]
+custom_meshtastic_hw_model = 15
+custom_meshtastic_hw_model_slug = TLORA_V2_1_1P8
+custom_meshtastic_architecture = esp32
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = LILYGO T-LoRa V2.1-1.8
+custom_meshtastic_images = tlora-v2-1-1_8.svg
+custom_meshtastic_tags = LilyGo, 2.4GHz
+
 extends = esp32_base
 board_level = extra
 board = ttgo-lora32-v21

variants/esp32c3/heltec_esp32c3/platformio.ini

@@ -1,4 +1,13 @@
 [env:heltec-ht62-esp32c3-sx1262]
+custom_meshtastic_hw_model = 53
+custom_meshtastic_hw_model_slug = HELTEC_HT62
+custom_meshtastic_architecture = esp32-c3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = Heltec HT62
+custom_meshtastic_images = heltec-ht62-esp32c3-sx1262.svg
+custom_meshtastic_tags = Heltec
+
 extends = esp32c3_base
 board = esp32-c3-devkitm-1
 board_level = pr

variants/esp32c6/m5stack_unitc6l/platformio.ini

@@ -1,4 +1,13 @@
 [env:m5stack-unitc6l]
+custom_meshtastic_hw_model = 111
+custom_meshtastic_hw_model_slug = M5STACK_C6L
+custom_meshtastic_architecture = esp32-c6
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = M5Stack Unit C6L
+custom_meshtastic_images = m5_c6l.svg
+custom_meshtastic_tags = M5Stack
+
 extends = esp32c6_base
 board = esp32-c6-devkitc-1
 ;OpenOCD flash method

variants/esp32s3/CDEBYTE_EoRa-S3/platformio.ini

@@ -1,4 +1,13 @@
 [env:CDEBYTE_EoRa-S3]
+custom_meshtastic_hw_model = 61
+custom_meshtastic_hw_model_slug = CDEBYTE_EORA_S3
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = EBYTE EoRa-S3
+custom_meshtastic_tags = EByte
+custom_meshtastic_requires_dfu = true
+
 extends = esp32s3_base
 board = CDEBYTE_EoRa-S3
 build_flags =

variants/esp32s3/ELECROW-ThinkNode-M2/platformio.ini

@@ -1,4 +1,14 @@
 [env:thinknode_m2]
+custom_meshtastic_hw_model = 90
+custom_meshtastic_hw_model_slug = THINKNODE_M2
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = ThinkNode M2
+custom_meshtastic_images = thinknode_m2.svg
+custom_meshtastic_tags = Elecrow
+custom_meshtastic_requires_dfu = false
+
 extends = esp32s3_base
 board = ESP32-S3-WROOM-1-N4
 build_flags =

variants/esp32s3/ELECROW-ThinkNode-M5/platformio.ini

@@ -1,4 +1,14 @@
 [env:thinknode_m5]
+custom_meshtastic_hw_model = 107
+custom_meshtastic_hw_model_slug = THINKNODE_M5
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = ThinkNode M5
+custom_meshtastic_images = thinknode_m1.svg
+custom_meshtastic_tags = Elecrow
+custom_meshtastic_requires_dfu = false
+
 extends = esp32s3_base
 board = ESP32-S3-WROOM-1-N4
 build_flags =

variants/esp32s3/elecrow_panel/platformio.ini

@@ -75,6 +75,17 @@ build_flags =
   -D DISPLAY_SET_RESOLUTION
 
 [env:elecrow-adv-24-28-tft]
+custom_meshtastic_hw_model = 97
+custom_meshtastic_hw_model_slug = CROWPANEL
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = Crowpanel Adv 2.4/2.8 TFT
+custom_meshtastic_images = crowpanel_2_4.svg, crowpanel_2_8.svg
+custom_meshtastic_tags = Elecrow
+custom_meshtastic_requires_dfu = true
+custom_meshtastic_partition_scheme = 16MB
+
 extends = crowpanel_small_esp32s3_base
 build_flags =
   ${crowpanel_small_esp32s3_base.build_flags}
@@ -99,6 +110,17 @@ build_flags =
   -D LGFX_TOUCH_ROTATION=0
 
 [env:elecrow-adv-35-tft]
+custom_meshtastic_hw_model = 97
+custom_meshtastic_hw_model_slug = CROWPANEL
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = Crowpanel Adv 3.5 TFT
+custom_meshtastic_images = crowpanel_3_5.svg
+custom_meshtastic_tags = Elecrow
+custom_meshtastic_requires_dfu = true
+custom_meshtastic_partition_scheme = 16MB
+
 extends = crowpanel_small_esp32s3_base
 board_level = pr
 build_flags =
@@ -127,6 +149,17 @@ build_flags =
 
 ; 4.3, 5.0, 7.0 inch 800x480 IPS (V1)
 [env:elecrow-adv1-43-50-70-tft]
+custom_meshtastic_hw_model = 97
+custom_meshtastic_hw_model_slug = CROWPANEL
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = Crowpanel Adv 4.3/5.0/7.0 TFT
+custom_meshtastic_images = crowpanel_5_0.svg, crowpanel_7_0.svg
+custom_meshtastic_tags = Elecrow
+custom_meshtastic_requires_dfu = true
+custom_meshtastic_partition_scheme = 16MB
+
 extends = crowpanel_large_esp32s3_base
 build_flags =
   ${crowpanel_large_esp32s3_base.build_flags}

variants/esp32s3/heltec_v3/platformio.ini

@@ -1,4 +1,14 @@
-[env:heltec-v3] 
+[env:heltec-v3]
+custom_meshtastic_hw_model = 43
+custom_meshtastic_hw_model_slug = HELTEC_V3
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = Heltec V3
+custom_meshtastic_images = heltec-v3.svg, heltec-v3-case.svg
+custom_meshtastic_tags = Heltec
+custom_meshtastic_partition_scheme = 8MB
+ 
 extends = esp32s3_base
 board = heltec_wifi_lora_32_V3
 board_level = pr

