* Add BaseUI support for L1 EInk
* Fix Eink offset
* Add joystick
* Updates
* Adjust Seeed Wio Tracker L1 E-Ink variant (#7326)
* Rename variant
Needs the -inkhud suffix to work correctly with the web flasher
* Display driver for ZJY122250_0213BAAMFGN
* Remove dead code from nicheGraphics.h
Remnants of T-Echo's nicheGraphics.h file, which was used as a template.
* Use ZJY122250_0213BAAMFGN driver
Improves display health. We don't need as many full refreshes now.
* Tidying
* board_check = true
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Consolidation
* Add hack for existing InkHUD button functionality
---------
Co-authored-by: todd-herbert <herbert.todd@gmail.com>
* Initial support for the ThinkNode M5
* Update variants/esp32s3/ELECROW-ThinkNode-M5/platformio.ini
Co-authored-by: Austin <vidplace7@gmail.com>
* Cleanup variant.h for Elecrow Thinknode M5
* Properly detect battery voltage
* Turn backlight off when screen sleeps
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Austin <vidplace7@gmail.com>
* add new platform rak_wismeshtag
* Remove RTC and Ethernet definitions from variant.h
* Remove unused EINK and Ethernet definitions from variant.h and platformio.ini
* Add WISMESH_TAG hardware model definition in architecture.h and update build flags in platformio.ini
* Remove unused build flags and dependencies
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: daniel <daniel.cao@rakwireless.com>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
* Enable GPS for Wio-E5 variant on Serial2
* Add ability to override GPS serial port using GPS_SERIAL_PORT, and make RAK2560 use it.
* Don't try to send ATAK packets if ATAK is disabled, +4k flash
* docs(xiao_ble): Simplify building and flashing instructions
- **Update Bootloader** - deleted this section, as Meshtastic now builds-in a compatible SoftDevice
- **PlatformIO Environment Preparation** - deleted this section, as Meshtastic now builds-in a compatible SoftDevice
- **Build Meshtastic** - simplified it greatly by referring to Meshtastic documentation
- **Flash the firmware to the Xiao BLE** - simplified it greatly as Meshtastic now builds firmware.uf2; added some observations for a succesful flash
Light cleanup of Markdown and renumbering of sections.
Signed-off-by: Andrew Yong <me@ndoo.sg>
* docs(xiao_ble): Replace some HTML with Markdown, cleanup Markdown
Signed-off-by: Andrew Yong <me@ndoo.sg>
* docs(xiao_ble): Update SX126X_TXEN definition location
Signed-off-by: Andrew Yong <me@ndoo.sg>
* docs(xiao_ble): Fresher information about E22 modules
Signed-off-by: Andrew Yong <me@ndoo.sg>
* docs(xiao_ble): Instructions for E22...M33S modules
Also re-order the Build section to come after the Wiring section since the build instructions require special attention if the wiring/modules differ from the variant's expected pins/module.
Signed-off-by: Andrew Yong <me@ndoo.sg>
* docs(xiao_ble): Rename all XIAO BLE to XIAO nRF52840
Signed-off-by: Andrew Yong <me@ndoo.sg>
* docs(xiao_ble): Remove note about Linux since shell script is gone
Signed-off-by: Andrew Yong <me@ndoo.sg>
* docs(xiao_ble): trunk fmt and fix links
Signed-off-by: Andrew Yong <me@ndoo.sg>
---------
Signed-off-by: Andrew Yong <me@ndoo.sg>
These DIY builds are functionally similar to the legacy xiao_ble variant, but use a pinout harmonized with the officially-supported XIAO nRF52840 & Wio-SX1262 Kit for Meshtastic (SKU 102010710).
An additional E22-900M33S variant is provided to ensure SX1262 transmit power is set below the maximum PA input for that module, to avoid damaging it.
- seeed_xiao_nrf52840_e22_900m30s:
- XIAO nRF52840 + EBYTE E22-900M30S
- EBYTE E22 pinout matching Wio-SX1262 (SKU 113010003)
- I2C
- SDA: D6
- SCL: D7
- User button: D0
- Gain is programmed in firmware - user Tx power setting is the desired final output power
- seeed_xiao_nrf52840_e22_900m33s:
- XIAO nRF52840 + EBYTE E22-900M33S
- EBYTE E22 pinout matching Wio-SX1262 (SKU 113010003)
- I2C
- SDA: D6
- SCL: D7
- User button: D0
- Gain is programmed in firmware - user Tx power setting is the desired final output power
Signed-off-by: Andrew Yong <me@ndoo.sg>
The link to the product should point to the vendor's website, not a random distributor.
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* Tests to identify display model
* (InkHUD) SSD1682 controller IC
Has a few quirks, gets its own base class
* (InkHUD) E0213A367 Display
For Heltec Wireless Paper V1.1.1, V1.2
For Heltec VM-E213 V1.1
* (InkHUD) Select display model at boot
* (BaseUI) Wrapper to combine multiple GxEPD2 drivers
Workaround for issue of GxEPD2_BW objects not having a shared base class. Allows us to select a driver at runtime.
https://github.com/meshtastic/firmware/issues/6851#issuecomment-2905353447
* (BaseUI) Select E-Ink model at boot
* (InkHUD) SSD1682 deep sleep
* (InkHUD) No deep sleep for SSD1682
* (InkHUD) Fully no-op deep sleep for SSD1682
