Merge branch 'master' into raspi-portduino

variants/diy/dr-dev/variant.h

@@ -2,6 +2,8 @@
 #define HAS_SCREEN 0
 #define I2C_SDA 4
 #define I2C_SCL 5
+#define BATTERY_PIN 34
+#define ADC_CHANNEL ADC1_GPIO34_CHANNEL
 
 // GPS
 #undef GPS_RX_PIN
@@ -67,4 +69,4 @@
 #define USE_SX1262
 //#define USE_SX1268
 //#define USE_LLCC68
-#define SX126X_E22
+#define SX126X_E22

variants/diy/v1/variant.h

@@ -9,8 +9,9 @@
 #define GPS_TX_PIN 15
 #define GPS_UBLOX
 
-#define BUTTON_PIN 39       // The middle button GPIO on the T-Beam
-#define BATTERY_PIN 35      // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
+#define BUTTON_PIN 39  // The middle button GPIO on the T-Beam
+#define BATTERY_PIN 35 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
+#define ADC_CHANNEL ADC1_GPIO35_CHANNEL
 #define ADC_MULTIPLIER 1.85 // (R1 = 470k, R2 = 680k)
 #define EXT_PWR_DETECT 4    // Pin to detect connected external power source for LILYGO® TTGO T-Energy T18 and other DIY boards
 #define EXT_NOTIFY_OUT 12   // Overridden default pin to use for Ext Notify Module (#975).
@@ -38,9 +39,8 @@
 #define SX126X_DIO1 LORA_DIO1
 #define SX126X_BUSY LORA_DIO2
 #define SX126X_RESET LORA_RESET
-//#define SX126X_RXEN 14
-//#define SX126X_TXEN 13
-#define SX126X_POWER_EN (13)
+#define SX126X_RXEN RADIOLIB_NC // Defining the RXEN ruins RFSwitching for the E22 900M30S in RadioLib
+#define SX126X_TXEN 13
 
 // RX/TX for RFM95/SX127x
 #define RF95_RXEN 14
@@ -53,4 +53,4 @@
 // Internally the TTGO module hooks the SX126x-DIO2 in to control the TX/RX switch
 // (which is the default for the sx1262interface code)
 #define SX126X_E22
-#endif
+#endif

variants/heltec_v1/variant.h

@@ -27,3 +27,5 @@
 #define ADC_MULTIPLIER 3.2
 
 #define BATTERY_PIN 13 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
+#define ADC_CHANNEL ADC2_GPIO13_CHANNEL
+#define BAT_MEASURE_ADC_UNIT 2

variants/heltec_v2.1/variant.h

@@ -29,5 +29,6 @@
 
 #define ADC_MULTIPLIER 3.8
 
-#define BATTERY_PIN 37    // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
-#define EXT_NOTIFY_OUT 13 // Default pin to use for Ext Notify Module.
+#define BATTERY_PIN 37 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
+#define ADC_CHANNEL ADC1_GPIO37_CHANNEL
+#define EXT_NOTIFY_OUT 13 // Default pin to use for Ext Notify Module.

variants/heltec_v2/variant.h

@@ -27,3 +27,5 @@
 // ratio of voltage divider = 3.20 (R12=100k, R10=220k)
 #define ADC_MULTIPLIER 3.2
 #define BATTERY_PIN 13 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
+#define ADC_CHANNEL ADC2_GPIO13_CHANNEL
+#define BAT_MEASURE_ADC_UNIT 2

variants/heltec_v3/variant.h

@@ -8,7 +8,8 @@
 #define BUTTON_PIN 0
 
 #define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
-#define ADC_MULTIPLIER 5.22
+#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
+#define ADC_MULTIPLIER 4.9
 
 #define USE_SX1262
 
@@ -27,4 +28,4 @@
 #define SX126X_DIO1 LORA_DIO1
 #define SX126X_BUSY LORA_DIO2
 #define SX126X_RESET LORA_RESET
-#define SX126X_E22
+#define SX126X_E22

variants/heltec_wsl_v3/variant.h

@@ -9,7 +9,8 @@
 #define BUTTON_PIN 0
 
 #define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
-#define ADC_MULTIPLIER 5.22
+#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
+#define ADC_MULTIPLIER 4.9
 
 #define USE_SX1262
 

variants/nano-g1-explorer/variant.h

@@ -29,8 +29,9 @@
 // code)
 #endif
 
-#define BATTERY_PIN 35           // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
+#define BATTERY_PIN 35 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
+#define ADC_CHANNEL ADC1_GPIO35_CHANNEL
 #define BATTERY_SENSE_SAMPLES 15 // Set the number of samples, It has an effect of increasing sensitivity.
 #define ADC_MULTIPLIER 2
 