variants/esp32s3/heltec_v4/platformio.ini

@@ -10,6 +10,17 @@ build_flags =
 
 
 [env:heltec-v4]
+custom_meshtastic_hw_model = 110
+custom_meshtastic_hw_model_slug = HELTEC_V4
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = Heltec V4
+custom_meshtastic_images = heltec_v4.svg
+custom_meshtastic_tags = Heltec
+custom_meshtastic_requires_dfu = true
+custom_meshtastic_partition_scheme = 16MB
+
 extends = heltec_v4_base
 build_flags = 
   ${heltec_v4_base.build_flags}

variants/esp32s3/heltec_v4/variant.h

@@ -29,10 +29,32 @@
 #define SX126X_DIO2_AS_RF_SWITCH
 #define SX126X_DIO3_TCXO_VOLTAGE 1.8
 
-#define USE_GC1109_PA   // We have a GC1109 power amplifier+attenuator
-#define LORA_PA_POWER 7 // power en
-#define LORA_PA_EN 2
-#define LORA_PA_TX_EN 46 // enable tx
+// ---- GC1109 RF FRONT END CONFIGURATION ----
+// The Heltec V4 uses a GC1109 FEM chip with integrated PA and LNA
+// RF path: SX1262 -> GC1109 PA -> Pi attenuator -> Antenna
+// Measured net TX gain (non-linear due to PA compression):
+//   +11dB at 0-15dBm input  (e.g., 10dBm in -> 21dBm out)
+//   +10dB at 16-17dBm input
+//   +9dB  at 18-19dBm input
+//   +7dB  at 21dBm input    (e.g., 21dBm in -> 28dBm out max)
+// Control logic (from GC1109 datasheet):
+//   Shutdown:        CSD=0, CTX=X, CPS=X
+//   Receive LNA:     CSD=1, CTX=0, CPS=X  (17dB gain, 2dB NF)
+//   Transmit bypass: CSD=1, CTX=1, CPS=0  (~1dB loss, no PA)
+//   Transmit PA:     CSD=1, CTX=1, CPS=1  (full PA enabled)
+// Pin mapping:
+//   CTX (pin 6)  -> SX1262 DIO2: TX/RX path select (automatic via SX126X_DIO2_AS_RF_SWITCH)
+//   CSD (pin 4)  -> GPIO2: Chip enable (HIGH=on, LOW=shutdown)
+//   CPS (pin 5)  -> GPIO46: PA mode select (HIGH=full PA, LOW=bypass)
+//   VCC0/VCC1    -> Vfem via U3 LDO, controlled by GPIO7
+#define USE_GC1109_PA
+#define LORA_PA_POWER 7  // VFEM_Ctrl - GC1109 LDO power enable
+#define LORA_PA_EN 2     // CSD - GC1109 chip enable (HIGH=on)
+#define LORA_PA_TX_EN 46 // CPS - GC1109 PA mode (HIGH=full PA, LOW=bypass)
+
+// GC1109 FEM: TX/RX path switching is handled by DIO2 -> CTX pin (via SX126X_DIO2_AS_RF_SWITCH)
+// GPIO46 is CPS (PA mode), not TX control - setTransmitEnable() handles it in SX126xInterface.cpp
+// Do NOT use SX126X_TXEN/RXEN as that would cause double-control of GPIO46
 
 #if HAS_TFT
 #define USE_TFTDISPLAY 1

variants/esp32s3/heltec_vision_master_e213/platformio.ini

@@ -1,4 +1,15 @@
 [env:heltec-vision-master-e213]
+custom_meshtastic_hw_model = 67
+custom_meshtastic_hw_model_slug = HELTEC_VISION_MASTER_E213
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = Heltec Vision Master E213
+custom_meshtastic_images = heltec-vision-master-e213.svg
+custom_meshtastic_tags = Heltec
+custom_meshtastic_requires_dfu = true
+custom_meshtastic_partition_scheme = 8MB
+
 extends = esp32s3_base
 board = heltec_vision_master_e213
 board_build.partitions = default_8MB.csv

variants/esp32s3/heltec_vision_master_e290/platformio.ini

@@ -1,5 +1,16 @@
 ; Using the original screen class
 [env:heltec-vision-master-e290]
+custom_meshtastic_hw_model = 68
+custom_meshtastic_hw_model_slug = HELTEC_VISION_MASTER_E290
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = Heltec Vision Master E290
+custom_meshtastic_images = heltec-vision-master-e290.svg
+custom_meshtastic_tags = Heltec
+custom_meshtastic_requires_dfu = true
+custom_meshtastic_partition_scheme = 8MB
+
 extends = esp32s3_base
 board = heltec_vision_master_e290
 board_build.partitions = default_8MB.csv

variants/esp32s3/heltec_vision_master_t190/platformio.ini

@@ -1,4 +1,15 @@
 [env:heltec-vision-master-t190]
+custom_meshtastic_hw_model = 66
+custom_meshtastic_hw_model_slug = HELTEC_VISION_MASTER_T190
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = Heltec Vision Master T190
+custom_meshtastic_images = heltec-vision-master-t190.svg
+custom_meshtastic_tags = Heltec
+custom_meshtastic_requires_dfu = true
+custom_meshtastic_partition_scheme = 8MB
+
 extends = esp32s3_base
 board = heltec_vision_master_t190
 board_build.partitions = default_8MB.csv

variants/esp32s3/heltec_wireless_paper/platformio.ini

@@ -1,5 +1,15 @@
 ; Using the original screen class
 [env:heltec-wireless-paper]
+custom_meshtastic_hw_model = 49
+custom_meshtastic_hw_model_slug = HELTEC_WIRELESS_PAPER
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = Heltec Wireless Paper
+custom_meshtastic_images = heltec-wireless-paper.svg
+custom_meshtastic_tags = Heltec
+custom_meshtastic_partition_scheme = 8MB
+
 extends = esp32s3_base
 board = heltec_wifi_lora_32_V3
 board_build.partitions = default_8MB.csv

