* Swap the GPS serial port pins.
* Trunk fixes
---------
Co-authored-by: Jason P <applewiz@mac.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Added OCV_ARRAY from measured discharge curve testing and update ADC multiplier
The ADC resistor divider ratio is 0.6 -> multiplier should be 1/0.6 ~=1.667
We data logged a full discharge curve at constant 100mA draw over 15hours to get a realistic voltage curve for battery SoC measurements.
* Remove power.h in favor of variant.h
---------
Co-authored-by: Jason P <applewiz@mac.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* Make RAK4631 nodes power back on deep sleep
The devices will hang if the VBAT goes under 1.7V (Brown-out reset) and
they will never come back unless power supply goes completely off.
This kills unattended nodes.
Using the SystemOff the LPCOMP we can get the nodes back again when
power comes back, even if VBAT goes under 1.7V, which moreover is more
unlikely because the device is off.
* Adding support for heltec t114
And moved particularities to variant.h
* Remove old cpp comment that belongs to variant.h
It was a leftover.
* Trunk fix
---------
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* Update to Pro-micro variants
Schematic updated
Xtal variant removed
Extra module added to list
Extra explanation added to readme.
* Fix markdown formatting in readme.md
* Fix formatting in readme.md for RF switch section
---------
Co-authored-by: Tom <116762865+Nestpebble@users.noreply.github.com>
* Hold for >20s after GPS lock
GPS chips are designed to stay locked for a while to download some data and save it.
This data is important for speeding up future locks, and making them higher quality.
Our present configuration could make every lock perform similar to first lock.
This patch sets a hold of between 20s and 10% of the lock search time after lock
is acquired. This should allow the GPS to finish its work before we turn it off.
Fixes https://github.com/meshtastic/firmware/issues/7466
* Remove T1000E-specific GPS holds
The new code does the same thing, for all devices.
* Fix publishing settings
* Cleanups, removing unused variables.
* ifdef log line with GPS_DEBUG
* fixQual is not a bool.
* Hold for >20s after GPS lock
GPS chips are designed to stay locked for a while to download some data and save it.
This data is important for speeding up future locks, and making them higher quality.
Our present configuration could make every lock perform similar to first lock.
This patch sets a hold of between 20s and 10% of the lock search time after lock
is acquired. This should allow the GPS to finish its work before we turn it off.
Fixes https://github.com/meshtastic/firmware/issues/7466
* Remove T1000E-specific GPS holds
The new code does the same thing, for all devices.
* Fix publishing settings
* Cleanups, removing unused variables.
* ifdef log line with GPS_DEBUG
* fixQual is not a bool.
* Add BaseUI support for L1 EInk
* Fix Eink offset
* Add joystick
* Updates
* Adjust Seeed Wio Tracker L1 E-Ink variant (#7326)
* Rename variant
Needs the -inkhud suffix to work correctly with the web flasher
* Display driver for ZJY122250_0213BAAMFGN
* Remove dead code from nicheGraphics.h
Remnants of T-Echo's nicheGraphics.h file, which was used as a template.
* Use ZJY122250_0213BAAMFGN driver
Improves display health. We don't need as many full refreshes now.
* Tidying
* board_check = true
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Consolidation
* Add hack for existing InkHUD button functionality
---------
Co-authored-by: todd-herbert <herbert.todd@gmail.com>
