add support for seeed wio tracker L1 (#6907)

* add support for seeed  wio tracker l1

* add support in nrf52 arch

* fix ADC problem and comments incorrect

* fix gps wakeup pin

* fix gps pin

variants/seeed_wio_tracker_L1/variant.h

@@ -0,0 +1,185 @@
+#ifndef _SEEED_TRACKER_L1_H_
+#define _SEEED_TRACKER_L1_H_
+#include "WVariant.h"
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+//  Clock Configuration
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+#define VARIANT_MCK (64000000ul) // Master clock frequency
+#define USE_LFXO                 // 32.768kHz crystal for LFCLK
+
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+//  Pin Capacity Definitions
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+#define PINS_COUNT (33u)       // Total GPIO pins
+#define NUM_DIGITAL_PINS (33u) // Digital I/O pins
+#define NUM_ANALOG_INPUTS (8u) // Analog inputs (A0-A5 + VBAT + AREF)
+#define NUM_ANALOG_OUTPUTS (0u)
+
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+//  LED Configuration
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+//  LEDs
+//  LEDs
+#define PIN_LED1 (11) // LED        P1.15
+#define PIN_LED2 (12) //
+
+#define LED_BUILTIN PIN_LED1
+#define LED_CONN PIN_LED2
+
+#define LED_GREEN PIN_LED1
+#define LED_BLUE PIN_LED2
+// #define LED_PIN PIN_LED2
+#define LED_STATE_ON 1 // State when LED is litted
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+//  Button Configuration
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+#define BUTTON_PIN D13 // This is the Program Button
+// #define BUTTON_NEED_PULLUP   1
+#define BUTTON_ACTIVE_LOW true
+#define BUTTON_ACTIVE_PULLUP false
+
+#define BUTTON_PIN_TOUCH 13 // Touch button
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+//  Digital Pin Mapping (D0-D10)
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+#define D0 0   // P1.06 GNSS_WAKEUP/IO0
+#define D1 1   // P0.07 LORA_DIO1
+#define D2 2   // P1.07 LORA_RESET
+#define D3 3   // P1.10 LORA_BUSY
+#define D4 4   // P1.14 LORA_CS
+#define D5 5   // P1.08 LORA_SW
+#define D6 6   // P0.27 GNSS_TX
+#define D7 7   // P0.26 GNSS_RX
+#define D8 8   // P0.30 SPI_SCK
+#define D9 9   // P0.03 SPI_MISO
+#define D10 10 // P0.28 SPI_MOSI
+#define D12 12 // P1.00 Buzzer
+#define D13 13 // P0.08 User Button
+#define D14 14 // P0.05 OLED SCL
+#define D15 15 // P0.06 OLED SDA
+#define D16 16 // P0.31 VBAT_ADC
+#define D17 17 // P0.00 GROVE SDA
+#define D18 18 // P0.01 GROVE_SCL
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+//  Analog Pin Definitions
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+#define PIN_A0 0     // P0.02 Analog Input 0
+#define PIN_A1 1     // P0.03 Analog Input 1
+#define PIN_A2 2     // P0.28 Analog Input 2
+#define PIN_A3 3     // P0.29 Analog Input 3
+#define PIN_A4 4     // P0.04 Analog Input 4
+#define PIN_A5 5     // P0.05 Analog Input 5
+#define PIN_VBAT D16 // P0.31 Battery voltage sense
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+//  Communication Interfaces
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+//  I2C Configuration
+#define HAS_WIRE 1
+#define PIN_WIRE_SDA D14 // P0.09
+#define PIN_WIRE_SCL D15 // P0.10
+#define WIRE_INTERFACES_COUNT 1
+#define I2C_NO_RESCAN
+
+static const uint8_t SDA = PIN_WIRE_SDA;
+static const uint8_t SCL = PIN_WIRE_SCL;
+
+#define HAS_SCREEN 1
+#define USE_SSD1306 1
+
+// SPI Configuration (SX1262)
+
+#define SPI_INTERFACES_COUNT 1
+#define PIN_SPI_MISO 9  // P0.03 (D9)
+#define PIN_SPI_MOSI 10 // P0.28 (D10)
+#define PIN_SPI_SCK 8   // P0.30 (D8)
+
+// SX1262 LoRa Module Pins
+#define USE_SX1262
+#define SX126X_CS D4                 // Chip select
+#define SX126X_DIO1 D1               // Digital IO 1 (Interrupt)
+#define SX126X_BUSY D3               // Busy status
+#define SX126X_RESET D2              // Reset control
+#define SX126X_DIO3_TCXO_VOLTAGE 1.8 // TCXO supply voltage
+#define SX126X_RXEN D5               // RX enable control
+#define SX126X_TXEN RADIOLIB_NC
+#define SX126X_DIO2_AS_RF_SWITCH // This Line is really necessary for SX1262  to work with RF switch or will loss TX power
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+//  Power Management
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+
+#define BAT_READ                                                                                                                 \
+    30 // D30 = P0.04  Reads battery voltage from divider on signal board. 
+#define BATTERY_SENSE_RESOLUTION_BITS 12
+#define ADC_MULTIPLIER 2.0 
+#define BATTERY_PIN PIN_VBAT // PIN_A7
+#define AREF_VOLTAGE 3.6
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+//  GPS L76KB
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+#define GPS_L76K
+#ifdef GPS_L76K
+#define PIN_GPS_RX D6 // P0.26
+#define PIN_GPS_TX D7
+#define HAS_GPS 1
+#define GPS_BAUDRATE 9600
+#define GPS_THREAD_INTERVAL 50
+#define PIN_SERIAL1_RX PIN_GPS_TX
+#define PIN_SERIAL1_TX PIN_GPS_RX
+
+#define GPS_RX_PIN PIN_GPS_TX
+#define GPS_TX_PIN PIN_GPS_RX
+#define PIN_GPS_STANDBY D0
+
+// #define GPS_DEBUG
+//  #define GPS_EN D18 // P1.05
+#endif
+
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+//  On-board QSPI Flash
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+// On-board QSPI Flash
+#define PIN_QSPI_SCK (21)
+#define PIN_QSPI_CS (22)
+#define PIN_QSPI_IO0 (23)
+#define PIN_QSPI_IO1 (24)
+#define PIN_QSPI_IO2 (25)
+#define PIN_QSPI_IO3 (26)
+
+#define EXTERNAL_FLASH_DEVICES P25Q16H
+#define EXTERNAL_FLASH_USE_QSPI
+
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+//  Buzzer
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+// Buzzer
+
+#define PIN_BUZZER D12 // P1.00, pwm output
+
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+//  joystick
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+
+#define CANNED_MESSAGE_MODULE_ENABLE 1
+
+// trackball
+#define HAS_TRACKBALL 1
+#define TB_UP 25
+#define TB_DOWN 26
+#define TB_LEFT 27
+#define TB_RIGHT 28
+#define TB_PRESS 29
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+//  Compatibility Definitions
+// ━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━
+#ifdef __cplusplus
+extern "C" {
+#endif
+// Serial port placeholders
+
+#define PIN_SERIAL2_RX (-1)
+#define PIN_SERIAL2_TX (-1)
+#ifdef __cplusplus
+}
+#endif
+
+#endif //  _SEEED_SOLAR_NODE_H_