* add readme and update rfswitch
* Updated readme to include all data from Ebyte
* Added results from switch testing & notes thereon
* fixed picture
* Whoops!
Forgot to uncomment some settings from test.
* Update readme.md
* Delete variants/diy/nrf52_promicro_diy_tcxo/E80_RSSI_per_case.png
* Add webp image to appease trunk
* Update readme.md
* Trunky trunk trunk
* Clang and the trunk is done
* * Update RAK9154 sensor to tx remote power telemetry
* remove uf2 script, pio run does that inline
* move sensor module to correct position
* disable LED and Accelerometer code on rak2560
* trunk fmt
* mention epaper variant
* attention, revert, revert
* Enable Environment Telemetry of these values
* fix float values
* [WIP] Attempt upgrade to LovyanGFX 1.1.16
This is the version most used by the TFT branch.
I wonder if this will work with our existing code? :)
* Update Portduino to LovyanGFX 1.20.0
Manuel says it's good to go.
* Update unPhone platformio.ini
---------
Co-authored-by: Manuel <71137295+mverch67@users.noreply.github.com>
* I only have the V2.1 version, not sure if
the HW is same with V1, or V2. Given the few
resources I could find I think it is.
* ADC / Battery measure and TX/RX are working
* add more locking for shared SPI devices (#5595)
* add more locking for shared SPI devices
* call initSPI before the lock is used
* remove old one
* don't double lock
* Add missing unlock
* More missing unlocks
* Add locks to SafeFile, remove from `readcb`, introduce some LockGuards
* fix lock in setupSDCard()
* pull radiolib trunk with SPI-CS fixes
* change ContentHandler to Constructor type locks, where applicable
---------
Co-authored-by: mverch67 <manuel.verch@gmx.de>
Co-authored-by: GUVWAF <thijs@havinga.eu>
Co-authored-by: Manuel <71137295+mverch67@users.noreply.github.com>
* mesh-tab: lower I2C touch frequency
---------
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: mverch67 <manuel.verch@gmx.de>
Co-authored-by: GUVWAF <thijs@havinga.eu>
Co-authored-by: Manuel <71137295+mverch67@users.noreply.github.com>
Selection of minor edits from the TFT branch that are too
challenging to cherry-pick cleanly, including:
* introducing the HAS_TFT flag
* fixing pins in unphone
* Adding pinterdevice to portduino settings
* Added support for the LR1121 radio
Added support for the LR1121 radio, tested as functional with an E80-900M2213S from CDEbyte.
* Swap PNG for PDF
* remove PNG
* put TCXO voltage to 1.8, as in example file
It worked at 1.6v, but ¯\_(ツ)_/¯
* Hopefully this will appease Trunk
* Update rf switch pins and Schematic
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
- Support TLORA_V3.0. Update of the legendary 2.1_1.6.1 with solar charger, TCXO and IPEX connector.
- 'extra' some short-lived EOL intermediate boards in that range. If possible use T3S3 instead of all of these!
- update trunk to latest version
Unset BUTTON_PIN and BUTTON_NEED_PULLUP as the board ships without a user button.
Devices and users expecting a button on GPIO12 have to set [GPIO for user button](https://meshtastic.org/docs/configuration/radio/device/#gpio-for-user-button) to 12 (or any GPIO pin the momentary switch was connected to) to restore functionality.
Signed-off-by: Andrew Yong <me@ndoo.sg>
* add canned message and keyboard in indicator board
* Added virtual keyboard macro and enabled for Indicator
* Cleanup macros by applying USE_VIRTUAL_KEYBOARD and DISPLAY_CLOCK_FRAME
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
