* Start portduino_config refactor
* refactor GPIOs to new portduino_config
* More portduino_config work
* More conversion to portduino_config
* Finish portduino_config transition
* trunk
* yaml output work
* Simplify the GPIO config
* Trunk
* Added compatibility between nodes on different Presets through `Mesh via UDP`
* Optimize multicast handling and channel mapping
- FloodingRouter: remove redundant UDP-encrypted rebroadcast suppression.
- Router: guard multicast fallback with HAS_UDP_MULTICAST and map fallback-decoded packets
to the local default channel via isDefaultChannel()
- UdpMulticastHandler: set transport_mechanism only after successful decode
* trunk fmt
* Move setting transport mechanism.
---------
Co-authored-by: GUVWAF <thijs@havinga.eu>
* Added compatibility between nodes on different Presets through `Mesh via UDP`
* Optimize multicast handling and channel mapping
- FloodingRouter: remove redundant UDP-encrypted rebroadcast suppression.
- Router: guard multicast fallback with HAS_UDP_MULTICAST and map fallback-decoded packets
to the local default channel via isDefaultChannel()
- UdpMulticastHandler: set transport_mechanism only after successful decode
* trunk fmt
* Move setting transport mechanism.
---------
Co-authored-by: GUVWAF <thijs@havinga.eu>
* Make phone queues use a static pointer queue
* Static init
* Compile time constants now
* Instead, lets just use the normal pointerqueue for linux native builds and static for IoT platforms
* Add missing method
* Missing methods
* Update variant.h
Meshtastic no longer fits on the flash of the Picomputer.
Since this is a handheld, portable device, it's unlikely that people are
connecting to it via the webserver. So, disable the webserver and it fits
again:
```
Checking size .pio/build/picomputer-s3-tft/firmware.elf
Advanced Memory Usage is available via "PlatformIO Home > Project Inspect"
RAM: [=== ] 32.4% (used 106056 bytes from 327680 bytes)
Flash: [==========] 99.1% (used 3313913 bytes from 3342336 bytes)
```
Fixes: https://github.com/meshtastic/firmware/issues/7906
* Add initial variant and platformio configuration for RAK WISMESHTAP V2
* Add initial variant and platformio configuration for rak wismesh tap v2
* Remove unnecessary Meshtastic build flags from rak_wismesh_tap_v2 configuration
* Enable LGFX button support in rak_wismesh_tap_v2 configuration
* Revert "Enable LGFX button support in rak_wismesh_tap_v2 configuration"
This reverts commit 2bd2c1a03b.
---------
Co-authored-by: Daniel.Cao <daniel.cao@rakwireless.com>
* Start portduino_config refactor
* refactor GPIOs to new portduino_config
* More portduino_config work
* More conversion to portduino_config
* Finish portduino_config transition
* trunk
* yaml output work
* Simplify the GPIO config
* Trunk
* Add initial variant and platformio configuration for RAK WISMESHTAP V2
* Add initial variant and platformio configuration for rak wismesh tap v2
* Remove unnecessary Meshtastic build flags from rak_wismesh_tap_v2 configuration
* Enable LGFX button support in rak_wismesh_tap_v2 configuration
* Revert "Enable LGFX button support in rak_wismesh_tap_v2 configuration"
This reverts commit 2bd2c1a03b.
---------
Co-authored-by: Daniel.Cao <daniel.cao@rakwireless.com>
* Show ExternalNotification as excluded if it is
* Enable ExternalNotification, SerialModule and RangeTest on STM32WL
* Misc fixes for #7797 - ARCH_STM32 -> ARCH_STM32WL, use less flash by dropping weather station support for serialmodule, set tx/rx pins before begin
* Enable Serial1 on RAK3172, make SerialModule use it (console is on LPUART1)
* Fix SerialModule on RAK3172, fix board definition of RAK3172 to include the right pin mapping.
* Show ExternalNotification as excluded if it is
* Enable ExternalNotification, SerialModule and RangeTest on STM32WL
* Misc fixes for #7797 - ARCH_STM32 -> ARCH_STM32WL, use less flash by dropping weather station support for serialmodule, set tx/rx pins before begin
* Enable Serial1 on RAK3172, make SerialModule use it (console is on LPUART1)
* Fix SerialModule on RAK3172, fix board definition of RAK3172 to include the right pin mapping.
* Hold for >20s after GPS lock
GPS chips are designed to stay locked for a while to download some data and save it.
This data is important for speeding up future locks, and making them higher quality.
Our present configuration could make every lock perform similar to first lock.
This patch sets a hold of between 20s and 10% of the lock search time after lock
is acquired. This should allow the GPS to finish its work before we turn it off.
Fixes https://github.com/meshtastic/firmware/issues/7466
* Remove T1000E-specific GPS holds
The new code does the same thing, for all devices.
* Fix publishing settings
* Cleanups, removing unused variables.
* ifdef log line with GPS_DEBUG
* fixQual is not a bool.
* Hold for >20s after GPS lock
GPS chips are designed to stay locked for a while to download some data and save it.
This data is important for speeding up future locks, and making them higher quality.
Our present configuration could make every lock perform similar to first lock.
This patch sets a hold of between 20s and 10% of the lock search time after lock
is acquired. This should allow the GPS to finish its work before we turn it off.
Fixes https://github.com/meshtastic/firmware/issues/7466
* Remove T1000E-specific GPS holds
The new code does the same thing, for all devices.
* Fix publishing settings
* Cleanups, removing unused variables.
* ifdef log line with GPS_DEBUG
* fixQual is not a bool.
