* Improve NRF52 bluetooth power efficiency
* test T114 bad LFXO
* T1000 test
* force BLE param negotiation
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add mesh/Default.h include.
* Reflacter OnScreenKeyBoard Module, do not interrupt keyboard when new message comes.
* feat: Add long press scrolling for Joystick and upDown Encoder on baseUI frames and menus.
* refactor: Clean up code formatting and improve readability in Screen and OnScreenKeyboardModule
* Fix navigation on UpDownEncoder, default was RotaryEncoder while bringing the T_LORA_PAGER
* Update src/graphics/draw/MenuHandler.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/modules/OnScreenKeyboardModule.h
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Update src/graphics/draw/NotificationRenderer.cpp
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* Optimize the detection logic for repeated events of the arrow keys.
* Fixed parameter names in the OnScreenKeyboardModule::start
* Trunk fix
* Reflator OnScreenKeyboard Input checking, make it simple
* Simplify long press logic in OnScreenKeyboardModule.
---------
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
* changes of variants/nrf52840/nrf52.ini and variants/nrf52840/rak4631/platformio.ini
* try for nrf52 size reduction, faketec exclude unused radios and meshlink refactor
* can't exclude LR11X0 as in schematic there's option for LR1121
* remove -Map flag and -Wl
* removed spaces causing error
---------
Co-authored-by: macvenez <macvenez@gmail.com>
* Delete variants/nrf52840/diy/nrf52_promicro_diy_tcxo/Schematic_Pro-Micro_Pinouts.pdf
remove old file
* Add updated schematic
* Update GPS TX and RX pin definitions after swap
* Update GPS pin definitions and schematic link
Updated the schematic link to reflect GPS pin definition changes.
* Plain RAK4631 should not compile EInk and TFT display code
* Add USE_TFTDISPLAY to variant files.
* Derp
* Undo the platformio.ini changes to heltec_v4
* Drop unneeded src_filter lines
---------
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Jason P <applewiz@mac.com>
* Flags and scripts for size reduction on NRF52 -> Currently targeting rak4631
* Changes from the other branch poluted it
* Remove the stripper
* No strip
* Swap the GPS serial port pins.
* Trunk fixes
---------
Co-authored-by: Jason P <applewiz@mac.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Added OCV_ARRAY from measured discharge curve testing and update ADC multiplier
The ADC resistor divider ratio is 0.6 -> multiplier should be 1/0.6 ~=1.667
We data logged a full discharge curve at constant 100mA draw over 15hours to get a realistic voltage curve for battery SoC measurements.
* Remove power.h in favor of variant.h
---------
Co-authored-by: Jason P <applewiz@mac.com>
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* Make RAK4631 nodes power back on deep sleep
The devices will hang if the VBAT goes under 1.7V (Brown-out reset) and
they will never come back unless power supply goes completely off.
This kills unattended nodes.
Using the SystemOff the LPCOMP we can get the nodes back again when
power comes back, even if VBAT goes under 1.7V, which moreover is more
unlikely because the device is off.
* Adding support for heltec t114
And moved particularities to variant.h
* Remove old cpp comment that belongs to variant.h
It was a leftover.
* Trunk fix
---------
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* Update to Pro-micro variants
Schematic updated
Xtal variant removed
Extra module added to list
Extra explanation added to readme.
* Fix markdown formatting in readme.md
* Fix formatting in readme.md for RF switch section
---------
Co-authored-by: Tom <116762865+Nestpebble@users.noreply.github.com>
