* Introduce non-linear TX_GAIN_LORA
Previously, our TX_GAIN_LORA setting was a single number, intended
to represent the signal gain going through a power amp (plus or minus
antenna, attenuator, and other parts of the RF chain).
It turns out the relationship between the input power (i.e. from an SX1262)
and total output power is often non-linear. While we fudged a 1dBm difference
here and there with existing chips, the Heltec v4 has a 5dBm difference in gain
depending on which end of the input power (and frequency) you are at.
To allow people to run their Heltec v4 at max power when legal, and future
proof our code, this patch introduced an optional array-based TX_GAIN_LORA.
Define NUM_PA_POINTS and set TX_GAIN_LORA to gain values for a given input
power in 1dBm increments, and all will work.
For linear systems, just continue to define TX_GAIN_LORA as a number.
Fixes https://github.com/meshtastic/firmware/issues/8070
* Remove temporary power limit on heltec v4
* Add function RadioLibInterface::checkOutputPower
* Ensure SX126x reaches minimum supported power.
* Keep it simple, instead.
* Added compatibility between nodes on different Presets through `Mesh via UDP`
* Optimize multicast handling and channel mapping
- FloodingRouter: remove redundant UDP-encrypted rebroadcast suppression.
- Router: guard multicast fallback with HAS_UDP_MULTICAST and map fallback-decoded packets
to the local default channel via isDefaultChannel()
- UdpMulticastHandler: set transport_mechanism only after successful decode
* trunk fmt
* Move setting transport mechanism.
---------
Co-authored-by: GUVWAF <thijs@havinga.eu>
* Added compatibility between nodes on different Presets through `Mesh via UDP`
* Optimize multicast handling and channel mapping
- FloodingRouter: remove redundant UDP-encrypted rebroadcast suppression.
- Router: guard multicast fallback with HAS_UDP_MULTICAST and map fallback-decoded packets
to the local default channel via isDefaultChannel()
- UdpMulticastHandler: set transport_mechanism only after successful decode
* trunk fmt
* Move setting transport mechanism.
---------
Co-authored-by: GUVWAF <thijs@havinga.eu>
Meshtastic no longer fits on the flash of the Picomputer.
Since this is a handheld, portable device, it's unlikely that people are
connecting to it via the webserver. So, disable the webserver and it fits
again:
```
Checking size .pio/build/picomputer-s3-tft/firmware.elf
Advanced Memory Usage is available via "PlatformIO Home > Project Inspect"
RAM: [=== ] 32.4% (used 106056 bytes from 327680 bytes)
Flash: [==========] 99.1% (used 3313913 bytes from 3342336 bytes)
```
Fixes: https://github.com/meshtastic/firmware/issues/7906
* Add initial variant and platformio configuration for RAK WISMESHTAP V2
* Add initial variant and platformio configuration for rak wismesh tap v2
* Remove unnecessary Meshtastic build flags from rak_wismesh_tap_v2 configuration
* Enable LGFX button support in rak_wismesh_tap_v2 configuration
* Revert "Enable LGFX button support in rak_wismesh_tap_v2 configuration"
This reverts commit 2bd2c1a03b.
---------
Co-authored-by: Daniel.Cao <daniel.cao@rakwireless.com>
* Add initial variant and platformio configuration for RAK WISMESHTAP V2
* Add initial variant and platformio configuration for rak wismesh tap v2
* Remove unnecessary Meshtastic build flags from rak_wismesh_tap_v2 configuration
* Enable LGFX button support in rak_wismesh_tap_v2 configuration
* Revert "Enable LGFX button support in rak_wismesh_tap_v2 configuration"
This reverts commit 2bd2c1a03b.
---------
Co-authored-by: Daniel.Cao <daniel.cao@rakwireless.com>
* Initial support for the ThinkNode M5
* Update variants/esp32s3/ELECROW-ThinkNode-M5/platformio.ini
Co-authored-by: Austin <vidplace7@gmail.com>
* Cleanup variant.h for Elecrow Thinknode M5
* Properly detect battery voltage
* Turn backlight off when screen sleeps
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Austin <vidplace7@gmail.com>
