* Start portduino_config refactor
* refactor GPIOs to new portduino_config
* More portduino_config work
* More conversion to portduino_config
* Finish portduino_config transition
* trunk
* yaml output work
* Simplify the GPIO config
* Trunk
* Start portduino_config refactor
* refactor GPIOs to new portduino_config
* More portduino_config work
* More conversion to portduino_config
* Finish portduino_config transition
* trunk
* yaml output work
* Simplify the GPIO config
* Trunk
* Pro-Micro DeepSleep Quick Fix
It is noticed that some nRF52840 boards (pro-micro in particular)
stopped waking up from the deep sleep state (shutdown state)
with a press of a button.
The problem is in a Serial1.end() call.
* Clear GPREGRET before setting
There are some troubles with that register:
it is recommended to clear it with 0xFF mask
and only after that perform a setting.
* Pro-Micro button SENSE signal
Added SENSE signal on the user button.
It is explicitly enabled now for this platform.
* nRF52 pre-sleep main serial check
Added another usage check for the main Serial.
It could save some nerves in case the port is not in use by any means.
Applied trunk fmt to the file.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Initial support for the ThinkNode M5
* Update variants/esp32s3/ELECROW-ThinkNode-M5/platformio.ini
Co-authored-by: Austin <vidplace7@gmail.com>
* Cleanup variant.h for Elecrow Thinknode M5
* Properly detect battery voltage
* Turn backlight off when screen sleeps
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Austin <vidplace7@gmail.com>
* treewide: make 'ifdef DEBUG_PORT' guards also take into account DEBUG_MUTE
* stm32wl: Add a guard against having debug prints turned on without PIO_FRAMEWORK_ARDUINO_NANOLIB_FLOAT_PRINTF defined
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* add new platform rak_wismeshtag
* Remove RTC and Ethernet definitions from variant.h
* Remove unused EINK and Ethernet definitions from variant.h and platformio.ini
* Add WISMESH_TAG hardware model definition in architecture.h and update build flags in platformio.ini
* Remove unused build flags and dependencies
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: daniel <daniel.cao@rakwireless.com>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
* Add support for RAK3112 variant with necessary configurations and definitions
* Add the configuration of the LED pin
* Refactor rak3112 variant configuration: update name, remove unused files,
* Update RAK3112 configuration: refine memory settings, adjust GPS pin definitions
* Update RAK3112 hardware vendor definition to use correct model
* configure LED pins and update module definitions
* Update USB mode configuration for RAK3112 board
* Update power and battery configuration in rak3112 variant
* Cancel the modification of mesh.pb.h
* Rename RAKwireless RAK3112 to RAK3312
---------
Co-authored-by: daniel <daniel.cao@rakwireless.com>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Update platformio inis for stm32 platform and wio-e5 variant for enabling i2c
* Don't reference timezone functions if MESHTASTIC_EXCLUDE_TZ is defined
* Use custom pow_of_two in RadioInterface instead of floating-point pow()
* First pass: enable sensors for STM32wL
* Fix AirQualityTelemetryModule being created if the PM25AQI header is missing
* Link in power sensor libraries
* more ini tweaks
* Add =1 to EXCLUDE defines, fix indentation.
* Drop HAS_WIRE in ini, it's defined in architecture.h
* Fix build when power sensor libraries are missing
Make MAX sensor integration into Power.cpp optional based on its library header existing.
Also make NullSensor expose a voltage and current sensor, because Power calls directly into these for INA sensors.
This lets us remove all the deps for the STM32WL platform.
* Change default I2C for RAK3172 to be I2C1, not I2C2
* Respect the laws of mathematics (oops)
