Release Develop to Master

variants/tlora_t3s3_v1/pins_arduino.h

@@ -0,0 +1,34 @@
+#ifndef Pins_Arduino_h
+#define Pins_Arduino_h
+
+#include <stdint.h>
+
+#define USB_VID 0x303a
+#define USB_PID 0x1001
+
+#define EXTERNAL_NUM_INTERRUPTS 46
+#define NUM_DIGITAL_PINS        48
+#define NUM_ANALOG_INPUTS       20
+
+#define analogInputToDigitalPin(p)  (((p)<20)?(analogChannelToDigitalPin(p)):-1)
+#define digitalPinToInterrupt(p)    (((p)<48)?(p):-1)
+#define digitalPinHasPWM(p)         (p < 46)
+
+// The default Wire will be mapped to PMU and RTC
+static const uint8_t SDA = 18;
+static const uint8_t SCL = 17;
+
+// Default SPI will be mapped to Radio
+static const uint8_t SS    = 7;
+static const uint8_t MOSI  = 6;
+static const uint8_t MISO  = 3;
+static const uint8_t SCK   = 5;
+
+#define SPI_MOSI                    (11)
+#define SPI_SCK                     (14)
+#define SPI_MISO                    (2)
+#define SPI_CS                      (13)
+
+#define SDCARD_CS                   SPI_CS
+
+#endif /* Pins_Arduino_h */

variants/tlora_t3s3_v1/platformio.ini

@@ -0,0 +1,9 @@
+[env:tlora-t3s3-v1]
+extends = esp32s3_base
+board = tlora-t3s3-v1
+lib_deps =
+  ${esp32_base.lib_deps}
+  caveman99/ESP32 Codec2@^1.0.1
+
+build_flags = 
+  ${esp32_base.build_flags} -D TLORA_T3S3_V1 -I variants/tlora_t3s3_v1

variants/tlora_t3s3_v1/variant.h

@@ -0,0 +1,54 @@
+#undef GPS_RX_PIN
+#undef GPS_TX_PIN
+
+#define HAS_SDCARD
+#define SDCARD_USE_SPI1
+
+#define USE_SSD1306
+
+#define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
+// ratio of voltage divider = 2.0 (R42=100k, R43=100k)
+#define ADC_MULTIPLIER 2.11 // 2.0 + 10% for correction of display undervoltage.
+
+#define I2C_SDA 18 // I2C pins for this board
+#define I2C_SCL 17
+
+#define LED_PIN 37     // If defined we will blink this LED
+#define BUTTON_PIN 0  // If defined, this will be used for user button presses,
+
+#define BUTTON_NEED_PULLUP
+
+// TTGO uses a common pinout for their SX1262 vs RF95 modules - both can be enabled and we will probe at runtime for RF95 and if
+// not found then probe for SX1262
+#define USE_RF95 // RFM95/SX127x
+#define USE_SX1262
+#define USE_SX1280
+
+#define RF95_SCK 5
+#define RF95_MISO 3
+#define RF95_MOSI 6
+#define RF95_NSS 7
+
+#define LORA_RESET 8
+#define LORA_DIO0 9
+#define LORA_DIO1 9
+#define LORA_DIO2 33 // SX1262 BUSY
+#define LORA_DIO3 34 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled
+
+#ifdef USE_SX1262
+#define SX126X_CS RF95_NSS // FIXME - we really should define LORA_CS instead
+#define SX126X_DIO1 LORA_DIO1
+#define SX126X_BUSY 36
+#define SX126X_RESET LORA_RESET
+#define SX126X_RXEN 21
+#define SX126X_TXEN 10
+#endif
+
+#ifdef USE_SX1280
+#define SX128X_CS RF95_NSS
+#define SX128X_DIO1 LORA_DIO1
+#define SX128X_BUSY 36
+#define SX128X_RESET LORA_RESET
+#define SX128X_RXEN 21
+#define SX128X_TXEN 10
+#endif

variants/tlora_v2_1_18/platformio.ini

@@ -5,7 +5,5 @@ lib_deps =
   ${esp32_base.lib_deps}
   caveman99/ESP32 Codec2@^1.0.1
 
-; the RADIOLIB_GODMODE flag can be removed once the next version of RadioLib is released. (>5.5.0)
-
 build_flags = 
-  ${esp32_base.build_flags} -D TLORA_V2_1_18 -I variants/tlora_v2_1_18 -D RADIOLIB_GODMODE
+  ${esp32_base.build_flags} -D TLORA_V2_1_18 -I variants/tlora_v2_1_18