variants/esp32s3/heltec_wireless_paper_v1/platformio.ini

@@ -1,4 +1,14 @@
 [env:heltec-wireless-paper-v1_0]
+custom_meshtastic_hw_model = 57
+custom_meshtastic_hw_model_slug = HELTEC_WIRELESS_PAPER_V1_0
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = false
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = Heltec Wireless Paper V1.0
+custom_meshtastic_images = heltec-wireless-paper-v1_0.svg
+custom_meshtastic_tags = Heltec
+custom_meshtastic_partition_scheme = 8MB
+
 extends = esp32s3_base
 board_level = extra
 board = heltec_wifi_lora_32_V3

variants/esp32s3/heltec_wireless_tracker/platformio.ini

@@ -1,4 +1,15 @@
 [env:heltec-wireless-tracker]
+custom_meshtastic_hw_model = 48
+custom_meshtastic_hw_model_slug = HELTEC_WIRELESS_TRACKER
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = Heltec Wireless Tracker V1.1
+custom_meshtastic_images = heltec-wireless-tracker.svg
+custom_meshtastic_tags = Heltec
+custom_meshtastic_requires_dfu = true
+custom_meshtastic_partition_scheme = 8MB
+
 extends = esp32s3_base
 board = heltec_wireless_tracker
 board_build.partitions = default_8MB.csv

variants/esp32s3/heltec_wireless_tracker_V1_0/platformio.ini

@@ -1,4 +1,14 @@
 [env:heltec-wireless-tracker-V1-0]
+custom_meshtastic_hw_model = 58
+custom_meshtastic_hw_model_slug = HELTEC_WIRELESS_TRACKER_V1_0
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = false
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = Heltec Wireless Tracker V1.0
+custom_meshtastic_images = heltec-wireless-tracker.svg
+custom_meshtastic_requires_dfu = true
+custom_meshtastic_partition_scheme = 8MB
+
 extends = esp32s3_base
 board_level = extra
 board = heltec_wireless_tracker

variants/esp32s3/heltec_wireless_tracker_v2/variant.h

@@ -73,7 +73,29 @@
 #define SX126X_DIO2_AS_RF_SWITCH
 #define SX126X_DIO3_TCXO_VOLTAGE 1.8
 
-#define USE_GC1109_PA   // We have a GC1109 power amplifier+attenuator
-#define LORA_PA_POWER 7 // power en
-#define LORA_PA_EN 4
-#define LORA_PA_TX_EN 46 // enable tx
+// ---- GC1109 RF FRONT END CONFIGURATION ----
+// The Heltec Wireless Tracker V2 uses a GC1109 FEM chip with integrated PA and LNA
+// RF path: SX1262 -> GC1109 PA -> Pi attenuator -> Antenna
+// Measured net TX gain (non-linear due to PA compression):
+//   +11dB at 0-15dBm input  (e.g., 10dBm in -> 21dBm out)
+//   +10dB at 16-17dBm input
+//   +9dB  at 18-19dBm input
+//   +7dB  at 21dBm input    (e.g., 21dBm in -> 28dBm out max)
+// Control logic (from GC1109 datasheet):
+//   Shutdown:        CSD=0, CTX=X, CPS=X
+//   Receive LNA:     CSD=1, CTX=0, CPS=X  (17dB gain, 2dB NF)
+//   Transmit bypass: CSD=1, CTX=1, CPS=0  (~1dB loss, no PA)
+//   Transmit PA:     CSD=1, CTX=1, CPS=1  (full PA enabled)
+// Pin mapping:
+//   CTX (pin 6)  -> SX1262 DIO2: TX/RX path select (automatic via SX126X_DIO2_AS_RF_SWITCH)
+//   CSD (pin 4)  -> GPIO4: Chip enable (HIGH=on, LOW=shutdown)
+//   CPS (pin 5)  -> GPIO46: PA mode select (HIGH=full PA, LOW=bypass)
+//   VCC0/VCC1    -> Vfem via U3 LDO, controlled by GPIO7
+#define USE_GC1109_PA
+#define LORA_PA_POWER 7  // VFEM_Ctrl - GC1109 LDO power enable
+#define LORA_PA_EN 4     // CSD - GC1109 chip enable (HIGH=on)
+#define LORA_PA_TX_EN 46 // CPS - GC1109 PA mode (HIGH=full PA, LOW=bypass)
+
+// GC1109 FEM: TX/RX path switching is handled by DIO2 -> CTX pin (via SX126X_DIO2_AS_RF_SWITCH)
+// GPIO46 is CPS (PA mode), not TX control - setTransmitEnable() handles it in SX126xInterface.cpp
+// Do NOT use SX126X_TXEN/RXEN as that would cause double-control of GPIO46

variants/esp32s3/heltec_wsl_v3/platformio.ini

@@ -1,4 +1,14 @@
-[env:heltec-wsl-v3] 
+[env:heltec-wsl-v3]
+custom_meshtastic_hw_model = 44
+custom_meshtastic_hw_model_slug = HELTEC_WSL_V3
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = Heltec Wireless Stick Lite V3
+custom_meshtastic_images = heltec-wsl-v3.svg
+custom_meshtastic_tags = Heltec
+custom_meshtastic_partition_scheme = 8MB
+ 
 extends = esp32s3_base
 board = heltec_wifi_lora_32_V3
 board_build.partitions = default_8MB.csv

variants/esp32s3/picomputer-s3/platformio.ini

@@ -1,4 +1,12 @@
 [env:picomputer-s3]
+custom_meshtastic_hw_model = 52
+custom_meshtastic_hw_model_slug = PICOMPUTER_S3
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = Pi Computer S3
+custom_meshtastic_partition_scheme = 8MB
+
 extends = esp32s3_base
 board = bpi_picow_esp32_s3
 board_check = true

