Move endif

Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>

src/modules/ExternalNotificationModule.cpp

@@ -168,7 +168,7 @@ int32_t ExternalNotificationModule::runOnce()
             delay = EXT_NOTIFICATION_FAST_THREAD_MS;
 #endif
 
-#if defined(T_WATCH_S3) || defined(T_LORA_PAGER)
+#ifdef T_WATCH_S3
             drv.go();
 #endif
         }
@@ -541,19 +541,6 @@ ProcessMessage ExternalNotificationModule::handleReceived(const meshtastic_MeshP
                     (!isBroadcast(mp.to) && isToUs(&mp))) {
                     // Buzz if buzzer mode is not in DIRECT_MSG_ONLY or is DM to us
                     isNagging = true;
-#ifdef T_LORA_PAGER
-                    if (canBuzz()) {
-                        drv.setWaveform(0, 16); // Long buzzer 100%
-                        drv.setWaveform(1, 0);  // Pause
-                        drv.setWaveform(2, 16);
-                        drv.setWaveform(3, 0);
-                        drv.setWaveform(4, 16);
-                        drv.setWaveform(5, 0);
-                        drv.setWaveform(6, 16);
-                        drv.setWaveform(7, 0);
-                        drv.go();
-                    }
-#endif
                     if (!moduleConfig.external_notification.use_pwm && !moduleConfig.external_notification.use_i2s_as_buzzer) {
                         setExternalState(2, true);
                     } else {

src/nimble/NimbleBluetooth.cpp

@@ -651,8 +651,8 @@ class NimbleBluetoothServerCallback : public NimBLEServerCallbacks
     {
         LOG_INFO("BLE incoming connection %s", connInfo.getAddress().toString().c_str());
 
-#if defined(CONFIG_IDF_TARGET_ESP32S3) || defined(CONFIG_IDF_TARGET_ESP32C6)
         const uint16_t connHandle = connInfo.getConnHandle();
+#if NIMBLE_ENABLE_2M_PHY && (defined(CONFIG_IDF_TARGET_ESP32S3) || defined(CONFIG_IDF_TARGET_ESP32C6))
         int phyResult =
             ble_gap_set_prefered_le_phy(connHandle, BLE_GAP_LE_PHY_2M_MASK, BLE_GAP_LE_PHY_2M_MASK, BLE_GAP_LE_PHY_CODED_ANY);
         if (phyResult == 0) {
@@ -660,6 +660,7 @@ class NimbleBluetoothServerCallback : public NimBLEServerCallbacks
         } else {
             LOG_WARN("Failed to prefer 2M PHY for conn %u, rc=%d", connHandle, phyResult);
         }
+#endif
 
         int dataLenResult = ble_gap_set_data_len(connHandle, kPreferredBleTxOctets, kPreferredBleTxTimeUs);
         if (dataLenResult == 0) {
@@ -670,9 +671,10 @@ class NimbleBluetoothServerCallback : public NimBLEServerCallbacks
 
         LOG_INFO("BLE conn %u initial MTU %u (target %u)", connHandle, connInfo.getMTU(), kPreferredBleMtu);
         pServer->updateConnParams(connHandle, 6, 12, 0, 200);
-#endif
     }
+#endif
 
+#ifdef NIMBLE_TWO
     virtual void onDisconnect(NimBLEServer *pServer, NimBLEConnInfo &connInfo, int reason)
     {
         LOG_INFO("BLE disconnect reason: %d", reason);
@@ -818,7 +820,7 @@ void NimbleBluetooth::setup()
     NimBLEDevice::init(getDeviceName());
     NimBLEDevice::setPower(ESP_PWR_LVL_P9);
 
-#if defined(CONFIG_IDF_TARGET_ESP32S3) || defined(CONFIG_IDF_TARGET_ESP32C6)
+#if NIMBLE_ENABLE_2M_PHY && (defined(CONFIG_IDF_TARGET_ESP32S3) || defined(CONFIG_IDF_TARGET_ESP32C6))
     int mtuResult = NimBLEDevice::setMTU(kPreferredBleMtu);
     if (mtuResult == 0) {
         LOG_INFO("BLE MTU request set to %u", kPreferredBleMtu);