* Show ExternalNotification as excluded if it is
* Enable ExternalNotification, SerialModule and RangeTest on STM32WL
* Misc fixes for #7797 - ARCH_STM32 -> ARCH_STM32WL, use less flash by dropping weather station support for serialmodule, set tx/rx pins before begin
* Enable Serial1 on RAK3172, make SerialModule use it (console is on LPUART1)
* Fix SerialModule on RAK3172, fix board definition of RAK3172 to include the right pin mapping.
* Add support for RAK3112 variant with necessary configurations and definitions
* Add the configuration of the LED pin
* Refactor rak3112 variant configuration: update name, remove unused files,
* Update RAK3112 configuration: refine memory settings, adjust GPS pin definitions
* Update RAK3112 hardware vendor definition to use correct model
* configure LED pins and update module definitions
* Update USB mode configuration for RAK3112 board
* Update power and battery configuration in rak3112 variant
* Cancel the modification of mesh.pb.h
* Rename RAKwireless RAK3112 to RAK3312
---------
Co-authored-by: daniel <daniel.cao@rakwireless.com>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* add support for GAT562 Mesh Trial Tracker
* Hardware Model Definition for GAT562_MESH_TRIAL_TRACKER
* Added RAK4630 for led pin 2 (blue)
* Added RAK4630 for led pin 2 (blue) comment
* don't touch src/mesh/NodeDB.cpp
* set fixed baudrate for gat562_mesh_trial_tracker
* adjust the order of the HW_VENDOR defines
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* Add support for MeshLink
* Updated, enabled watchdog and added button definition
* added eink variant and removed some compile errors
* Small board json file edit
* Finally got trunk working (somehow?), this is just cleanup with trunk fmt
* Various improvements and cleanup. Removed the use of PIN_3V3_En and defined a specific WD_EN pin instead for better clarity. Will do a bit more testing asap to make sure everything still works as intended :)
* Enable on-board QSPI Flash
* run trunk fmt with clang-format
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Austin <vidplace7@gmail.com>
* update indicator board
* Fixed the issue that indicator device uploads via rp2040 serial port in some cases.
* esp debug logs
* USB mode=1 messed up the debug log
* dummy for config transfer (#5154)
---------
Co-authored-by: mverch67 <manuel.verch@gmx.de>
Co-authored-by: virgil <virgil.wang.cj@gmail.com>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
In 2020, geeksville had a NRF52840-dk development board with a
busted oscilliator. Let's retire it from service :)
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
The lora-relay boards were important pathfinders for nrf52
support some years back. They are no longer commonly produced and
there are now many nrf52 options on the market. Retire these
boards and associated variant.
* Fix I2C pindefs
* Initial driver testing for HT-VME290
* E-Ink full refresh after canned message pop up
* Tidy variant folders
* Clean ESP32 cpuDeepSleep method
Merge sections, and remove the random assortment of gpio holds left behind.
* Enable 32kHz in variant.h
* Orient E290 with LoRa antenna facing up
* Revert "Clean ESP32 cpuDeepSleep method"
This reverts commit cb8ee508ec2d6bc27a8e228021fd1efbd034c4a0.
* Reduce deep-sleep current for VME213 (non-intrusive)
Originally I made an attempt at tidying up the cpuDeepSleep method, but have reverted that. New commit makes only the changes needed to support VME213. Don't really want the headache of breaking sleep for other variants, especially when this PR is just about implementing new boards.
* Update lib_deps; remove board_level extra
* Make STM compile again and update toolchain. The binary is too big for the flash. WIP
* Making progress with OSFS, still WIP
* more progress, still too big. Adding RAK3172 to the equasion
* Make STM compile again and update toolchain. The binary is too big for the flash. WIP
* Making progress with OSFS, still WIP
* more progress, still too big. Adding RAK3172 to the equasion
* still too big
* minimize build
* trunk fmt
* fix a couple of symbol clashes
* trunk fmt
* down to 101% with a release vs. debug build and omitting the flash strings
* fix compilation
* fix compilation once more
* update protobufs linkage
* - Toolchain updated
- Fixed macro error
* silence compiler warning
note: do something about this assert...
* new toolkit and fix Power.cpp
* STM32WL make it fit (#4330)
* Add option to exclude I2C parts
The I2C hals and related code uses a significant amount of flash space and aren't required for a basic node.
* Add option to disable Admin and NodeInfo modules
Disabled by default in minimal build. This saves a significant amount of flash
* Disable unused hals
These use up significant flash
* Add float support for printf for debugging
Makes serial look nice for debugging
* This breaks my build for some reason
* These build flags can save a bit of flash
* Don't disable NodeInfo and Admin modules in minimal build
They fit in flash
* Don't include printf float support by default
Only useful for debugging
---------
Co-authored-by: Adam Lawson <dev@goshawk22.uk>
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Adam Lawson <dev@goshawk22.uk>