variants/esp32s3/rak3312/platformio.ini

@@ -1,4 +1,15 @@
 [env:rak3312]
+custom_meshtastic_hw_model = 106
+custom_meshtastic_hw_model_slug = RAK3312
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = RAK3312
+custom_meshtastic_images = rak_3312.svg
+custom_meshtastic_tags = RAK
+custom_meshtastic_requires_dfu = false
+custom_meshtastic_partition_scheme = 16MB
+
 extends = esp32s3_base
 board = wiscore_rak3312
 board_level = pr

variants/esp32s3/seeed-sensecap-indicator/platformio.ini

@@ -1,5 +1,16 @@
 ; Seeed Studio SenseCAP Indicator
 [env:seeed-sensecap-indicator]
+custom_meshtastic_hw_model = 70
+custom_meshtastic_hw_model_slug = SENSECAP_INDICATOR
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = Seeed SenseCAP Indicator
+custom_meshtastic_images = seeed-sensecap-indicator.svg
+custom_meshtastic_tags = Seeed
+custom_meshtastic_partition_scheme = 8MB
+ = true
+
 extends = esp32s3_base
 platform_packages =
     platformio/framework-arduinoespressif32 @ https://github.com/mverch67/arduino-esp32/archive/aef7fef6de3329ed6f75512d46d63bba12b09bb5.zip ; add_tca9535 (based on 2.0.16)

variants/esp32s3/seeed_xiao_s3/platformio.ini

@@ -1,4 +1,15 @@
 [env:seeed-xiao-s3]
+custom_meshtastic_hw_model = 81
+custom_meshtastic_hw_model_slug = SEEED_XIAO_S3
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = Seeed Xiao ESP32-S3
+custom_meshtastic_images = seeed-xiao-s3.svg
+custom_meshtastic_tags = Seeed
+custom_meshtastic_requires_dfu = true
+custom_meshtastic_partition_scheme = 8MB
+
 extends = esp32s3_base
 board = seeed-xiao-s3
 board_level = pr

variants/esp32s3/station-g2/platformio.ini

@@ -1,4 +1,15 @@
 [env:station-g2]
+custom_meshtastic_hw_model = 31
+custom_meshtastic_hw_model_slug = STATION_G2
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 2
+custom_meshtastic_display_name = Station G2
+custom_meshtastic_images = station-g2.svg
+custom_meshtastic_tags = B&Q
+custom_meshtastic_requires_dfu = true
+custom_meshtastic_partition_scheme = 16MB
+
 extends = esp32s3_base
 board = station-g2
 board_level = pr

variants/esp32s3/t-deck-pro/platformio.ini

@@ -1,4 +1,15 @@
 [env:t-deck-pro]
+custom_meshtastic_hw_model = 102
+custom_meshtastic_hw_model_slug = T_DECK_PRO
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = LILYGO T-Deck Pro
+custom_meshtastic_images = tdeck_pro.svg
+custom_meshtastic_tags = LilyGo
+custom_meshtastic_requires_dfu = true
+custom_meshtastic_partition_scheme = 16MB
+
 extends = esp32s3_base
 board = t-deck-pro
 board_check = true

variants/esp32s3/t-deck/platformio.ini

@@ -1,5 +1,16 @@
 ; LilyGo T-Deck
 [env:t-deck]
+custom_meshtastic_hw_model = 50
+custom_meshtastic_hw_model_slug = T_DECK
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = LILYGO T-Deck
+custom_meshtastic_images = t-deck.svg
+custom_meshtastic_tags = LilyGo
+custom_meshtastic_requires_dfu = true
+custom_meshtastic_partition_scheme = 16MB
+
 extends = esp32s3_base
 board = t-deck
 board_check = true

variants/esp32s3/t-watch-s3/platformio.ini

@@ -1,5 +1,15 @@
 ; LilyGo T-Watch S3
 [env:t-watch-s3]
+custom_meshtastic_hw_model = 51
+custom_meshtastic_hw_model_slug = T_WATCH_S3
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = LILYGO T-Watch S3
+custom_meshtastic_images = t-watch-s3.svg
+custom_meshtastic_tags = LilyGo
+custom_meshtastic_partition_scheme = 8MB
+
 extends = esp32s3_base
 board = t-watch-s3
 board_check = true

variants/esp32s3/tbeam-s3-core/platformio.ini

@@ -1,5 +1,16 @@
 ; The 1.0 release of the LilyGo TBEAM-S3-Core board 
 [env:tbeam-s3-core]
+custom_meshtastic_hw_model = 12
+custom_meshtastic_hw_model_slug = LILYGO_TBEAM_S3_CORE
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = LILYGO T-Beam Supreme
+custom_meshtastic_images = tbeam-s3-core.svg
+custom_meshtastic_tags = LilyGo
+custom_meshtastic_requires_dfu = true
+custom_meshtastic_partition_scheme = 8MB
+
 extends = esp32s3_base
 board = tbeam-s3-core
 board_build.partitions = default_8MB.csv

variants/esp32s3/tlora-pager/platformio.ini

@@ -1,5 +1,16 @@
 ; LilyGo T-Lora-Pager
 [env:tlora-pager]
+custom_meshtastic_hw_model = 103
+custom_meshtastic_hw_model_slug = T_LORA_PAGER
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = LILYGO T-LoRa Pager
+custom_meshtastic_images = lilygo-tlora-pager.svg
+custom_meshtastic_tags = LilyGo
+custom_meshtastic_requires_dfu = true
+custom_meshtastic_partition_scheme = 16MB
+
 extends = esp32s3_base
 board = t-deck-pro ; same as T-Deck Pro
 board_check = true

