* Optimise GPS Baud Rate cycle
Previously, our baud rate cycled through one list twice.
There were some rarer baudrates in there, so this code
separates out those into a dedicated list that is only
run through if detection fails for common bauds. We also
only run through each baud rate once.
* Fix first time around bug
Would have always reset GPS baudrate every time.
* Add support for fixing GPS_BAUDRATE
If GPS_BAUDRATE is set in variant.h, the deployer knows something we
don't about the GPS. Used especially when the GPS is soldered to a board
in a commercial product :) If we see that, we don't try other baud rates
at all.
* Don't print blank lines in GPS_DEBUG.
* Try GPS_BAUDRATE first, not only.
* Fix spelling mistakes in comments
* Only use GPS_BAUDRATE if specified in variant.h
* Modify RareSerial Speeds based on FIXED or not.
* Remove assert in mesh-pb-constants.cpp
* Add raw packet output to portduino trace logging.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
We currently have 4 different places where we have the logic for
modifying LED state of the various types of Ambient LEDs,
ExternalNotificationModule::SetExternalOff
ExternalNotificationModule::SetExternalOn
AmbientLightingThread::setLighting
AmbientLightingThread::setLightingOff
This patch de-duplicates the methods in ExternalNotification to
a single method, using a boolean to toggle whether we're turning
things on or off.
* Add support for loading yaml from a config directory
* Add waveshare hats to the new config.d approach
* Move to available.d for module inactive module configs
* Update GPSUpdateScheduling.cpp
Default value is too short, resulting in unstable GPS locks on T1000-E (possibly others). Fix has been tested an confirmed working with no adverse effects, by multiple users. Also discussed at length on Discord
* Coerce minimum instead of hardcode
* config
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* T1000-E Peripherals
- enable intelligent charge controller signals
- enable Accelerometer
- enable internal I2C bus
- provide Power to Accelerometer
* POC Accelerometer Code (wakeScreen is moot for that device, just test if the driver works)
* fix building without the sensor
Implements an input driver utilising the MPR121 Touch IC and is compatible with common MPR121 keypad PCB's.
- Implements a "candybar" phone style 12-key keypad
- multiple taps to rotate through the character set
- longpress for navigation keys
- keymap to allow arbitrary routing of MPR121 pin to button configuration
- extendable to other key functions
- Integrates with the existing kbI2cBase implementation
- Works with CannedMessageModule Freetext mode
- Can be used with common MPR121 boards, such as https://www.amazon.com/MPR121-Capacitive-Keyboard-Buttons-Sensitive/dp/B083R89CHB/ref=sr_1_6
- Of use for PCB based radios, where some form of low surface area low component freetext input is required, but also without consuming too many IO pins.
- Tested on a T3S3 connected to Wire1 (Second) interface.
- Demonstration of functionality: https://youtu.be/UI6QP6nGvhY
After the recent change to move logging line breaks to a central
location, GPS_DEBUG is now emitting one character per line,
making the logs unusable.
Patch uses local strings and appends to collate and then print
in the right places.
Fixes https://github.com/meshtastic/firmware/issues/5099
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Triple Press on buttons toggles GPS enable/disable.
This enhancement plays a triple-beep so that users of devices with buzzers can get audible feedback about whether they have turned the GPS off or on. This is especially valuable for screenless devices such as the T1000E where it may not be immediately obvious the GPS has been disabled.
Determines if the given IP address is a private address, i.e. not routable on the public internet.
These are the ranges: 127.0.0.1, 10.0.0.0-10.255.255.255, 172.16.0.0-172.31.255.255, 192.168.0.0-192.168.255.255.
If so, allow MQTT publication the same as existing localhost support.
