mirror of
https://github.com/meshtastic/firmware.git
synced 2025-12-14 06:42:34 +00:00
60 lines
1.7 KiB
C
60 lines
1.7 KiB
C
|
#define TFT_BL 2
|
||
|
|
#define SPI_FREQUENCY 2000000
|
||
|
|
#define SPI_READ_FREQUENCY 16000000
|
||
|
|
#define TFT_HEIGHT 142
|
||
|
|
#define TFT_WIDTH 428
|
||
|
|
#define TFT_OFFSET_X 0
|
||
|
|
#define TFT_OFFSET_Y 0
|
||
|
|
#define TFT_OFFSET_ROTATION 0
|
||
|
|
#define SCREEN_TRANSITION_FRAMERATE 5
|
||
|
|
#define HAS_SCREEN 1
|
||
|
|
#define TFT_BLACK 0
|
||
|
|
#define BRIGHTNESS_DEFAULT 130 // Medium Low Brightness
|
||
|
|
|
||
|
|
#define USE_POWERSAVE
|
||
|
|
#define SLEEP_TIME 120
|
||
|
|
|
||
|
|
#define GPS_DEFAULT_NOT_PRESENT 1
|
||
|
|
// #define GPS_RX_PIN 44
|
||
|
|
// #define GPS_TX_PIN 43
|
||
|
|
|
||
|
|
// #define BATTERY_PIN 4 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
|
||
|
|
// ratio of voltage divider = 2.0 (RD2=100k, RD3=100k)
|
||
|
|
// #define ADC_MULTIPLIER 2.11 // 2.0 + 10% for correction of display undervoltage.
|
||
|
|
// #define ADC_CHANNEL ADC1_GPIO4_CHANNEL
|
||
|
|
|
||
|
|
// keyboard
|
||
|
|
#define I2C_SDA 47 // I2C pins for this board
|
||
|
|
#define I2C_SCL 14
|
||
|
|
// #define KB_POWERON -1 // must be set to HIGH
|
||
|
|
// #define KB_SLAVE_ADDRESS TDECK_KB_ADDR // 0x55
|
||
|
|
// #define KB_BL_PIN 46 // not used for now
|
||
|
|
#define KB_INT 13
|
||
|
|
#define CANNED_MESSAGE_MODULE_ENABLE 1
|
||
|
|
|
||
|
|
#define TFT_DC 39
|
||
|
|
#define TFT_CS 41
|
||
|
|
|
||
|
|
// LoRa
|
||
|
|
#define USE_SX1262
|
||
|
|
|
||
|
|
#define LORA_SCK 8
|
||
|
|
#define LORA_MISO 9
|
||
|
|
#define LORA_MOSI 3
|
||
|
|
#define LORA_CS 17
|
||
|
|
|
||
|
|
// #define LORA_DIO0 -1 // a No connect on the SX1262 module
|
||
|
|
#define LORA_RESET 18
|
||
|
|
#define LORA_DIO1 16 // SX1262 IRQ
|
||
|
|
#define LORA_DIO2 15 // SX1262 BUSY
|
||
|
|
// #define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled
|
||
|
|
|
||
|
|
#define SX126X_CS LORA_CS
|
||
|
|
#define SX126X_DIO1 LORA_DIO1
|
||
|
|
#define SX126X_BUSY LORA_DIO2
|
||
|
|
#define SX126X_RESET LORA_RESET
|
||
|
|
|
||
|
|
#define SX126X_DIO2_AS_RF_SWITCH
|
||
|
|
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
|
||
|
|
|
||
|
|
// #define LED_PIN 1
|