Remove lib_deps section for all PlatformIO envs which are unneeded (only references the `extends` lib_deps, thus pointless)
This makes the configs more concise and make future PIO variants/ libdeps audits easier.
We set the buffer size to about a byte on NRF52480, less than
other platforms:
esp32.ini: -DSERIAL_BUFFER_SIZE=4096
esp32c6.ini: -DSERIAL_BUFFER_SIZE=4096
nrf52.ini: -DSERIAL_BUFFER_SIZE=1024
However, 115200 baud, like the T1000e uses is about 12 times that
- almost 15 bytes per millisecond.
15 bytes * 200 millisecond (our GPS poll rate) = 3000 bytes, which is longer than our buffer
on the nrf52 platform. This causes "GPS Buffer full" errors on the T1000e
and other devices based on NRF52480 with newer GPS chips.
This patch increases SERIAL_BUFFER_SIZE for nrf52480 to 4096 to align with
other platforms. It keeps the original 1024 for the nrf52832, which has
fewer resources.
Fixes https://github.com/meshtastic/firmware/issues/5767
* Improve NRF52 bluetooth power efficiency
* test T114 bad LFXO
* T1000 test
* force BLE param negotiation
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add mesh/Default.h include.
* Reflacter OnScreenKeyBoard Module, do not interrupt keyboard when new message comes.
* feat: Add long press scrolling for Joystick and upDown Encoder on baseUI frames and menus.
* refactor: Clean up code formatting and improve readability in Screen and OnScreenKeyboardModule
* Fix navigation on UpDownEncoder, default was RotaryEncoder while bringing the T_LORA_PAGER
* Update src/graphics/draw/MenuHandler.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/modules/OnScreenKeyboardModule.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/graphics/draw/NotificationRenderer.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Optimize the detection logic for repeated events of the arrow keys.
* Fixed parameter names in the OnScreenKeyboardModule::start
* Trunk fix
* Reflator OnScreenKeyboard Input checking, make it simple
* Simplify long press logic in OnScreenKeyboardModule.
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* changes of variants/nrf52840/nrf52.ini and variants/nrf52840/rak4631/platformio.ini
* try for nrf52 size reduction, faketec exclude unused radios and meshlink refactor
* can't exclude LR11X0 as in schematic there's option for LR1121
* remove -Map flag and -Wl
* removed spaces causing error
---------
Co-authored-by: macvenez <macvenez@gmail.com>
* Delete variants/nrf52840/diy/nrf52_promicro_diy_tcxo/Schematic_Pro-Micro_Pinouts.pdf
remove old file
* Add updated schematic
* Update GPS TX and RX pin definitions after swap
* Update GPS pin definitions and schematic link
Updated the schematic link to reflect GPS pin definition changes.
* Plain RAK4631 should not compile EInk and TFT display code
* Add USE_TFTDISPLAY to variant files.
* Derp
* Undo the platformio.ini changes to heltec_v4
* Drop unneeded src_filter lines
---------
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Jason P <applewiz@mac.com>
* Flags and scripts for size reduction on NRF52 -> Currently targeting rak4631
* Changes from the other branch poluted it
* Remove the stripper
* No strip
* Swap the GPS serial port pins.
* Trunk fixes
---------
Co-authored-by: Jason P <applewiz@mac.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Added OCV_ARRAY from measured discharge curve testing and update ADC multiplier
The ADC resistor divider ratio is 0.6 -> multiplier should be 1/0.6 ~=1.667
We data logged a full discharge curve at constant 100mA draw over 15hours to get a realistic voltage curve for battery SoC measurements.
* Remove power.h in favor of variant.h
---------
Co-authored-by: Jason P <applewiz@mac.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
