we now hopefully apply the same radio settings as we did for the RF95

src/rf95/RadioLibInterface.h

@@ -7,12 +7,16 @@
 class RadioLibInterface : public RadioInterface
 {
   protected:
-    float freq = 915.0; // FIXME, init all these params from suer setings
     float bw = 125;
     uint8_t sf = 9;
     uint8_t cr = 7;
-    uint8_t syncWord = 0; // FIXME, use a meshtastic sync word, but hashed with the Channel name
-    int8_t power = 17;
+
+    /**
+     * FIXME, use a meshtastic sync word, but hashed with the Channel name.  Currently picking the same default
+     * the RF95 used (0x14). Note: do not use 0x34 - that is reserved for lorawan
+     */
+    uint8_t syncWord = SX126X_SYNC_WORD_PRIVATE;
+
     float currentLimit = 100; // FIXME
     uint16_t preambleLength = 8;
 
@@ -24,9 +28,8 @@ class RadioLibInterface : public RadioInterface
     PhysicalLayer &iface;
 
   public:
-    RadioLibInterface(RADIOLIB_PIN_TYPE cs, RADIOLIB_PIN_TYPE irq, RADIOLIB_PIN_TYPE rst, RADIOLIB_PIN_TYPE busy, 
-    SPIClass &spi,
-    PhysicalLayer *iface);
+    RadioLibInterface(RADIOLIB_PIN_TYPE cs, RADIOLIB_PIN_TYPE irq, RADIOLIB_PIN_TYPE rst, RADIOLIB_PIN_TYPE busy, SPIClass &spi,
+                      PhysicalLayer *iface);
 
     virtual ErrorCode send(MeshPacket *p);
 
@@ -48,51 +51,9 @@ class RadioLibInterface : public RadioInterface
     /// \return true if initialisation succeeded.
     virtual bool init() { return true; }
 
-    /// Sets the transmitter and receiver
-    /// centre frequency.
-    /// \param[in] centre Frequency in MHz. 137.0 to 1020.0. Caution: RFM95/96/97/98 comes in several
-    /// different frequency ranges, and setting a frequency outside that range of your radio will probably not work
-    /// \return true if the selected frquency centre is within range
-    bool setFrequency(float centre) { return true; }
-
-    /// Select one of the predefined modem configurations. If you need a modem configuration not provided
-    /// here, use setModemRegisters() with your own ModemConfig.
-    /// Caution: the slowest protocols may require a radio module with TCXO temperature controlled oscillator
-    /// for reliable operation.
-    /// \param[in] index The configuration choice.
-    /// \return true if index is a valid choice.
-    bool setModemConfig(RH_RF95::ModemConfigChoice index) { return true; }
-
-    /// If current mode is Rx or Tx changes it to Idle. If the transmitter or receiver is running,
-    /// disables them.
-    void setModeIdle() {}
-
-    /// If current mode is Tx or Idle, changes it to Rx.
-    /// Starts the receiver in the RF95/96/97/98.
-    void setModeRx() {}
-
-    /// Returns the operating mode of the library.
-    /// \return the current mode, one of RF69_MODE_*
-    virtual RHGenericDriver::RHMode mode() { return RHGenericDriver::RHModeIdle; }
-
-    /// Sets the transmitter power output level, and configures the transmitter pin.
-    /// Be a good neighbour and set the lowest power level you need.
-    /// Some SX1276/77/78/79 and compatible modules (such as RFM95/96/97/98)
-    /// use the PA_BOOST transmitter pin for high power output (and optionally the PA_DAC)
-    /// while some (such as the Modtronix inAir4 and inAir9)
-    /// use the RFO transmitter pin for lower power but higher efficiency.
-    /// You must set the appropriate power level and useRFO argument for your module.
-    /// Check with your module manufacturer which transmtter pin is used on your module
-    /// to ensure you are setting useRFO correctly.
-    /// Failure to do so will result in very low
-    /// transmitter power output.
-    /// Caution: legal power limits may apply in certain countries.
-    /// After init(), the power will be set to 13dBm, with useRFO false (ie PA_BOOST enabled).
-    /// \param[in] power Transmitter power level in dBm. For RFM95/96/97/98 LORA with useRFO false,
-    /// valid values are from +5 to +23.
-    /// For Modtronix inAir4 and inAir9 with useRFO true (ie RFO pins in use),
-    /// valid values are from -1 to 14.
-    /// \param[in] useRFO If true, enables the use of the RFO transmitter pins instead of
-    /// the PA_BOOST pin (false). Choose the correct setting for your module.
-    void setTxPower(int8_t power, bool useRFO = false) {}
+  protected:
+    /**
+     * Convert our modemConfig enum into wf, sf, etc...
+     */
+    void applyModemConfig();
 };