ESP32s3: Migrate variants to new structure (#7343)

variants/esp32s3/seeed-sensecap-indicator/variant.h

@@ -0,0 +1,80 @@
+#define I2C_SDA 39
+#define I2C_SCL 40
+
+// This board has a serial coprocessor for sensor readings
+#define SENSOR_RP2040_TXD 19
+#define SENSOR_RP2040_RXD 20
+#define SENSOR_PORT_NUM 2
+#define SENSOR_BAUD_RATE 115200
+
+#define BUTTON_PIN 38
+#define BUTTON_ACTIVE_LOW true
+#define BUTTON_ACTIVE_PULLUP true
+
+// #define BUTTON_NEED_PULLUP
+
+// #define BATTERY_PIN 27 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
+// #define ADC_CHANNEL ADC1_GPIO27_CHANNEL
+// #define ADC_MULTIPLIER 2
+
+// ST7701 TFT LCD
+#define ST7701_CS (4 | IO_EXPANDER)
+#define ST7701_RS -1  // DC
+#define ST7701_SDA 48 // MOSI
+#define ST7701_SCK 41
+#define ST7701_RESET (5 | IO_EXPANDER)
+#define ST7701_MISO 47
+#define ST7701_BUSY -1
+#define ST7701_BL 45
+#define ST7701_SPI_HOST SPI2_HOST
+#define ST7701_BACKLIGHT_EN 45
+#define SPI_FREQUENCY 12000000
+#define TFT_HEIGHT 480
+#define TFT_WIDTH 480
+#define TFT_OFFSET_X 0
+#define TFT_OFFSET_Y 0
+#define TFT_OFFSET_ROTATION 0
+#define TFT_BL 45
+#define SCREEN_ROTATE
+#define SCREEN_TRANSITION_FRAMERATE 5 // fps
+
+#define HAS_TOUCHSCREEN 1
+#define SCREEN_TOUCH_INT (6 | IO_EXPANDER)
+#define SCREEN_TOUCH_RST (7 | IO_EXPANDER)
+#define TOUCH_I2C_PORT 0
+#define TOUCH_SLAVE_ADDRESS 0x48
+
+// in future, we may want to add a buzzer and add all sensors to the indicator via a data protocol for now only GPS is supported
+// // Buzzer
+// #define PIN_BUZZER 19
+
+#define GPS_DEFAULT_NOT_PRESENT 1
+#define GPS_RX_PIN 20
+#define GPS_TX_PIN 19
+#define HAS_GPS 1
+
+#define USE_SX1262
+#define USE_SX1268
+
+#define LORA_SCK 41
+#define LORA_MISO 47
+#define LORA_MOSI 48
+#define LORA_CS (0 | IO_EXPANDER)
+
+#define LORA_DIO0 -1 // a no connect on the SX1262 module
+#define LORA_RESET (1 | IO_EXPANDER)
+#define LORA_DIO1 (3 | IO_EXPANDER) // SX1262 IRQ
+#define LORA_DIO2 (2 | IO_EXPANDER) // SX1262 BUSY
+#define LORA_DIO3
+
+#define SX126X_CS LORA_CS
+#define SX126X_DIO1 LORA_DIO1
+#define SX126X_BUSY LORA_DIO2
+#define SX126X_RESET LORA_RESET
+#define SX126X_DIO2_AS_RF_SWITCH
+
+#define TCXO_OPTIONAL // handle Indicator V1 and V2
+#define SX126X_DIO3_TCXO_VOLTAGE 2.4
+
+#define USE_VIRTUAL_KEYBOARD 1
+#define DISPLAY_CLOCK_FRAME 1