variants/esp32s3/tlora_t3s3_epaper/platformio.ini

@@ -1,4 +1,14 @@
 [env:tlora-t3s3-epaper]
+custom_meshtastic_hw_model = 16
+custom_meshtastic_hw_model_slug = TLORA_T3_S3
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = LILYGO T-LoRa T3-S3 E-Ink
+custom_meshtastic_images = tlora-t3s3-epaper.svg
+custom_meshtastic_tags = LilyGo
+custom_meshtastic_requires_dfu = true
+
 extends = esp32s3_base
 board = tlora-t3s3-v1
 board_check = true

variants/esp32s3/tlora_t3s3_v1/platformio.ini

@@ -1,4 +1,14 @@
 [env:tlora-t3s3-v1]
+custom_meshtastic_hw_model = 16
+custom_meshtastic_hw_model_slug = TLORA_T3_S3
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = LILYGO T-LoRa T3-S3
+custom_meshtastic_images = tlora-t3s3-v1.svg
+custom_meshtastic_tags = LilyGo
+custom_meshtastic_requires_dfu = true
+
 extends = esp32s3_base
 board = tlora-t3s3-v1
 board_check = true

variants/esp32s3/tracksenger/platformio.ini

@@ -1,4 +1,13 @@
 [env:tracksenger]
+custom_meshtastic_hw_model = 48
+custom_meshtastic_hw_model_slug = HELTEC_WIRELESS_TRACKER
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = TrackSenger (small TFT)
+custom_meshtastic_requires_dfu = true
+custom_meshtastic_partition_scheme = 8MB
+
 extends = esp32s3_base
 board = heltec_wireless_tracker
 board_build.partitions = default_8MB.csv
@@ -16,6 +25,15 @@ lib_deps =
   lovyan03/LovyanGFX@1.2.7
 
 [env:tracksenger-lcd]
+custom_meshtastic_hw_model = 48
+custom_meshtastic_hw_model_slug = HELTEC_WIRELESS_TRACKER
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = false
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = TrackSenger (big TFT)
+custom_meshtastic_requires_dfu = true
+custom_meshtastic_partition_scheme = 8MB
+
 extends = esp32s3_base
 board = heltec_wireless_tracker
 board_build.partitions = default_8MB.csv
@@ -33,6 +51,14 @@ lib_deps =
   lovyan03/LovyanGFX@1.2.7
 
 [env:tracksenger-oled]
+custom_meshtastic_hw_model = 48
+custom_meshtastic_hw_model_slug = HELTEC_WIRELESS_TRACKER
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = TrackSenger (big OLED)
+custom_meshtastic_partition_scheme = 8MB
+
 extends = esp32s3_base
 board = heltec_wireless_tracker
 board_build.partitions = default_8MB.csv

variants/esp32s3/unphone/platformio.ini

@@ -1,6 +1,15 @@
 ; platformio.ini for unphone meshtastic
 
 [env:unphone]
+custom_meshtastic_hw_model = 59
+custom_meshtastic_hw_model_slug = UNPHONE
+custom_meshtastic_architecture = esp32-s3
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = unPhone
+custom_meshtastic_requires_dfu = true
+custom_meshtastic_partition_scheme = 8MB
+
 extends = esp32s3_base
 board = unphone
 board_build.partitions = partition-table-8MB.csv

variants/nrf52840/ELECROW-ThinkNode-M1/platformio.ini

@@ -1,5 +1,14 @@
 ; First prototype eink/nrf52840/sx1262 device
 [env:thinknode_m1]
+custom_meshtastic_hw_model = 89
+custom_meshtastic_hw_model_slug = THINKNODE_M1
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = ThinkNode M1
+custom_meshtastic_images = thinknode_m1.svg
+custom_meshtastic_tags = Elecrow
+
 extends = nrf52840_base
 board = ThinkNode-M1
 board_check = true

variants/nrf52840/ELECROW-ThinkNode-M3/platformio.ini

@@ -1,8 +1,17 @@
 [env:thinknode_m3]
+custom_meshtastic_support_level = 1
+custom_meshtastic_images = thinknode_m3.svg
+custom_meshtastic_tags = Elecrow
+
 extends = nrf52840_base
 board = ThinkNode-M3
 board_check = true
 debug_tool = jlink
+custom_meshtastic_hw_model = 115
+custom_meshtastic_hw_model_slug = THINKNODE_M3
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_display_name = Elecrow ThinkNode M3
+custom_meshtastic_actively_supported = true
 build_flags = 
   ${nrf52840_base.build_flags} 
   -Ivariants/nrf52840/ELECROW-ThinkNode-M3

variants/nrf52840/ELECROW-ThinkNode-M6/platformio.ini

@@ -1,5 +1,14 @@
 ; ThinkNode M6 - Outdoor Solar Power nrf52840/sx1262 device
 [env:thinknode_m6]
+custom_meshtastic_hw_model = 120
+custom_meshtastic_hw_model_slug = THINKNODE_M6
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = false
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = ThinkNode M6
+custom_meshtastic_images = thinknode_m6.svg
+custom_meshtastic_tags = Elecrow
+
 extends = nrf52840_base
 board = ThinkNode-M6
 board_check = true

variants/nrf52840/canaryone/platformio.ini

@@ -1,5 +1,13 @@
 ; Public Beta oled/nrf52840/sx1262 device
 [env:canaryone]
+custom_meshtastic_hw_model = 29
+custom_meshtastic_hw_model_slug = CANARYONE
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = Canary One
+custom_meshtastic_tags = Canary
+
 extends = nrf52840_base
 board = canaryone
 debug_tool = jlink