-#define USE_SH1107_128_64
+#define USE_SH1107_128_64

variants/station-g1/variant.h

@@ -32,7 +32,8 @@
        // Info:https://uniteng.com/wiki/doku.php?id=meshtastic:station#rf_design_-_lora_station_edition_g1
 #endif
 
-#define BATTERY_PIN 35           // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
+#define BATTERY_PIN 35 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
+#define ADC_CHANNEL ADC1_GPIO35_CHANNEL
 #define BATTERY_SENSE_SAMPLES 30 // Set the number of samples, It has an effect of increasing sensitivity.
 #define ADC_MULTIPLIER 6.45
 #define BAT_FULLVOLT 12600
@@ -41,4 +42,4 @@
 #define BAT_NOBATVOLT 6690
 
 // different screen
-#define USE_SH1106
+#define USE_SH1106

variants/tbeam_v07/variant.h

@@ -6,6 +6,7 @@
 #define BUTTON_PIN 39
 #define BATTERY_PIN 35    // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
 #define EXT_NOTIFY_OUT 13 // Default pin to use for Ext Notify Module.
+#define ADC_CHANNEL ADC1_GPIO35_CHANNEL
 
 #define USE_RF95
 #define LORA_DIO0 26 // a No connect on the SX1262 module

variants/tlora_t3s3_v1/variant.h

@@ -9,6 +9,7 @@
 #define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
 // ratio of voltage divider = 2.0 (R42=100k, R43=100k)
 #define ADC_MULTIPLIER 2.11 // 2.0 + 10% for correction of display undervoltage.
+#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
 
 #define I2C_SDA 18 // I2C pins for this board
 #define I2C_SCL 17

variants/tlora_v1_3/variant.h

@@ -4,6 +4,7 @@
 #define GPS_TX_PIN 13 // per @eugene
 
 #define BATTERY_PIN 35 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
+#define ADC_CHANNEL ADC1_GPIO35_CHANNEL
 
 #define I2C_SDA 21 // I2C pins for this board
 #define I2C_SCL 22

variants/tlora_v2/variant.h

@@ -4,6 +4,7 @@
 #define GPS_TX_PIN 13 // per @eugene
 
 #define BATTERY_PIN 35 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
+#define ADC_CHANNEL ADC1_GPIO35_CHANNEL
 
 #define I2C_SDA 21 // I2C pins for this board
 #define I2C_SCL 22
@@ -19,4 +20,4 @@
 #define LORA_DIO0 26 // a No connect on the SX1262 module
 #define LORA_RESET 14
 #define LORA_DIO1 33 // Must be manually wired: https://www.thethingsnetwork.org/forum/t/big-esp32-sx127x-topic-part-3/18436
-#define LORA_DIO2 32 // Not really used
+#define LORA_DIO2 32 // Not really used

variants/tlora_v2_1_16/variant.h

@@ -3,9 +3,12 @@
 #define GPS_RX_PIN 15 // per @der_bear on the forum, 36 is incorrect for this board type and 15 is a better pick
 #define GPS_TX_PIN 13
 
-#define BATTERY_PIN 35 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
+#define BATTERY_PIN 35
+#define ADC_CHANNEL ADC1_GPIO35_CHANNEL
+#define BATTERY_SENSE_SAMPLES 30
+
 // ratio of voltage divider = 2.0 (R42=100k, R43=100k)
-#define ADC_MULTIPLIER 2.11 // 2.0 + 10% for correction of display undervoltage.
+#define ADC_MULTIPLIER 2
 
 #define I2C_SDA 21 // I2C pins for this board
 #define I2C_SCL 22
@@ -19,4 +22,4 @@
 #define LORA_DIO0 26 // a No connect on the SX1262 module
 #define LORA_RESET 23
 #define LORA_DIO1 33 // https://www.thethingsnetwork.org/forum/t/big-esp32-sx127x-topic-part-3/18436
-#define LORA_DIO2 32 // Not really used
+#define LORA_DIO2 32 // Not really used

variants/tlora_v2_1_18/variant.h

@@ -4,6 +4,7 @@
 #define BATTERY_PIN 35 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
 // ratio of voltage divider = 2.0 (R42=100k, R43=100k)
 #define ADC_MULTIPLIER 2.11 // 2.0 + 10% for correction of display undervoltage.
+#define ADC_CHANNEL ADC1_GPIO35_CHANNEL
 
 #define I2C_SDA 21 // I2C pins for this board
 #define I2C_SCL 22