variants/nrf52840/diy/nrf52_promicro_diy_tcxo/platformio.ini

@@ -1,5 +1,15 @@
 ; Promicro + E22(0)-xxxM / HT-RA62 modules board variant - DIY - with TCXO
 [env:nrf52_promicro_diy_tcxo]
+custom_meshtastic_hw_model = 63
+custom_meshtastic_hw_model_slug = NRF52_PROMICRO_DIY
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = NRF52 Pro-micro DIY
+custom_meshtastic_images = promicro.svg
+custom_meshtastic_tags = DIY
+custom_meshtastic_requires_dfu = true
+
 extends = nrf52840_base
 board = promicro-nrf52840
 build_flags = ${nrf52840_base.build_flags}

variants/nrf52840/heltec_mesh_node_t114/platformio.ini

@@ -1,5 +1,14 @@
 ; First prototype nrf52840/sx1262 device
 [env:heltec-mesh-node-t114]
+custom_meshtastic_hw_model = 69
+custom_meshtastic_hw_model_slug = HELTEC_MESH_NODE_T114
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = Heltec Mesh Node T114
+custom_meshtastic_images = heltec-mesh-node-t114.svg, heltec-mesh-node-t114-case.svg
+custom_meshtastic_tags = Heltec
+
 extends = nrf52840_base
 board = heltec_mesh_node_t114
 board_level = pr

variants/nrf52840/heltec_mesh_pocket/platformio.ini

@@ -1,8 +1,20 @@
 ; First prototype nrf52840/sx1262 device
 [env:heltec-mesh-pocket-5000]
+custom_meshtastic_support_level = 1
+custom_meshtastic_images = heltec_mesh_pocket.svg
+custom_meshtastic_tags = Heltec
+
 extends = nrf52840_base
 board = heltec_mesh_pocket
 debug_tool = jlink
+custom_device_hw_model = 94
+custom_meshtastic_hw_model = 94
+custom_meshtastic_hw_model_slug = HELTEC_MESH_POCKET
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_display_name = Heltec Mesh Pocket
+custom_meshtastic_actively_supported = true
+custom_meshtastic_variant = 5000mAh
+custom_meshtastic_key = heltec_mesh_pocket
 
 # add -DCFG_SYSVIEW if you want to use the Segger systemview tool for OS profiling.
 build_flags = ${nrf52840_base.build_flags}
@@ -31,6 +43,13 @@ lib_deps =
 [env:heltec-mesh-pocket-5000-inkhud]
 extends = nrf52840_base, inkhud
 board = heltec_mesh_pocket
+custom_meshtastic_hw_model = 94
+custom_meshtastic_hw_model_slug = HELTEC_MESH_POCKET
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_display_name = Heltec Mesh Pocket
+custom_meshtastic_actively_supported = true
+custom_meshtastic_variant = 5000mAh InkHUD
+custom_meshtastic_key = heltec_mesh_pocket
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/heltec_mesh_pocket> ${inkhud.build_src_filter}
 build_flags = 
   ${inkhud.build_flags}
@@ -45,9 +64,20 @@ lib_deps =
 
 ; First prototype nrf52840/sx1262 device
 [env:heltec-mesh-pocket-10000]
+custom_meshtastic_support_level = 1
+custom_meshtastic_images = heltec_mesh_pocket.svg
+custom_meshtastic_tags = Heltec
+
 extends = nrf52840_base
 board = heltec_mesh_pocket
 debug_tool = jlink
+custom_meshtastic_hw_model = 94
+custom_meshtastic_hw_model_slug = HELTEC_MESH_POCKET
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_display_name = Heltec Mesh Pocket
+custom_meshtastic_actively_supported = true
+custom_meshtastic_variant = 10000mAh
+custom_meshtastic_key = heltec_mesh_pocket
 
 # add -DCFG_SYSVIEW if you want to use the Segger systemview tool for OS profiling.
 build_flags = ${nrf52840_base.build_flags}
@@ -76,6 +106,13 @@ lib_deps =
 [env:heltec-mesh-pocket-10000-inkhud]
 extends = nrf52840_base, inkhud
 board = heltec_mesh_pocket
+custom_meshtastic_hw_model = 94
+custom_meshtastic_hw_model_slug = HELTEC_MESH_POCKET
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_display_name = Heltec Mesh Pocket
+custom_meshtastic_actively_supported = true
+custom_meshtastic_variant = 10000mAh InkHUD
+custom_meshtastic_key = heltec_mesh_pocket
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/heltec_mesh_pocket> ${inkhud.build_src_filter}
 build_flags = 
   ${inkhud.build_flags}

variants/nrf52840/heltec_mesh_solar/platformio.ini

@@ -19,6 +19,15 @@ lib_deps =
   bblanchon/ArduinoJson@6.21.4
 
 [env:heltec-mesh-solar]
+custom_meshtastic_hw_model = 108
+custom_meshtastic_hw_model_slug = HELTEC_MESH_SOLAR
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = false
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = Heltec MeshSolar
+custom_meshtastic_images = heltec-mesh-solar.svg
+custom_meshtastic_tags = Heltec
+
 extends = heltec_mesh_solar_base
 build_flags = ${heltec_mesh_solar_base.build_flags}
     -DSPI_INTERFACES_COUNT=1

variants/nrf52840/muzi_base/platformio.ini

@@ -1,4 +1,13 @@
 [env:muzi-base]
+custom_meshtastic_hw_model = 93
+custom_meshtastic_hw_model_slug = MUZI_BASE
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = muzi BASE
+custom_meshtastic_images = muzi_base.svg
+custom_meshtastic_tags = muzi
+
 extends = nrf52840_base
 board = muzi-base
 build_flags = ${nrf52840_base.build_flags}

variants/nrf52840/nano-g2-ultra/platformio.ini

@@ -1,5 +1,14 @@
 ; First prototype eink/nrf52840/sx1262 device
 [env:nano-g2-ultra]
+custom_meshtastic_hw_model = 18
+custom_meshtastic_hw_model_slug = NANO_G2_ULTRA
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 2
+custom_meshtastic_display_name = Nano G2 Ultra
+custom_meshtastic_images = nano-g2-ultra.svg
+custom_meshtastic_tags = B&Q
+
 extends = nrf52840_base
 board = nano-g2-ultra
 debug_tool = jlink

variants/nrf52840/r1-neo/platformio.ini

@@ -1,5 +1,14 @@
 ; The R1 Neo board
 [env:r1-neo]
+custom_meshtastic_hw_model = 101
+custom_meshtastic_hw_model_slug = MUZI_R1_NEO
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = muzi R1 Neo
+custom_meshtastic_images = muzi_r1_neo.svg
+custom_meshtastic_tags = muzi
+
 extends = nrf52840_base
 board = r1-neo
 board_check = true

variants/nrf52840/rak2560/platformio.ini

@@ -1,5 +1,14 @@
 ; Firmware for the WisMesh HUB RAK2560, including a onewire module to talk to the RAK 9154 solar battery.
 [env:rak2560]
+custom_meshtastic_hw_model = 22
+custom_meshtastic_hw_model_slug = WISMESH_HUB
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = RAK WisMesh Repeater
+custom_meshtastic_images = rak2560.svg
+custom_meshtastic_tags = RAK
+
 extends = nrf52840_base
 board = wiscore_rak4631
 board_check = true

variants/nrf52840/rak3401_1watt/platformio.ini

@@ -1,5 +1,15 @@
 ; The very slick RAK wireless RAK 4631 / 4630 board - Unified firmware for 5005/19003, with or without OLED RAK 1921
 [env:rak3401-1watt]
+custom_meshtastic_hw_model = 117
+custom_meshtastic_hw_model_slug = RAK3401
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = RAK3401 1W
+custom_meshtastic_images = rak3401.svg
+custom_meshtastic_tags = RAK
+custom_meshtastic_requires_dfu = true
+
 extends = nrf52840_base
 board = wiscore_rak4631
 board_check = true

variants/nrf52840/rak4631/platformio.ini

@@ -1,5 +1,14 @@
 ; The very slick RAK wireless RAK 4631 / 4630 board - Unified firmware for 5005/19003, with or without OLED RAK 1921
 [env:rak4631]
+custom_meshtastic_hw_model = 9
+custom_meshtastic_hw_model_slug = RAK4631
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = RAK WisBlock 4631
+custom_meshtastic_images = rak4631.svg, rak4631_case.svg
+custom_meshtastic_tags = RAK
+
 extends = nrf52840_base
 board = wiscore_rak4631
 board_level = pr

variants/nrf52840/rak4631_nomadstar_meteor_pro/platformio.ini

@@ -1,5 +1,14 @@
 ; NomadStar Meteor Pro based on RAK4631 with RGBW LED LP5562 support
 [env:rak4631_nomadstar_meteor_pro]
+custom_meshtastic_hw_model = 96
+custom_meshtastic_hw_model_slug = NOMADSTAR_METEOR_PRO
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = NomadStar Meteor Pro
+custom_meshtastic_images = meteor_pro.svg
+custom_meshtastic_tags = NomadStar
+
 extends = nrf52840_base
 board = wiscore_rak4631
 board_check = true

variants/nrf52840/rak_wismeshtag/platformio.ini

@@ -1,8 +1,17 @@
 ; The very slick RAK wireless RAK 4631 / 4630 board - Unified firmware for 5005/19003, with or without OLED RAK 1921
 [env:rak_wismeshtag]
+custom_meshtastic_support_level = 1
+custom_meshtastic_images = rak_wismesh_tag.svg
+custom_meshtastic_tags = RAK
+
 extends = nrf52840_base
 board = wiscore_rak4631
 board_check = true
+custom_meshtastic_hw_model = 105
+custom_meshtastic_hw_model_slug = WISMESH_TAG
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_display_name = RAK WisMesh Tag
+custom_meshtastic_actively_supported = true
 build_flags = ${nrf52840_base.build_flags}
   -I variants/nrf52840/rak_wismeshtag
   -D WISMESH_TAG

variants/nrf52840/rak_wismeshtap/platformio.ini

@@ -1,5 +1,14 @@
 ; The very slick RAK wireless RAK10701 Field Tester device.  Note you will have to flash to Arduino bootloader to use this firmware.  Be aware touch is not currently working.
 [env:rak_wismeshtap]
+custom_meshtastic_hw_model = 84
+custom_meshtastic_hw_model_slug = WISMESH_TAP
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = RAK WisMesh Tap
+custom_meshtastic_images = rak-wismeshtap.svg
+custom_meshtastic_tags = RAK
+
 extends = nrf52840_base
 board = wiscore_rak4631
 build_flags = ${nrf52840_base.build_flags}

variants/nrf52840/seeed_solar_node/platformio.ini

@@ -1,4 +1,13 @@
 [env:seeed_solar_node]
+custom_meshtastic_hw_model = 95
+custom_meshtastic_hw_model_slug = SEEED_SOLAR_NODE
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = Seeed SenseCAP Solar Node
+custom_meshtastic_images = seeed_solar.svg
+custom_meshtastic_tags = Seeed
+
 board = seeed_solar_node
 extends = nrf52840_base
 ;board_level = extra

variants/nrf52840/seeed_wio_tracker_L1/platformio.ini

@@ -1,4 +1,14 @@
 [env:seeed_wio_tracker_L1]
+custom_meshtastic_hw_model = 99
+custom_meshtastic_hw_model_slug = SEEED_WIO_TRACKER_L1
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = Seeed Wio Tracker L1
+custom_meshtastic_images = wio_tracker_l1_case.svg
+custom_meshtastic_tags = Seeed
+custom_meshtastic_requires_dfu = true
+
 board = seeed_wio_tracker_L1
 extends = nrf52840_base
 build_flags = ${nrf52840_base.build_flags} 

variants/nrf52840/seeed_wio_tracker_L1_eink/platformio.ini

@@ -1,4 +1,13 @@
 [env:seeed_wio_tracker_L1_eink]
+custom_meshtastic_hw_model = 100
+custom_meshtastic_hw_model_slug = SEEED_WIO_TRACKER_L1_EINK
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = Seeed Wio Tracker L1 E-Ink
+custom_meshtastic_images = wio_tracker_l1_eink.svg
+custom_meshtastic_tags = Seeed
+
 board = seeed_wio_tracker_L1
 extends = nrf52840_base
 ;board_level = extra

variants/nrf52840/seeed_xiao_nrf52840_kit/platformio.ini

@@ -1,5 +1,14 @@
 ; Seeed Xiao BLE: https://wiki.seeedstudio.com/XIAO_BLE/
 [env:seeed_xiao_nrf52840_kit]
+custom_meshtastic_hw_model = 88
+custom_meshtastic_hw_model_slug = XIAO_NRF52_KIT
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = Seeed Xiao NRF52840 Kit
+custom_meshtastic_images = seeed_xiao_nrf52_kit.svg
+custom_meshtastic_tags = Seeed
+
 extends = nrf52840_base
 board = xiao_ble_sense
 board_level = pr

variants/nrf52840/t-echo-lite/platformio.ini

@@ -1,5 +1,14 @@
 ; Using original screen class
 [env:t-echo-lite]
+custom_meshtastic_hw_model = 109
+custom_meshtastic_hw_model_slug = T_ECHO_LITE
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = false
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = LILYGO T-Echo Lite
+custom_meshtastic_images = techo_lite.svg
+custom_meshtastic_tags = LilyGo
+
 extends = nrf52840_base
 board = t-echo
 board_check = true

variants/nrf52840/t-echo/platformio.ini

@@ -1,5 +1,14 @@
 ; Using original screen class
 [env:t-echo]
+custom_meshtastic_hw_model = 7
+custom_meshtastic_hw_model_slug = T_ECHO
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 1
+custom_meshtastic_display_name = LILYGO T-Echo
+custom_meshtastic_images = t-echo.svg
+custom_meshtastic_tags = LilyGo
+
 extends = nrf52840_base
 board = t-echo
 board_level = pr

variants/nrf52840/tracker-t1000-e/platformio.ini

@@ -1,7 +1,16 @@
 [env:tracker-t1000-e]
+custom_meshtastic_support_level = 1
+custom_meshtastic_images = tracker-t1000-e.svg
+custom_meshtastic_tags = Seeed
+
 extends = nrf52840_base
 board = tracker-t1000-e
 board_level = pr
+custom_meshtastic_hw_model = 71
+custom_meshtastic_hw_model_slug = TRACKER_T1000_E
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_display_name = Seeed SenseCAP T1000-E
+custom_meshtastic_actively_supported = true
 build_flags = ${nrf52840_base.build_flags}
   -Ivariants/nrf52840/tracker-t1000-e
   -Isrc/platform/nrf52/softdevice

variants/nrf52840/wio-tracker-wm1110/platformio.ini

@@ -1,5 +1,15 @@
 ; The red tracker Dev Board with the WM1110 module
 [env:wio-tracker-wm1110]
+custom_meshtastic_hw_model = 21
+custom_meshtastic_hw_model_slug = WIO_WM1110
+custom_meshtastic_architecture = nrf52840
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = Seeed Wio WM1110 Tracker
+custom_meshtastic_images = wio-tracker-wm1110.svg
+custom_meshtastic_tags = Seeed
+custom_meshtastic_requires_dfu = true
+
 extends = nrf52840_base
 board = wio-tracker-wm1110
 build_flags = ${nrf52840_base.build_flags}

variants/rp2040/rak11310/platformio.ini

@@ -1,4 +1,14 @@
 [env:rak11310]
+custom_meshtastic_hw_model = 26
+custom_meshtastic_hw_model_slug = RAK11310
+custom_meshtastic_architecture = rp2040
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 2
+custom_meshtastic_display_name = RAK WisBlock 11310
+custom_meshtastic_images = rak11310.svg
+custom_meshtastic_tags = RAK
+custom_meshtastic_requires_dfu = true
+
 extends = rp2040_base
 board = rakwireless_rak11300
 board_level = pr

variants/rp2040/rp2040-lora/platformio.ini

@@ -1,4 +1,13 @@
 [env:rp2040-lora]
+custom_meshtastic_hw_model = 30
+custom_meshtastic_hw_model_slug = RP2040_LORA
+custom_meshtastic_architecture = rp2040
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 2
+custom_meshtastic_display_name = RP2040 LoRa
+custom_meshtastic_tags = Waveshare
+custom_meshtastic_requires_dfu = true
+
 extends = rp2040_base
 board = rpipico
 upload_protocol = picotool

variants/rp2040/rpipico/platformio.ini

@@ -1,4 +1,14 @@
 [env:pico]
+custom_meshtastic_hw_model = 47
+custom_meshtastic_hw_model_slug = RPI_PICO
+custom_meshtastic_architecture = rp2040
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = Raspberry Pi Pico
+custom_meshtastic_images = pico.svg
+custom_meshtastic_tags = RPi, DIY
+custom_meshtastic_requires_dfu = true
+
 extends = rp2040_base
 board = rpipico
 board_level = pr

variants/rp2040/rpipicow/platformio.ini

@@ -1,4 +1,14 @@
 [env:picow]
+custom_meshtastic_hw_model = 47
+custom_meshtastic_hw_model_slug = RPI_PICO
+custom_meshtastic_architecture = rp2040
+custom_meshtastic_actively_supported = true
+custom_meshtastic_support_level = 3
+custom_meshtastic_display_name = Raspberry Pi Pico W
+custom_meshtastic_images = rpipicow.svg
+custom_meshtastic_tags = RPi, DIY
+custom_meshtastic_requires_dfu = true
+
 extends = rp2040_base
 board = rpipicow
 board_level = pr